Table of Contents
Advertisement
Quick Links
Manual
iBASE
IB898
The information contained in this document has been carefully researched and is, to the best of our
knowledge, accurate. However, we assume no liability for any product failures or damages, immediate or
consequential, resulting from the use of the information provided herein. Our products are not intended for
use in systems in which failures of product could result in personal injury. All trademarks mentioned herein
are property of their respective owners. All specifications are subject to change without notice.
Advertisement
Chapters
Table of Contents
Related Manuals for Fortec Star iBASE IB898
Summary of Contents for Fortec Star iBASE IB898
- Page 1 Manual iBASE IB898 The information contained in this document has been carefully researched and is, to the best of our knowledge, accurate. However, we assume no liability for any product failures or damages, immediate or consequential, resulting from the use of the information provided herein. Our products are not intended for use in systems in which failures of product could result in personal injury.
- Page 2 IB898 Intel Atom E3800 SoC Series ® 3.5” Disk Size SBC USER’S MANUAL Version 1.0...
- Page 3 Acknowledgments AMI BIOS is a trademark of American Megatrends Inc. PS/2 is a trademark of International Business Machines Corporation. Intel and Atom are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. Nuvoton is a registered trademark of Nuvoton Technology Corporation.
-
Page 4: Table Of Contents
Table of Contents Introduction ............1 Product Description............. 1 Specifications ..............2 Checklist ................3 Board Dimensions ............... 4 Installations ............5 Installing the Memory ............6 Setting the Jumpers ............. 7 Connectors on IB898 ............11 BIOS Setup ............21 Drivers Installation ........ - Page 5 This page is intentionally left blank. IB898 User’s Manual...
-
Page 6: Introduction
INTRODUCTION Introduction Product Description ® Intel Atom IB898 is a 3.5-inch single board computer based on the E3800 series processors. It supports One DDR3L SODIMM sockets for a maximum memory capacity of 4GB. ® IB898 features the Intel Gen7 w/4EUs graphics engines and has both CRT and DisplayPort video display interface, and 24-bit LVDS dual channel interface with the use of the NXP PTN3460 device. -
Page 7: Specifications
INTRODUCTION Specifications Product Name IB898 [default silk screen model # on PCB is IB898] Form Factor 3.5” disk size SBC SoC Type/Speed Intel® Atom DC E3825 /1MB cache/1.33 GHz (IB898-I25) Intel® Atom SC E3815 /512KB cache/1.46 GHz (IB898-I15) FCBGA1170,Type-3, 25mmx27mm, 22nm,Tj= -40ﾟC to +110ﾟC ; **All SoC Skus will be on D-0 stepping »... -
Page 8: Checklist
INTRODUCTION Checklist Your IB898 package should include the items listed below. The IB898 SBC This User’s Manual 1 CD containing chipset drivers and flash memory utility IB898 User’s Manual... -
Page 9: Board Dimensions
INTRODUCTION Board Dimensions IB898 User’s Manual... -
Page 10: Installations
INSTALLATIONS Installations This section provides information on how to use the jumpers and connectors on the IB898 in order to set up a workable system. The topics covered are: Installing the Memory ................6 Setting the Jumpers ................7 Connectors on IB898 ................11 IB898 User’s Manual... -
Page 11: Installing The Memory
INSTALLATIONS Installing the Memory The IB898 board supports one DDR3L memory socket for a maximum total memory of 4GB in DDR3L memory type. Installing and Removing Memory Modules To install the DDR3L modules, locate the memory slot on the board and perform the following steps: 1. -
Page 12: Setting The Jumpers
INSTALLATIONS Setting the Jumpers Jumpers are used on IB898 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on IB898 and their respective functions. Jumper Locations on IB898 .............. -
Page 13: Jumper Locations On Ib898
INSTALLATIONS Jumper Locations on IB898 IB898 User’s Manual... -
Page 14: Jp1: Lvds Panel Power Selection
INSTALLATIONS JP1: LVDS Panel Power Selection Setting Panel Voltage Pin 1-2 3.3V (default) Short/Closed Pin 2-3 Short/Closed JP2: LVDS Panel Brightness Control Selection Brightness Control (PWM mode) 3.3V Open Close 5V(Default) IB898 User’s Manual... -
Page 15: Jp4: Clear Cmos Contents
INSTALLATIONS JP4: Clear CMOS Contents Setting Function Pin 1-2 Normal Short/Closed Pin 2-3 Clear CMOS Short/Closed JP5: Clear ME Contents Setting Function Pin 1-2 Normal Short/Closed Pin 2-3 Clear ME Short/Closed Register IB898 User’s Manual... -
