Advertisement
Quick Links
Vettis™
Model/Modelo/Modèle
Write purchased model number here.
Escriba aquí el número del modelo comprado.
Inscrivez le numéro de modèle ici.
Read all instructions prior to installation.
Lea todas las instrucciones antes de
hacer la instalación.
Veuillez lire toutes les instructions avant
l'installation.
For product & installation questions, do not return to the store. For additional help, contact customer service.
Si tiene preguntas sobre el producto y su instalación, no acuda a la tienda. Para ayuda adicional, comuníquese con el departa-
mento de servicio al consumidor.
Si vous avez des questions au sujet du produit et de l'installation, ne retournez pas au magasin. Pour obtenir de l'aide, commu-
niquez avec le service à la clientèle.
www.brizo.com
SINGLE HANDLE LAVATORY AND
92169
VESSEL FAUCETS
LLAVES DE AGUA DE UNA MANIJA
PARA LAVAMANOS Y ARTESAS
ROBINETS À UNE MANETTE POUR
LAVABO ET CUVETTE
1
65086LF▲
?
www.brizo.com
1-877-345-BRIZO (2749)
brizosupport@brizo.com
01/31/2019 Rev. B
Advertisement
Related Manuals for Brizo Vettis 65086LF
Summary of Contents for Brizo Vettis 65086LF
- Page 1 Si tiene preguntas sobre el producto y su instalación, no acuda a la tienda. Para ayuda adicional, comuníquese con el departa- mento de servicio al consumidor. 1-877-345-BRIZO (2749) Si vous avez des questions au sujet du produit et de l’installation, ne retournez pas au magasin. Pour obtenir de l’aide, commu- brizosupport@brizo.com...
- Page 2 You may need: Optional/Optional/Optional Usted puede necesitar: Articles dont vous pouvez avoir besoin: 3/32” (2.5 mm) Add optional temperature ring by removing cap button (1), set screw (2), handle (3) and bonnet cap (4). Install temperature ring (5), ensure that ring is aligned with the open notch on faucet.
- Page 3 SEALANT OVERTIGHTEN SELLADORES APRIETES DEMASIADO PRODUITS D’ÉTANCHÉITÉ TROP SERRER NOTE: If you determine the PEX supply tubing for this faucet is too long and must be shorter to create an acceptable installation, follow the instruction for Custom Fit Connections. NOTE: If you determine the PEX supply tubing for this faucet is too long and must be shorter to create Tighten one additional turn with wrench.
- Page 4 METAL POP-UP / DESAGÜE AUTOMÁTICO DE METAL / RENVOI MÉCANIQUE EN MÉTAL Remove stopper and flange. Screw nut all the way down. Push washer and gasket down. Apply silicone to underside of flange. Insert body into sink. Screw flange into body. Pivot Remove tailpiece from body, add plumber tape, replace tailpiece.
- Page 5 CUSTOM FIT CONNECTIONS / CONEXIONES ESPECIALES / SPÉCIAUX TUYAUTERIE BRANCHEMENT Installer accepts the responsibility to cut supply tubing in a way that allows a leak-free joint to be created. Brizo is not responsible for tubing that is cut too short or cut in a way that will not allow for a leak-free joint. Must use RP50952 sleeves supplied with model and nuts included on supply lines.
-
Page 6: Maintenance
Maintenance If faucet exhibits very low flow: Turn on hot and cold water supplies and check all connections at arrows for leaks. Retighten if necessary, but do not overtighten. A. Remove and clean flow filter (8), or remove debris from flow restrictor (7). B. - Page 7 Vettis™ RP92354 RP92347 Lift Rod & Finial Model/Modelo/Modèle O-Rings (2) Barra de Alzar y Pomo Juntas tóricas (2) 65086LF▲ Tige de Manoeuvre et Joints toriques (2) Grain de la Tirette RP92346 Aerator Aireador Aérateur RP92349 RP92353▲ RP92348 Valve Cartridge Handle Assembly Chamber Assembly Cartucho de la Válvula Ensamble de la Manija...
- Page 8 RESULTING FROM REASONABLE WEAR AND TEAR, OUTDOOR USE, MISUSE (INCLUDING USE OF THE are not covered by this warranty. Brizo Kitchen & Bath Company shall not be liable for any damage to the product PRODUCT FOR AN UNINTENDED APPLICATION, FREEZING WATER, ABUSE, NEGLECT OR IMPROPER...