Subscribe to Our Youtube Channel
Summary of Contents for SifWeld ST180 PRO
- Page 1 Peters House The Orbital Centre Icknield Way Letchworth Garden City Hertfordshire SG6 1ET Tel. +44 (0) 845 130 7757 TI G SifWeld ST180 PRO Approved Operation Manual TSX1ST180...
- Page 2 Type of Equipment Welding power source for MMA/TIG welding Brand name or trade mark SifWeld® Type designation etc. ST180 PRO Manufacturer or his authorised representative established within the EEA Name, address, telephone no, fax no Weldability Sif Peters House, The Orbital Centre...
- Page 3 Safety Guidelines These general safety norms cover both arc welding machines and plasma cutting machines unless otherwise noted. The equipment must only be used for the purpose it was designed for. Using it in any other way could result in damage or injury and in breach of the safety rules. Only suitably trained and competent persons should use the equipment.
- Page 4 Wear suitable protective flame resistant clothing. The sparks and spatter from welding, hot work pieces, and hot equipment can cause fires and burns. Welding on closed containers, such as tanks, drums, or pipes, can cause them to explode. Accidental contact of electrode to metal objects can cause arcs, explosion, overheating, or fire.
- Page 5 LF Declaration Consult the data plate on the equipment for the power supply requirements. Due to the elevated absorbency of the primary current from the power supply network, high power systems affect the quality of power provided by the network. Consequently, connection restrictions or maximum impedance requirements permitted by the network at the public network connection point must be applied to these systems.
-
Page 6: Table Of Contents
Contents Preface General Introduction Technical Specifications Installation Front Panel Layout Operation Warranty... -
Page 7: Preface
For your own safety and that of your working environment, pay particular attention to the safety instructions in the manual. For more information on SifWeld products, consult an authorised SifWeld dealer, or visit the SifWeld web site at www.sifweld.com. The specifications presented in this manual are subject to change without prior notice. -
Page 8: Introduction
1.2 Introduction This welding machine adopts the latest pulse width modulation (PWM) technology and insulated gate bipolar transistor (IGBT) inverter technology whilst being portable, small in size, light weight, and with low consumption. The machine has excellent performance in MMA and TIG mode. In MMA mode the following can be controlled: arc starting current arc force and the welding current parameters also can be adjusted sepa- rately, the welding mode can select by “welding mode selective switch”... -
Page 9: Technical Specifications
1.3 Technical Specifications SifWeld ST180 PRO 1ph 230V±10% Power voltage (V) Frequency (Hz) 50/60 Rated input current (A) l-1 max 33.5 Rated input power (kw) 5-180 Rated current range (A) 5-180 Power factor 0.80 No load voltage (VRD) Duty cycle (%) 40˚C 10min 180Amps @ 35 % ≥80%... -
Page 10: Installation
2. Installation Unpacking Check the packaging for any signs of damage. Carefully remove the machine and retain the packaging until the installation is complete. Location The machine should be located in a suitable position and environment. Care should be taken to avoid moisture, dust, steam, oil or corrosive gases. -
Page 11: Front Panel Layout
2.1 Front Panel Layout Front View Power source front panel layout 1. Control knob 2. LED Display 3. Welding Power Output Socket (+) 4. Welding Power Output Socket (-) 5. Alarm LED 6. Power LED 7. Hot start LED 8. Arc force LED 9. - Page 12 MMA welding Insert the cable plug with electrode holder into the “+” socket on the front panel of the welding machine, and tighten it clockwise. Insert the cable plug of the work return lead into the “-” socket on the front panel of the welding machine, and tighten it clockwise.
-
Page 13: Operation
3. Operation Before starting any welding activity ensure that you have suitable eye protection and protective clothing. Also take the necessary steps to protect any personnel within the area. ST180PRO 1. Control knob 4. Arc force LED 2. LED display 5. - Page 14 Operating Environment • Operation temperature range -10°C~+40°C. • Relative humidity is below 90 % (20°C). • Protect the machine against heavy rain or in hot circumstance against direct sunshine. • The content of dust, acid or corrosive gas in the surrounding air or substances can not exceed normal standard.
-
Page 15: Warranty
Weldability Sif or an Authorised SifWeld Service Centre, in order to maintain validity of the extended warranty. Service visits can be booked online at www.sifweld.com or by calling 0870 330 7757 and will be charged at an average of £65 net per hour of travel/ servicing time. - Page 16 ® Peters House, The Orbital Centre, Icknield Way, Letchworth Garden City, Hertfordshire, SG6 1ET Tel. +44 (0) 845 130 7757 | Fax. +44 (0) 800 970 7757 | Email. sales@weldability-sif.com | www.sifweld.com www.sifweld.com...
Need help?
Do you have a question about the ST180 PRO and is the answer not in the manual?
Questions and answers