Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for xpr B100PROX-MF
- Page 1 B100PROX-MF V1 Biometric Mifare Reader USER’S MANUAL www.xprgroup.com...
-
Page 2: Table Of Contents
CONTENTS 1. DESCRIPTION 2. SPECIFICATIONS 3. MOUNTING 4. WIRING 5. CONNECTING BIOMETRIC READERS TO EWS CONTROLLER 5.1 CONNECTING BIOMETRIC READERS IN SAME RS-485 LINE WITH THE EWS CONTROLLERS 5.2 CONNECTING BIOMETRIC READERS WHEN ALL THE CONTROLLERS HAVE TCP/IP COMMUNICATION 5.3 RS-485 TUNING 6. -
Page 3: Description
1. DESCRIPTION B100PROX-MF V1 is a Wiegand biometric and proximity reader for access control applications with programmable wiegand output. It offers storage of up to 100 fingerprints, it reads Mifare Classic 1K & 4K, Ultralight, Desfire cards/tags and has a programmable Wiegand Output (8 to 128 bits). -
Page 4: Mounting
(fitted with additional heater if very low temperature) to keep a constant sensor level performance. XPR™ cannot guarantee the functionality of the product if measures and advice before are not followed. -
Page 5: Connecting Biometric Readers To Ews Controller
5. CONNECTING BIOMETRIC READERS TO EWS CONTROLLER - The Biometric readers can be connected to virtually any controller that conforms to Wiegand format standards (standard Wiegand 26bit or self-defined Wiegand). - The lines D0 and D1 are the Wiegand lines and the Wiegand Number is sent through them. - The RS-485 line (A, B) is used for fingerprint transfer and reader settings. -
Page 6: Connecting Biometric Readers When All The Controllers Have Tcp/Ip Communication
5.2 CONNECTING BIOMETRIC READERS WHEN ALL THE CONTROLLERS HAVE TCP/IP COMMUNICATION 150m 150m 150m max. max. max. •When all the controllers are connected via TCP/IP, then the RS-485 network becomes local (from Reader 1 to the Controller then to the Reader 2). •Connect the readers directly to the RS-485 terminals in each controller. -
Page 7: Connecting Biometric Readers To 3Rd Party Controller
6. CONNECTING BIOMETRIC READERS TO THIRD PARTY CONTROLLERS • Connect the lines D0, D1, Gnd and +12V to the third party controller. • Connect the RS-485 Line (A, B) to the converter. Connect the converter in the PC. • Fingerprint enrollment is done from the PC Software. Connection between the Biometric readers and the PC must be established. -
Page 8: Configuring The Biometric Readers In Pros Cs Software
8. CONFIGURING THE BIOMETRIC READERS IN PROS CS SOFTWARE 8.1 ADDING BIOMETRIC READER 1. Expand the Door item to view the readers 2. Right click on the reader and select properties (8.1) 3. In the Basic tab, for “Type” of the Reader select “B100-MF”. (8.2) 4. -
Page 9: Enrolling Fingerprints From A Reader
8.2 ENROLLING FINGERPRINTS FROM A READER 1. Open the Users Window and create a new user. Click on “New User”, put a name and ID(card number). (8.7) 2. Go to the “Biometric” Tab 3. Select the reader(with left click) from which the enrollment will be done. (8.8) 4. -
Page 10: Enrolling Fingerprints From Desktop Reader
8.3 ENROLLING FINGERPRINTS FROM DESKTOP READER 1. Open the Users Window and create a new user. Click on “New User”, put a name and ID(card number). (8.7) 2. Go to the “Biometric” Tab 3. Select the USB desktop Reader (with left click).. (8.13) 4. -
Page 11: Deleting Fingerprints
8.4 DELETING FINGERPRINTS In General, the fingerprints are stored in the Biometric reader and in the Software. Deleting can be done only in the readers or from both places. Deleting one user from the biometric reader Select the User Click on “Delete User”. The User together with its fingerprints will be deleted from both the software and the fingerprint readers. -
Page 12: Firmware Update
8.6 FIRMWARE UPDATE Right-click on the reader and select Firmware update menu (8.18) On the Firmware update window, click on the Browse button (8.19). The default location of the firmware files installed with PROS CS is in the folder “Firmware”. Select the firmware file with a “xhc”... -
Page 13: Entry Mode
8.9 ENTRY MODE 8.9.1 CARD OR FINGER Right click on the biometric reader Select “Properties” and go to the “Biometric” For Entry Mode select “Card or Finger” (8.20) Note: All the fingers and the card will send the same wiegand number (8.21) 8.9.2 CARD AND FINGER Right click on the biometric reader Select “Properties”... -
Page 14: Finger On Card
8.9.4 FINGER ON CARD Right click on the biometric reader Select “Properties” For “type” of the reader select “B100-MF FOC” (8.30) Writing Template on the card 1. Open Users window 2. Select existing user or create new one 3. Enroll 1 or 2 fingers using B100PROX-USB Desktop Biometric Reader 4. -
Page 15: Configuring The Biometric Readers In Biomanager Cs
9. CONFIGURING THE BIOMETRIC READERS IN BIOMANAGER CS BIOMANAGER CS is software for fingerprint management of XPR Biometric readers, when used with third party access controllers. Main functions: - Fingerprint Enrollment It can be done by ANY Biometric reader in the network or by Desktop (USB) Biometric reader. -
Page 16: Edit Reader
If reader is online, new line is added on top of the event table If reader is not online, following line is added on top of the event table If reader is online, right click on reader and select Upload configuration Check at event table if configuration was successful 9.3 EDIT READER Right-click on the reader and select Properties... -
Page 17: Add User
9.5 ADD USER 1. Open the Users Window and create a new user. Click on “New User”, put a name and ID(card number). (8.7) 2. Select the reader(with left click) from which the enrollment will be done. (8.8) 3. Right click on the fingertip and select enroll. (8.9) 4. -
Page 18: Deleting Fingerprints
9.6 DELETING FINGERPRINTS In General, the fingerprints are stored in the Biometric reader and in the Software. Deleting can be done only in the readers or from both places. Deleting one user from the biometric reader Select the User Click on “Delete User”. The User together with its fingerprints will be deleted from both the software and the fingerprint readers. -
Page 19: Custom Wiegand
9.8 CUSTOM WIEGAND BIOMANAGER CS has defined Wiegand 26, 30, 34, 40 bit as standard options and other 3 Wiegand settings as user definable. To setup custom Wiegand format Select Wiegand menu from Settings At Wiegand setup window select one from customs Wiegand Set Wiegand parameter Click on Save button Note:... -
Page 20: Wiegand Protocol Description
10. WIEGAND PROTOCOL DESCRIPTION The data is sent over the lines DATA 0 for the logic “0” and DATA 1 for the logic “1”. Both lines use inverted logic, meaning that a pulse low on DATA 0 indicates a “0” and a pulse low on DATA 1 indicates a “1”.When the lines are high, no data is being sent. Only 1 of the 2 lines ( DATA 0 / DATA 1 ) can pulse at the same time.