FUTABA R7114SB Quick Start Manual

1M23N36202
R7114SB
Thank you for purchasing a Futaba R7114SB FASSTest-2.4GHz compatible receiver. The R7114SB receiver features bi-directional communication with a FASSTest
Futaba transmitter using the S.BUS2 port. Using the S.BUS2 port an impressive array of telemetry sensors may be utilized. It also includes both standard PWM output
ports and S.BUS output ports. The R7114SB can also be switched to the FASST-Multi-ch System.
Applicable systems: Futaba FASSTest-2.4GHz / FASST-Multi-ch system transmitter
●
Usage precaution
• Analog servos cannot be used with the R7114SB in the FASSTest
12CH mode.
• When the FASST Multi-ch High-speed Mode is used, analog servos
cannot be used at the CH1 〜 6 outputs for convention systems. How-
ever, in other than the FASSTest 12CH mode, analog servos can be
used at CH7-12, DG1 and DG2 at any time.
• Don't connect to Extra Voltage Telemetry Port before turning on a re-
ceiver.
WARNING
Changes or modification not expressly approved by the party
responsible for compliance could void the userʼ s authority to operate the
equipment.
The R7114SB receiver should be protected from vibration by foam
rubber, Velcro, or similar mounting methods. Protect from moisture.
Antenna installation precaution
Do not cut or bundle the receiver antenna wire.
Do not bend the coaxial cable. It causes damage.
The antennas must be mounted in such a way to assure they are strain
relieved.
Keep the antenna as far away from the motor, ESC and other noise
sources as you possibly can.
Be sure that the two antennas are placed at 90 degrees to each other.
Do not bend the antenna part
Fix the sleeve to the model
Gently bend the coaxial
cable part.
90°
Antenna
installation
LED Indication
System Mode LED Status
No signal reception
Green
Receiving signals
FASSTest
Solid
Waiting for link
No signal reception
Receiving signals
FASST Off
Receiving signals but ID is unmatched
Waiting for link
FASSTest
−
Unrecoverable error (EEPROM, etc.)
FASST
supplied by an approved external power supply source suitable for use at minimum Tma 40°C whose
output meets LPS(or PS2), SELV(or ES1) and output is rated: 3.7Vdc to 7.4Vdc.
Compliance Information Statement (for U.S.A.)
This device, trade name Futaba Corporation, model number R7114SB, complies with part15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: To assure continued FCC compliance
to operate the equipment.
2. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
The responsible party of this device compliance is:
FUTABA Corporation of America
2681 Wall Triana Hwy Huntsville, AL 35824, U.S.A.
Phone:1-256-461-9399 FAX:1-256-461-1059 E-mail: service@futabaUSA.com
Declaration of Conformity (for EU)
Hereby, Futaba Corporation declares that the radio equipment type is R7114SB in compliance with Directive 2014/53/
EU. The full text of the EU declaration of conformity is available at the following internet address:
http://www.rc.futaba.co.jp/english/dl/declarations.html
◆ FASSTest-2.4GHz Bidirectional Communication System / FASST-Multi-ch 2.4GHz
◆ S.BUS2 / S.BUS Port and 12 Channels (+DG1,2) for Conventional System Receiver
◆ with High gain antenna
Connection
Link LED
Red Solid
Green Solid
Start → 2 seconds later →
Red Blink（1second）
Red Solid
Green Solid
Green Blink
Red Blink
Alternate blink
■ The R7114SB has two antennas. In order to maximize signal reception and
promote safe modeling Futaba has adopted a diversity antenna system. This allows
the receiver to obtain RF signals on both antennas and fly problem-free.
Antenna installation for carbon fuselage
You must leave 30mm at the tip of the antenna fully exposed. The
exposed antenna should be secured so that it cannot move around or
back inside of your aircraft.
Be careful of connector insertion
Don't connect an S.BUS servo / gyro to S.BUS2 connector.
Do not connect the power supply battery to other than the power
supply connector.
■ There is the danger of ignition, explosion, or burning.
Link precaution
Do not perform the linking procedure while the motor's main power is
connected or the engine is operating as it may result in serious injury.
When the linking is complete, please cycle the receiver power and
ensure the receiver is properly linked to the transmitter.
Please power up your system in this order. Transmitter first, followed
by the receiver.
If the R7114SB receiver was previously linked to another transmitter,
make sure that transmitter is not operating while linking the receiver to
the new transmitter.
R7114SB Specifications
FASSTest-2.4GHz system(14ch/12ch mode)
FASST-2.4GHz system (Multi-ch mode)
S.BUS2 and S.BUS port and Linear 12ch +Digital 2ch for conventional
system receiver
• Dual antenna diversity
• Size: 1.98 x 1.45 x 0.63 in. (50.2x37.0x15.9 mm)
• Weight: 0.77 oz. (21.9 g)
• Power requirement: 3.7 V to 7.4 V (Voltage range: 3.5 V to 8.4 V)
• Battery F/S Voltage: FASSTest:It sets up with a transmitter
FASST: 3.8 V *The Battery F/S voltage is set for 4-cell NiCd/NiMH bat-
tery. Battery F/S function doesn't work properly when other type battery
is used.
• Extra Voltage port: 0 V-70 V DC
Compliance Information Statement (for Canada)
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure
limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum dis-
tance 20cm between the radiator & your body.
French: Cet appareil radio est conforme au CNR-210 d'Industrie Canada. L'utilisation de ce dispositifest autorisée
seulement aux deux conditions suivantes : (1) il ne doit pas produire de brouillage, et (2) l'utilisateur du dispositif doit
être prêt à accepter tout brouillage radioélectrique reçu, même sice brouillage est susceptible de compromettre le fonc-
tionnement du dispositif. Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé.
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de ray-
onnement et votre corps.
低功率射頻器材技術規範 3.8.2 警語
取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率或變更
原設計之特性及功能。
低功率射頻器材之使用不得影響飛航安全及干擾合法通信 ； 經發現有干擾現象時，應立即停用，並改善至
無干擾時方得繼續使用。
前述合法通信，指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及
醫療用電波輻射性電機設備之干擾。
Connector
The direction of the
connectors of the
bottom 3 ports is