Advertisement
5. hYDRAuLIC SYSTEm puRGING
5.1.
Open the release valve by turning it one full turn counter-clockwise.
5.2.
Pump the handle a minimum eight full strokes.
5.3.
Close the release valve by turning it clockwise.
6. OpERATION
WARNING! Before use ensure you have read, understood and applied Section 1
‰
safety precautions.
ImpORTANT: Before use, the operator is to visually inspect the jack for cracked
welds, damaged or missing parts or hydraulic leaks.
6.1.
RAISING A VEhICLE
The effort of raising the rated load shall be reduced by the use of additional persons.
6.2.
Ensure that the jack and the vehicle are on a hard, level surface.
6.2.1.
Always ensure that the vehicle handbrake is engaged and that the vehicle wheels
are chocked.
6.2.2.
Consult the vehicle manual to determine the location of jacking points.
6.2.3.
Position the jack under a suitable lifting point.
6.2.4.
Turn the release valve clockwise, to the closed position (Fig.3).
DO NOT over-tighten.
8
6.2.5.
Raise the vehicle to the desired height by pumping the handle up and down.
6.2.6.
Place axle stands beneath the locations recommended by the vehicle manufacturer.
6.2.7.
Turn the release valve slowly counter-clockwise to lower the vehicle on to the axle
stands.
6.3.
LOWERING A VEhICLE
6.4.
Turn the release valve clockwise to the closed position.
6.4.1.
Pump the handle to raise the vehicle off the axle stands.
6.4.2.
Remove the axle stands from beneath the vehicle.
6.4.3.
Turn the release valve slowly counter-clockwise to lower the vehicle to the ground.
NOTE: When not in use, ALWAYS leave the saddle and ram fully retracted.
7. mAINTENANCE
ImpORTANT: Only fully qualified personnel should attempt maintenance or repair.
mONThLY mAINTENANCE
7.1.
Lubrication is critical to jacks. Any restriction due to dirt or rust can cause either slow
or extremely rapid jack movement, causing damage to the internal components.
To keep the jack well lubricated, carry out the following steps.
7.1.1.
Lubricate the ram, the linkages and the saddle and pump mechanism with light oil.
7.1.2.
Grease the wheel bearings and axles.
7.1.3.
Keep all jack surfaces and warning labels clean.
7.1.4.
Check and maintain the ram oil level (Section 7.3).
7.2.
ThREE mONThLY mAINTENANCE
7.2.1.
At three monthly intervals, check the ram for any signs of rust or corrosion. Clean the
ram as required and wipe with an oiled cloth.
7.3.
ChECKING ThE OIL LEVEL
7.3.1.
Fully retract the ram by turning the release valve counter-clockwise.
7.3.2.
With the jack in the level position, remove the oil filler plug (Fig.4).
7.3.3.
The oil should be level with the bottom of the oil filler hole. If it is not, top up with clean hydraulic jack oil.
7.3.4.
Replace the oil filler plug and check the jack operation.
7.3.5.
Purge air from the hydraulic unit as required. Refer to Section 5.
NOTE: Always store the jack in the fully lowered position. This will protect critical areas from excessive corrosion.
Owing to their size and weight, hydraulic products should ideally be repaired by local service agents. We have service / repair agents in
most parts of the UK. Before returning your product please call our technical helpline on 01284 757505 for advice and troubleshooting
guidance. If the jack is under guarantee please contact your stockist.
ENVIRONmENT pROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk business park, bury St Edmunds, Suffolk. Ip32 7AR
01284 757500
© Jack Sealey Limited
01284 703534
sales@sealey.co.uk
Original Language Version
Fig.2
Fig.3
Fig.4
www.sealey.co.uk
3040A.V2 Series
Issue:1- 04/12/18
Advertisement
