1. Manuals
  2. Brands
  3. Seneca Manuals
  4. Conference System
  5. Z-LINK1
  6. Installation manual

Seneca Z-LINK1 Installation Manual

Radio communication device
Hide thumbs
1
2
3
4
5
6
7
8

Advertisement

Table of Contents

SENECA
S
EN
EN
EN
EN
Installation
Installation
Installation
Installation
Manual
Manual
Manual
Manual
Contents:
- General features
- Technical specifications
- Installation and connections
- Functioning
- Programming
- LEDs signallings
- Countries in which the Z-LINK1 can be
used
SENECA s.r.l.
Via Austria, 26 - 35127 - PADOVA - ITALY
Tel. +39.049.8705355 - 8705359 - Fax +39.049.8706287
For manual and configuration softwares, see www.seneca.it
This document is property of SENECA srl. Duplication and reprodution are forbidden, if not
Contents of the present documentation refers to products and technologies described in it. All technical data
contained in the document may be modified without prior notice Content of this documentation is subject to
periodical revision.
Z-LINK1
Z-LINK1
Radio communication device
MI002875-E
authorized.
ENGLISH 1/8

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Z-LINK1 and is the answer not in the manual?

Questions and answers

Related Manuals for Seneca Z-LINK1

Summary of Contents for Seneca Z-LINK1

  • Page 1 Tel. +39.049.8705355 - 8705359 - Fax +39.049.8706287 For manual and configuration softwares, see www.seneca.it This document is property of SENECA srl. Duplication and reprodution are forbidden, if not authorized. Contents of the present documentation refers to products and technologies described in it. All technical data contained in the document may be modified without prior notice Content of this documentation is subject to periodical revision.
  • Page 2 The Z-LINK1 modules represent a communication systems for data acquisition and transmission in the process control and industrial / civil automation. Based on an UHF modem radio, Z-LINK1 is able to comunicate with Z-PC line modules through ModBUS protocol. Z-LINK1 represents a new platform communication in radio frequency.
  • Page 3 Accessories : Cable: RJ10/DB9F (PM001420) Directional antenna - 2.5 m - SMA (ANT-MAG) Seneca bus accessories: Z-PC-DIN The Z-LINK1 complies with the following standards: Standards: ETSI EN 300 220-2 V2.1.2 (2007-06) ETSI EN 301 489-3 V1.4.1 (2002-08) CEI EN 61010...
  • Page 4 As it is illustrated in the next figure: 1) Insert the rear IDC10 connector on a DIN rail free slot (the inserting is univocal since the connectors are polarized). 2) Tighten the locks placed at the sides of the rear IDC10 connector to fix the module.
  • Page 5 RS232 serial port from RJ10 or terminals The module Z-LINK1 has the RS232 communication port by RJ10 or screw terminals 4, 5, 6, 1 as shown in the following figure. The RJ10 port is the RS232 physical replica of the RS485 signal via radio.
  • Page 6 Each Z-LINK1 can be configured as: - BRIDGE: the Z-LINK1 has not the CPU enabled. To complete the configuration, set if the Z- LINK1 is connected to the Modbus master (PLC, PC, etc...) and Modbus slaves (local bus), or if the Z-LINK1 is only connected to Modbus slaves (local bus).
  • Page 7 Z-LINK1 device connected to the interested Modbus slave device, too (for example, the previous Z-LINK1 connected to the Z- 4AI via local bus).
  • Page 8 NOTE: the Z-LINK1 devices are not suitable for safety applications. COUNTRIES IN WHICH THE Z-LINK1 CAN BE USED The countries in which the devices can be used Z-LINK1 are compatible ERC REC 70-03 (Annex 1, G3): Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark, Estonia,...

This manual is also suitable for:

Z-link1-nm

Table of Contents