Advertisement
Quick Links
Tilting, Swiveling & Rotating
• Supports most 40"- 80" Flat Panel TVs
• Maximum Weight Capacity: 132 lbs.
• Supports VESA Sizes up to 600x500
For technical assistance or troubleshooting
This product Wall Mount frame is intended for use only with an apparatus which has a maximum weight of 132 lbs. See apparatus
instructions. Using with an apparatus heavier than the maximum weight indicated may result in instability and cause possible
injury.
READ THIS FIRST
Read this entire manual! Do not attempt to install this product if you do not understand the instructions. Contact a qualified
mount installer if you have any doubts about a safe and secure mount installation, or if you are not sure what specific wall
materials you are attaching this mount to. Check all the parts carefully to make sure there are no missing or damaged parts.
Improper installation may result in damage to your TV, property, and personal injury.
Flat Panel Wall Mount
Model: A675STS
please call
+5 to -5
1-800-936-1168
+5 to -15
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Atec A675STS
Summary of Contents for Atec A675STS
- Page 1 Tilting, Swiveling & Rotating Flat Panel Wall Mount Model: A675STS +5 to -15 +5 to -5 • Supports most 40”- 80” Flat Panel TVs • Maximum Weight Capacity: 132 lbs. • Supports VESA Sizes up to 600x500 For technical assistance or troubleshooting...
- Page 2 Schoenfeld International Inc. and ATEC are not responsible for personal injury or product damage due to mishandling, incorrect mounting, incorrect assembly, or incorrect use of this product.
- Page 3 -Level Bracket Wall Mount Allen Wrench with Phillips End Security Bracket Clamps Mounting Plate Side Pieces Long Bolt Security Bracket Side Piece Washers Clamp Screws Screws Concrete Anchors M5x12mm Long Bolts M6x25mm bolts Wall Mount M6x40mm bolts Brackets M8x25mm Bolts Security Bracket Clamps M8x45mm Bolts Allen Wrench...
- Page 4 Step 1: Attach the side pieces to the mounting plate Slide the Mounting Plate Side Pieces (5) onto the ends of the Wall Mount (1). Secure the Mounting Plate Side Pieces (5) to the Wall Mount (1) using the Allen Wrench and the Side Piece Screws (S).
- Page 5 Step 2: Attach the left and right brackets to your TV Do not force the bolts into the mounting holes on your TV. Do not use an electric drill to tighten these bolts on your TV. This could damage the equipment or cause personal injury. CAUTION: Do not place the TV face down on a hard surface when installing the mounting plate on the TV.
- Page 6 Attach the TV Bracket to the rear of the TV cont’d If your television has a curved back, and the mounting holes are recessed (Fig 1b) spacers are required. Install the proper size Spacers (L-M) between the TV rear and the bracket structure as shown in Fig 1b.
- Page 7 Step 3: Find and mark the best position for the wall mount on the wall Step 4: Attach the wall mount to the wall...
- Page 8 1. Use a pencil, awl, or a nail to mark the location of the wall stud centers (Fig 3a) after locating the stud with an electronic stud locator. The distance between the marks should not be less than 16 inches (Studs must not be less than 16 inches (40.6cm) 2.
- Page 9 2.5” (65mm) Concrete wall Fig. 3e Fig. 3d Fig.3f Step 5: Hang the television display A large television requires two people to lift. Schoenfeld International Inc. and ATEC are not responsible for equipment damage or personal injury due to mishandling.
- Page 10 1. Lift the Television display with the brackets attached and carefully hang the top hook of the Brackets (2) over the top bar of the Wall Mount (1) as shown in (Fig. 4a). Carefully swing the display down so the lower part of the Brackets (2) fit over the lower bar of the Wall Mount (1). 2.
- Page 11 Step 6: Adjusting the Tilt 1. The Handle on the front of the Wall Plate mount arm is used to adjust the tilt angle of the TV to your desired angle as shown in (Fig. 5d). 2. This handle is a tension lever. To loosen the tilt adjustment, turn the handle counterclockwise until the handle hits the Wall Plate (1) and can turn no more.
- Page 12 Step 8: Adjusting the Rotation 1. If necessary, the TV can be rotated from -5° to +5° by adjusting the two screws on the rear of the Wall Plate (1) as shown in Fig. 5c. 2. To adjust the rotation, loosen these two screws with the Allen Wrench (4) about 1/2 turn each, and gently slide the TV to the left or right depending on your needs.
- Page 13 We warrant this product to you, the original purchaser at the time of purchase printed on a dated store receipt from an authorized ATEC retailer and for a period of six-years thereafter that our wall mount product and all it’s parts and components are free of defects in material and workmanship under normal use.
Need help?
Do you have a question about the A675STS and is the answer not in the manual?
Questions and answers