Table of Contents
Advertisement
Quick Links
Wireless DMX Transmitter
Receiver and Splitter
Instruction Manual
Models:
DST4W-PRO-3, DST4W-PRO-5
DST4W-PRO-C
version 1.0 since 7 June 2017
ATTENTION!
This instruction manual contains important information about the installation and the use of
the equipment. Please read and follow these instructions carefully.
Always ensure that the power to the equipment is disconnected before opening the
equipment or commencing any maintenance work.
DST4W-PRO_en_manual_M085
( 1 / 8)
Advertisement
Table of Contents
Summary of Contents for SRS Lighting DST4W-PRO-3
- Page 1 Wireless DMX Transmitter Receiver and Splitter Instruction Manual Models: DST4W-PRO-3, DST4W-PRO-5 DST4W-PRO-C version 1.0 since 7 June 2017 ATTENTION! This instruction manual contains important information about the installation and the use of the equipment. Please read and follow these instructions carefully.
- Page 2 IMPORTANT SAFETY INFORMATION The following general safety precautions have to be observed during all phases of operation, service, and the repair of this equipment. Failure to comply with these precautions or with specific warnings in this manual violates safety standards of design, manufacture, and the intended use of this equipment. Do not operate in an explosive atmosphere! Do not operate this equipment in the presence of flammable gases or fumes.
- Page 3 Front panel: Rear panel: Device in use / service: By default, Power LED indicates the device is on main power. When the Power LED is off, check the main power input. The unit can be supplied with AC85-264V or AC/DC battery power. There is no polarity restriction for this port.
- Page 4 DMX-only operation For the DMX operation, turn off the W- DMX module by holding the MODE button. Both W-DMX and MODE buttons light in red color. Connect the DMX cable to the DMX-IN connector and use the DST4W-PRO as a standard one-to-four isolated...
- Page 5 W-DMX Receiver / Splitter You can use the DST4W-PRO as a Receiver with the Splitter output. There is an automatic back-up of the W-DMX line using the cable connection. If the W-DMX is linked to the transmitter and the signal quality is poor, the W-DMX active LED goes off and the splitter will retransmit signal from cable in/thru port.
- Page 6 W-DMX Transmitter / Splitter The DST4W-PRO can be used in the Transmitter and DMX splitter mode at the same time. The DMX signal from input/thru is sent out via Wireless DMX to all other linked W-DMX devices. Signal bargraph LEDs are blinking in a row to indicate that the module is in the Transmitter mode.
- Page 7 Technical data Mains input: AC 100-255V / 50-60Hz / 5W Battery input: AC12-24V / 5W or DC12-24V /5W Input / Output: 4x USITT DMX512 /RS485/ isolated up to 1000V Housing & Dimensions: Lightweight Aluminum box with powder coating: 234x154x62mm Mounting points: Located symmetrically on the base plate, 8mm-wide hole for securing line Grid of mounting points: 222x78mm, 4x rubber foot on the bottom Operating temperature:...
- Page 8 Copyright 2017 SRS Group, s.r.o. | Specifications subject to change without notice. Document: DST4W-PRO_en_manual_M085 | Version 1.0 | Actual as of: 7 June 2017 SRS Group s.r.o. Rybnicna 36/D | 831 07 Bratislava | Slovakia Phone: +421 2 44 681 417 | Fax: +421 2 4468 1419 Email: sales@srs-group.com | www.srs-group.com ( 8 / 8)
Need help?
Do you have a question about the DST4W-PRO-3 and is the answer not in the manual?
Questions and answers