bioBidet BioMIST EM-307 Owner's Manual

Bidet cleaner

Advertisement

BIDET
CLEANER
MODEL EM-307
Owner's Guide
Please read all instructions before use.
KEEP YOUR RECEIPT FOR WARRANTY PURPOSES.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BioMIST EM-307 and is the answer not in the manual?

Questions and answers

Summary of Contents for bioBidet BioMIST EM-307

  • Page 1 BIDET CLEANER MODEL EM-307 Owner’s Guide Please read all instructions before use. KEEP YOUR RECEIPT FOR WARRANTY PURPOSES.
  • Page 2: Important Safety Instructions

    7. Do not operate unit with a damaged power cord or if the unit has been dropped or damaged. To avoid risk of electrical shock, do not disassemble unit; contact Biobidet Customer Support for examination and repair. Incorrect reassembly can cause a risk of electrical shock when unit is used.
  • Page 3 19. Always allow Handheld Steam Cleaner to cool (at least 30 minutes for complete cooling) and empty Boiler before storing. SAVE THESE INSTRUCTIONS! FOR HOUSEHOLD USE ONLY Questions or comments? • www.biobidet.com • support@biobidet.com • 877-339-5214 Speak your mind! We invite you to review this product online: www.biobidet.com/reviews...
  • Page 4: Product Information

    Product Information The following features and accessories are included with your Handheld Steam Cleaner. Carefully inspect the packing material for all parts listed below. To obtain possible missing parts, refer to Product Support on Page 14 of this manual for Consumer Service contact information. 1.
  • Page 5 • The Steam Aperture Steam Button is pressed and held. Either the Jet Nozzle or Wide Nozzle should always be connected to the Steam Aperture when the unit is in use. • The Boiler Cap (2) is designed to safely contain steam inside the Boiler. The Boiler Cap must Boiler with water.
  • Page 6 Assembling Your Handheld Steam Cleaner CONNECTING JET NOZZLE / WIDE NOZZLE WARNING: DO NOT attempt to connect any accessories while unit is emitting steam. Doing so could result in burns or other injury. 1. Insert cylinder on back of Jet Nozzle or Wide Nozzle (FIGURE 1-A) into opening of Steam Aperture .
  • Page 7 CONNECTING UTILITY BRUSHES NOTE: Both Nylon Utility Brushes and the Brass Utility Brush are all attached in the same manner. 1. Begin by aligning hexagonal-shaped hole on back of Utility Brush (FIGURE 3-A) with hexagonal tip of Jet Nozzle (FIGURE 3-B). 2.
  • Page 8 Assembling Your Handheld Steam Cleaner CONNECTING SQUEEGEE 1. Connect Squeegee to Wide Nozzle by inserting hook tabs on Squeegee (FIGURE 4-A) into slots on Wide Nozzle (FIGURE 4-B). 2. Swing Squeegee backwards until hook latch on back snaps over tab on top of Wide Nozzle. 3.
  • Page 9: Filling With Water

    Using Your Handheld Steam Cleaner FILLING WITH WATER 2. Make sure power cord is unplugged from electrical outlet. 3. Cautiously remove Boiler Cap by unscrewing it in a counter-clockwise direction, and lift it off. 4. Boiler should always be emptied after each use. If it was not emptied after the previous use, 5.
  • Page 10: Steam Cleaning

    Using Your Handheld Steam Cleaner STEAM CLEANING NOTE: Before operating, make sure all desired accessories are connected and Boiler is power cord into a convenient 3-prong electrical outlet. Heating Indicator Light will illuminate to show that unit is receiving power and Boiler has begun to heat. CAUTION: This unit uses a grounded (3-prong) electrical plug.
  • Page 11: Storage & Care

    Storage & Care PROPER STORAGE your steaming tasks, follow the steps listed below. 1. Unplug power cord from electrical outlet. 2. Allow unit to cool (30 minutes for complete cooling). 3. Press and hold Steam Button to release any remaining steam pressure. 4.
  • Page 12: Troubleshooting

    Troubleshooting PROBLEM POSSIBLE CAUSE SOLUTION Unit fails to heat up and begin Unit is not plugged in. Plug power cord into electrical outlet. steaming. Heating Indicator Light Household circuit breaker / ground Reset circuit breaker / ground fault DOES NOT illuminate. fault interrupter has tripped or blown interrupter, or replace fuse.
  • Page 13: Product Support

    For problems with your Handheld Steam Cleaner, please refer to the troubleshooting guide located on Page 12 of this manual. Additional inquiries should be directed to our consumer support services through our Web site, www.biobidet.com. If you do not have internet access, you may also contact our Customer Support Department by telephone, at 877-339-5214.
  • Page 14: Warranty Information

    (1) year from the date of purchase. If any such defect is discovered within the warranty period, Biobidet, at its discretion, will repair or replace the Product at no cost if the Product is returned to Biobidet postage-paid. Repairs not covered by the warranty or outside the warranty period will require a fee to cover the cost of materials, handling and shipping.
  • Page 16 BIDET CLEANER review this product online www.biobidet.com/reviews BBC Innovation corp 7900 S IL Route 31 Crystal Lake IL 60014 U.S.A W: www.biobidet.com | P: 877-339-5214 E: support@biobidet.com...

Table of Contents

Save PDF