Page 16: Connectors On Ib898
INSTALLATIONS Connectors on IB898 Connector Locations on IB898 ............12 CN1: USB3.0 Connector ..............13 CN3: Gigabit LAN Connector ............. 13 CN3: Intel® I210IT Connector............13 CN4: USB2.0 Connector ..............13 CN5: DP Connector ................13 CN6: CRT Connector ................13 CN7: DB9 Connector (COM1) ............ -
Page 17: Connector Locations On Ib898
INSTALLATIONS Connector Locations on IB898 IB898 User’s Manual... -
Page 18: Cn1: Usb3.0 Connector
INSTALLATIONS CN1: USB3.0 Connector CN3: Gigabit LAN Connector CN3: Intel® I210IT Connector CN4: USB2.0 Connector CN5: DP Connector CN6: CRT Connector CN7: DB9 Connector (COM1) Signal Name Pin # Pin # Signal Name DCD, Data carrier detect DSR, Data set ready RXD, Receive data RTS, Request to send TXD, Transmit data... -
Page 19: J1: Audio Connector
INSTALLATIONS J1: Audio Connector (DF11-12DP-2DSA) Signal Name Pin # Pin # Signal Name LINEOUT_R LINEOUT_L Ground JD_FRONT LINEIN_R LINEIN_L Ground JD_LINEIN MIC-R MIC_L Ground JD_MIC1 J2: MCU Flash Connector (factory use only) J3: Amplifier Connector (JST B4B-PH-K-S) Pin # Signal Name OUTL+ OUTL- OUTR-... -
Page 20: J4: Ddr3L So-Dimm Sockets
INSTALLATIONS J4: DDR3L SO-DIMM Sockets J5, J6: LVDS Connectors (DF20G-20DP-1V) J5: First Channel LVDS J6: Second Channel LVDS Signal Name Pin # Pin # Signal Name TX0N TX0P Ground Ground TX1N TX1P Ground Ground TX2N TX2P Ground Ground CLKN CLKP Ground Ground TX3N... -
Page 21: J7: Lcd Backlight Connector
INSTALLATIONS J7: LCD Backlight Connector (JST B4B-PH-K-S ) Pin # Signal Name +12V(1A) Backlight Enable Brightness Control Ground J8: SPI Flash Connector (factory use only) J9: SATAII /share mSATA/ Connectors IB898 User’s Manual... -
Page 22: J12: Sataii Connectors
INSTALLATIONS J12: SATAII Connectors J10, J11: SATA HDD Power Connectors (JST B4B-XH-A) Pin # Signal Name +5V(1A) Ground Ground +12V(1A) ** It is recommend to connect with 2.5” storage device only from J10/J11** J13: Mini PCIE Connector (Full Size) IB898 User’s Manual... -
Page 23: J14: Mini Pcie Connector (Share Msata)
INSTALLATIONS J14: Mini PCIE Connector (share mSATA) J15: Mini PCIE Connector (Half Size) J16: Front Panel Function Connector (2.54mm) Signal Name Pin # Pin # Signal Name Power BTN Power BTN HDD LED+ HDD LED- Reset BTN Reset BTN Power LED+ Power LED- IB898 User’s Manual... -
Page 24: J17: Board Input Power Connector
INSTALLATIONS J17: Board Input Power Connector (HK_WAFER396-2S-WV) Pin # Signal Name VCC12 J18: COM2/RS232 Serial Port (DF11-10DP-2DSA) Signal Name Pin # Pin # Signal Name DCD, Data carrier detect RXD, Receive data TXD, Transmit data Data terminal ready GND, ground DSR, Data set ready RTS, Request to send CTS, Clear to send... -
Page 25: J19: Digital I/O Connector
INSTALLATIONS J19: Digital I/O Connector (2.54mm) Signal Name Pin # Pin # Signal Name VCC(500mA) OUT3 OUT1 OUT2 OUT0 J21: Debug 80 Port Connector (factory use only) J22: USB 2.0 Connector (DF11-8DP-2DSA) Signal Name Pin # Pin # Signal Name Ground Ground IB898 User’s Manual... -
Page 26: Bios Setup
BIOS SETUP BIOS Setup This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows: BIOS Introduction ................22 BIOS Setup ..................22 Main Settings ..................23 Advanced Settings ................ -
Page 27: Bios Introduction
BIOS SETUP BIOS Introduction The BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel processors. The BIOS provides critical low-level support for a standard device such as disk drives, serial ports and parallel ports. It also password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system. -
Page 28: Main Settings
BIOS SETUP Main Settings Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Choose the system default language System Date [Tue 04/20/2015] → ← Select Screen System Time [13:52:06] ↑↓ Select Item Enter: Select Change Field F1: General Help... -
Page 29: Advanced Settings
BIOS SETUP Advanced Settings This section allows you to configure and improve your system and allows you to set up some system features according to your preference. Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Advanced Main Chipset Boot Security Save &... - Page 30 BIOS SETUP LVDS Configuration Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Advanced Main Chipset Boot Security Save & Exit LVDS Configuration → ← Select Screen LVDS Control Enabled ↑↓ Select Item Panel Color Depth 24 BIT Enter: Select LVDS Channel Type Single Change Opt.
