1. Manuals
  2. Brands
  3. Okolab Manuals
  4. Climate chamber
  5. H301-NIKON-NZ100/200/500-N
  6. User manual

Okolab H301-NIKON-NZ100/200/500-N User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
H301-NIKON-NZ100/200/500-N
Compatible with the following XY stages
•
Mad City Labs NZ100/200/500-N on Nikon me-
chanical or motorized stages, TI-S-E and TI-S-
ER.
www.oko-lab.com
H301-NIKON-NZ100/200/500-N
User Manual
Compatible with the following Okolab Controllers
•
H301-T-BL-PLUS
•
UNO-T
•
UNO-T-H-PREMIXED
•
UNO-T-H-CO2
Rev 03

Advertisement

Table of Contents
loading

Summary of Contents for Okolab H301-NIKON-NZ100/200/500-N

  • Page 1 User Manual H301-NIKON-NZ100/200/500-N Rev 03 H301-NIKON-NZ100/200/500-N Compatible with the following XY stages Compatible with the following Okolab Controllers • • Mad City Labs NZ100/200/500-N on Nikon me- H301-T-BL-PLUS chanical or motorized stages, TI-S-E and TI-S- • UNO-T • UNO-T-H-PREMIXED •...

  • Page 2: Table Of Contents

    User Manual H301-NIKON-NZ100/200/500-N Rev 03 Index Components and dimensions....................3 Available Sample Holders ....................... 3 Available Lids ........................5 3.1 Sliding lid .......................... 5 3.2 Koehler Lid ........................6 3.3 Injection Lid ........................6 3.4 Laser Interlock Lid ....................... 7 Insertion of the Sample Feedback Temperature Sensor ..............

  • Page 3: Components And Dimensions

    Sample Holder-Order Separately Chamber Riser Chamber top view Chamber Base Figure 1. H301-NIKON-NZ100/200/500-N. Components and Dimensions. 2. Available Sample Holders The following sample holders are available. NOTE: Please contact info@oko-lab.com if you cannot find the sample holder you are looking for. We are constantly adding new inserts to the list.
  • Page 4 User Manual H301-NIKON-NZ100/200/500-N Rev 03 GS35-M #1 1x3in. chamber slide and #2 35mm Petri-dish LABTEK-35-M #1 Lab-Tek 1in.x2in. chambered cover glass and #2 35mm Petri-dish LABTEK-II-35-M #1 Lab-Tek II 1in.x2in. chambered cover glass and #2 35mm Petri-dish LABTEK-60-M #1 Lab-Tek 1in.x2in. chambered cover glass and #1 60mm Petri-dish LABTEK-II-60-M #1 Lab-Tek II 1in.x2in.

  • Page 5: Available Lids

    3. Available Lids The following heated glass Lids are available for H301-NIKON-NZ100/200/500-N: • H301-SLIDING-LID: For easy sample loading and pipetting – Included in code H301-NIKON-NZ100/200/500-N. Compatible with Mad City Labs NZ100/200 ONLY. • H301-KOEHLER-LID*: Reduces chamber height to 22 mm and allows imaging under Koehler illumination •...

  • Page 6: Koehler Lid

    Chamber top view Figure 5. H301-NIKON-NZ100/200/500-N + H301-KOEHLER-LID Injection Lid The Injection Lid is a heated glass lid with two small openings sealed with flexible plastic allowing injection or perma- nent access to the sample.

  • Page 7: Laser Interlock Lid

    Chamber top view Figure 6. H301-NIKON-NZ100/200/500-N + H301-INJECTION-LID Laser Interlock Lid The Laser Interlock Lid is a heated glass lid with a safety switch connecting to the laser controller. It automatically turns the laser off when the lid is lifted.

  • Page 8: Insertion Of Sample Holder Into Chamber

    User Manual H301-NIKON-NZ100/200/500-N Rev 03 Temperature Sensor dedicated opening Temperature Sensor dedicated opening 1.Frontal view 2.3D view Figure 8. Insertion of the temperature sensor inside the chamber. 5. Insertion of Sample Holder into Chamber Sample holders fit into the chamber base and are held in place by magnets embedded within both chamber and hold- er.

