Tables - ABB HT602839 Operation Manual

Operation Manual / A150-M56/66/57/67 - A155-M..

Tables

Table 1: Definition of pictograms ............................... 9
Table 2: Personal protective equipment to be worn
at all times ...................................................................... 14
Table 3: Personal protective equipment to be worn
specific to the respective task ................................... 14
Table 4: Weight of complete turbocharger unit .... 29
Table 5: Fitting the turbocharger, value X, L........... 35
Table 6: Torque-controlled tightening of the pres-
sure screws .................................................................... 37
Table 7: Lubricating oil pressure at oil inlet before
turbocharger ................................................................. 44
Table 8: Lubricating oil temperature at the inlet... 45
Table 9: Maximum lubricating oil temperature at the
outlet .............................................................................. 45
Table 10: Tightening torque (86505)........................ 49
Table 11: Expected replacement intervals ............... 55
Table 12: Maintenance table....................................... 58
Table 13: Parameters for wet cleaning of com-
pressor ............................................................................ 61
Table 14: Turbine wet cleaning, recommended oper-
ating state ..................................................................... 64
Table 15: Wet cleaning of turbines, parameters for 1-
nozzle cleaning.............................................................. 65
Table 16: Wet cleaning of turbines, parameters for 6-
nozzle cleaning.............................................................. 66
Table 17: Value table for soaking................................ 73
Table 18: Tightening torque (81152 / 81154)............ 77
Table 19: Malfunctions when starting - Delayed
start-up .......................................................................... 78
Table 20: Malfunctions when starting - Vibrations 78
Table 21: Malfunctions when starting - Rubbing of
rotating parts................................................................ 78
Table 22: Malfunctions during operation - Lubricat-
ing oil pressure too low............................................... 79
Table 23: Malfunctions during operation - Speed re-
duces............................................................................... 79
Table 24: Malfunctions during operation - Speed in-
creases ........................................................................... 79
Table 25: Malfunctions during operation - Exhaust
gas temperature too high .......................................... 80
© Copyright 2021 ABB. All rights reserved.
Tables
Table 26: Malfunctions during operation - Charge air
pressure too low ............................................................ 80
Table 27: Malfunctions during operation - Charge air
pressure too high .......................................................... 81
Table 28: Malfunctions during operation - Engine
performance losses....................................................... 81
Table 29: Malfunction - Turbocharger pumping ..... 82
Table 30: Malfunction - Sporadic surge blows ........ 82
Table 31: Malfunctions when stopping - Runout
noises ............................................................................... 83
Table 32: Malfunctions when stopping - Runout time
too short.......................................................................... 83
Table 33: Malfunction of the speed measurement
system - No signal or poor signal amplitude .......... 84
Table 34: Malfunction of the speed measurement
system - Measured speed too high ........................... 84
Table 35: Malfunction of the speed measurement
system - Measured speed too low............................. 84
Table 36: Swivel lifting eyes......................................... 86
Table 37: Press-off screws ........................................... 87
Table 38: Dismantling screw ....................................... 87
Table 39: Weights of assemblies ................................ 92
Table 40: Tightening torques...................................... 93
Table 41: Tightening torques for insulation............. 94
Table 42: 3 press-off screws...................................... 101
Table 43: 6 press-off screws ..................................... 102
Table 44: Tightening torque (90012-01) ................. 107
Table 45: Permissible clearances A and B ................ 112
Table 46: Nozzle ring compression PD ..................... 113
Table 47: Tightening torque (90012-01)................... 116
Table 48: Tightening torque (51007) ........................ 117
Table 49: Tightening torque (79041) ........................ 118
Table 50: Tightening torque (72011) ........................ 119
Table 51: Permissible clearances N and R ............... 122
Table 52: Tightening torque (51009) ....................... 125
Table 53: Tightening torque (51009) ....................... 126
Table 54: Tightening torque (72051)........................ 128
HZTL4032_EN Revision Q January 2021