1. Manuals
  2. Brands
  3. Apevia Manuals
  4. Enclosure
  5. X-Jupiter Jr
  6. Install manual

Apevia X-Jupiter Jr Install Manual

Apevia x-jupiter jr chassis: install guide
Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the X-Jupiter Jr and is the answer not in the manual?

Questions and answers

Related Manuals for Apevia X-Jupiter Jr

Summary of Contents for Apevia X-Jupiter Jr

  • Page 2: Table Of Contents

    1. Motherboard installation...1 2. Install 3½” and 5¼” 3. Install PCI components...4 4. Case fan setup...5 5. Temperature probe setup...6 Connect case leads to motherboard Identify the power supply connectors 8. Complete the installation...9 9. USB/1394/Audio cable pin assignments...9 drives...3 ...7 ...8...

  • Page 3: Motherboard Installation

    Please refer to each components’ documentation for instructions. 1. Motherboard installation: 1.1 Remove thumbscrews from the rear of the X-Jupiter Jr. X-Jupiter Jr. Finished Appearance. 1.2 Grab the notch on the left panel. Pull until the panel is released and remove.
  • Page 4 Remove panel. NOTE: Touch an unpainted metal section of the chassis to discharge static electricity before handling PC components. An anti-static wrist strap should also be worn to further minimize the possibility of damage.

  • Page 5: Install 3½" And 5¼" Drives

    2. Install 3½” and 5¼” 2.1 To install an optical or floppy drive, remove the drive cover by placing an index finger into either inlet and pulling outward. 2.3 Slide the blue drive-rail forward and push the clamp downwards to engage locking mechanism. No screws are necessary, but can be used optionally on opti- cal and floppy drive bays.

  • Page 6: Install Pci Components

    3.1 First, remove the PCI slot covers. Firmly press point A with thumb, while pulling point B with index finger to open the latch. 3.2 From the outside rear of the case, push PCI slot cover(s) toward the inside of the chassis.

  • Page 7: Case Fan Setup

    3.3 1st, read your expansion card’s documentation. Install PCI card into correct slot for your card type (x1, x16, etc.). 4. Case fan setup: 4.1 Daisy chain the fans to be regulated using the fan speed controller. Con- nect male to female ends and plug the last male end into the fan controller connector labeled ‘OUT- PUT’.

  • Page 8: Temperature Probe Setup

    5.1 Locate the device temperature probes. Note: You may also leave a sensor loose in the chassis in order to monitor the ambient system temperature. DO NOT place the sensor directly on the CPU as it will damage the sensor.

  • Page 9: Connect Case Leads To Motherboard

    5.5 Monitor system temperatures from the front panel LCD. 6. Connect case leads to motherboard: 6.1 Locate the top panel leads. Your motherboard documentation will provide schematics. The triang- ular markings indicate positive wires. (Remove right-side panel to better access wiring.) Locate front panel leads.

  • Page 10: Identify The Power Supply Connectors

    7. Identify the power supply connectors: 7.1 20/24 pin ATX connector. 7.3 Serial ATA (SATA) connector. 7.5 6-pin PCI-Express connector. Connect PC components to the required power connector for each device type. 7.2 ATX 12V P4 CPU connector. 7.4 4-pin peripheral connector. 7.6 Floppy drive connector.

  • Page 11: Complete The Installation

    8. Complete the installation: 8.1 With all components properly installed, gently return side panels to their original positions and replace all screws. Congratulations! You have completed assembly of the X-Jupiter Jr. 9. USB/1394/Audio cable pin assignments:...

Table of Contents