  • Page 9: Working With 35 Or 60 Mm Petri Dish - Spacing Rings And Magnetic Locks

    User Manual H301-NIKON-NZ100/200/500-N Rev 03 6. Working with 35 or 60 mm Petri Dish – Spacing Rings and Magnetic Locks Magnetic locks prevent movement of 35 and 60 mm dishes inside the sample holder. Figure 10 illustrates the available magnetic locks for 35 and 60 mm dishes. Threaded magnetic posts allow adjusting holder’s height.
  • Page 10 User Manual H301-NIKON-NZ100/200/500-N Rev 03 Grainer-Petri35x10 Ibidi μ-Dish 35 mm-low BD Falcon-35x10 Willco-35x10 Corning-35x10 mm MatTek-P35G-X14-X Figure 12. Ring selection scheme for 35 mm dish. Ibidi μ-Dish 50 mm-low MatTek-P50G-X30-X BD Falcon-60x10 Grainer - Petri 60x15 Corning-60x15 mm Willco 60x15 Figure 13.

  • Page 11: Working With 1X3'' And 1X2'' Chamber Slides - Magnetic Locks

    User Manual H301-NIKON-NZ100/200/500-N Rev 03 7. Working with 1x3’’ and 1x2’’ chamber slides - magnetic locks Magnetic locks prevent movement of 1’’x 3’’ and 1’’x 2’’ chamber slides inside of the sample holder. NOTE: Magnetic locks are included with sample holder.

  • Page 12: Working With Mw Plates - Magnetic Locks And Chamber Riser

    A single silicon tubing carries output gas from the Okolab Gas Controller to the H301-NIKON-NZ100/200/500-N. Silicon tubing connects to a gas input - brass opening - located on a corner of the H301-NIKON-NZ100/200/500-N. See Figure 18. Connect by gently pushing silicon tubing onto brass opening.

  • Page 13: Working With Perfusion

    10. Working with Perfusion The Chamber Riser included with H301-NIKON-NZ100/200/500-N features 12 perfusion holes for the insertion of perfu- sion tubing up to 2.5 mm in outer diameter. To lock the Chamber Riser into the base use a 1.5mm Allen key to secure the 4 GUTB2-2,5-6 screws as shown in Figure 19.
  • Page 14 User Manual H301-NIKON-NZ100/200/500-N Rev 03 Perfusion dedicated opening 1.Frontal view 2.3D view Figure 20. Perfusion. Figure 21. How to access the perfusion holes. NOTE: Working with Perfusion is possible with Mad City Labs NZ100/200 ONLY www.oko-lab.com...

  • Page 15: Microfluidic-C-Riser (Optional)

    The MICROFLUIDIC-C-RISER is a chamber riser with 19x3 mm windows (on the two short sides) to allow insertion of microfluidic tubings. Windows are magnetically closed. Compatible with most of H201 and H301 Okolab chambers. Thickness of this chamber riser is 8mm (2mm more than default chamber riser). Requires Koehler lid and single ac- commodation specimen holders.

  • Page 16: Connection Of The Chamber With Z Piezo Stage

    User Manual H301-NIKON-NZ100/200/500-N Rev 03 11. Connection of the Chamber with Z Piezo stage Follow the steps shown in the images of Figure 23 and listed below in order to correctly connect the chamber with Z piezo stage. Place the chamber on the stage and tighten 2 captive screws (See Image 2 of Figure 23). Captive screws housings are indicated with letter B in Image 2 of Figure 23.

  • Page 17: Cleaning

    User Manual H301-NIKON-NZ100/200/500-N Rev 03 12. Cleaning • Turn the system off and pull the mains plug out the socket • Remove the lid from the chamber main body, and keep it separate from the chamber main body while the chamber cools down.

This manual is also suitable for:

Nz100/200/500-n

Table of Contents