- Page 31 BIOS SETUP Super IO Configuration Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Advanced Main Chipset Boot Security Save & Exit Super IO Configuration → ← EuP/ErP standby power control Keep standby power Select Screen ► Serial Port 1 Configuration ↑↓...
- Page 32 BIOS SETUP H/W Monitor Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Advanced Main Chipset Boot Security Save & Exit PC Health Status → ← Select Screen SYS temp +33.0 C ↑↓ Select Item CPU temp +40.5 C Enter: Select Vcore +0.776 V...
- Page 33 BIOS SETUP CPU Configuration This section shows the CPU configuration parameters. Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Advanced Main Chipset Boot Security Save & Exit CPU Configuration ►Socket 0 CPU Information → ← Select Screen CPU Speed 1334 MHz ↑↓...
- Page 34 BIOS SETUP IDE Configuration SATA Devices Configuration. Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Advanced Main Chipset Boot Security Save & Exit IDE Configuration Serial-ATA (SATA) Enabled SATA Speed Support Gen2 SATA Mode AHCI Mode Serial-ATA Port 0 Enabled SATA Port0 HotPlug Disabled...
- Page 35 BIOS SETUP USB Configuration Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Advanced Main Chipset Boot Security Save & Exit USB Configuration USB Module Version 8.11.03 USB Devices: 1Keyboard, 2 Hubs → ← Select Screen Legacy USB Support Enabled XHCI Hand-off Enabled...
-
Page 36: Chipset Settings
BIOS SETUP Chipset Settings Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Chipset Main Advanced Boot Security Save & Exit ► North Bridge → ← Select Screen ↑↓ Select Item Enter: Select Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save &... -
Page 37: Security Settings
BIOS SETUP Security Settings This section allows you to configure and improve your system and allows you to set up some system features according to your preference. Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Security Main Advanced Chipset Boot Save &... -
Page 38: Boot Settings
BIOS SETUP Boot Settings This section allows you to configure the boot settings. Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Boot Main Advanced Chipset Security Save & Exit Boot Configuration Setup Prompt Timeout Bootup NumLock State Quiet Boot Disabled Fast Boot Disabled... -
Page 39: Save & Exit Settings
BIOS SETUP Save & Exit Settings Aptio Setup Utility – Copyright © 2013 American Megatrends, Inc. Save & Exit Main Advanced Chipset Boot Security Save Changes and Exit Discard Changes and Exit Save Changes and Reset Discard Changes and Reset →... -
Page 40: Drivers Installation
DRIVERS INSTALLATION Drivers Installation This section describes the installation procedures for software and drivers. The software and drivers are included with the motherboard. If you find the items missing, please contact the vendor where you made the purchase. The contents of this section include the following: Intel Chipset Software Installation Utility ........... -
Page 41: Intel Chipset Software Installation Utility
DRIVERS INSTALLATION Intel Chipset Software Installation Utility The Intel Chipset Drivers should be installed first before the software drivers to enable Plug & Play INF support for Intel chipset components. Follow the instructions below to complete the installation. 1. Insert the DVD that comes with the board. Click Intel and then Intel(R) Baytrail Chipset Drivers. -
Page 42: Intel Baytrail Graphics Driver Installation
DRIVERS INSTALLATION Intel Baytrail Graphics Driver Installation 1. Insert the DVD that comes with the board. Click Intel and then Intel(R) Baytrail Chipset Drivers. Click Intel(R) Baytrail Graphics Driver. 2. When the Welcome screen appears, click Next to continue. 3. Click Yes to accept the license agreement and continue the installation. Click Next to continue. -
Page 43: Realtek High Definition Audio Driver Installation
DRIVERS INSTALLATION Realtek High Definition Audio Driver Installation Insert the DVD that comes with the board. Click Intel and then Intel(R) Baytrail Chipset Drivers. Click Realtek High Definition Audio Driver. 2. On the Welcome screen, click Next to proceed with the installation. 3. -
Page 44: Lan Drivers Installation
DRIVERS INSTALLATION LAN Drivers Installation 1. Insert the DVD that comes with the board. Click LAN Card and then click Intel LAN Controller Drivers. Click Intel(R) I21x Gigabit Network Drivers. 2. When the Welcome screen appears, click Next to continue. 3. -
Page 45: Intel Trusted Execution Engine Installation
DRIVERS INSTALLATION Intel Trusted Execution Engine Installation Note :Windows 7 OS only 1. Insert the DVD that comes with the board. Click Intel and then Intel(R) Baytrail Chipset Drivers. Click Intel(R) TXE Drivers. 2. On the Setup Welcome screen, click Next to proceed with the installation process. -
Page 46: Intel® Usb 3.0 Drivers
DRIVERS INSTALLATION Intel® USB 3.0 Drivers 1. Insert the DVD that comes with the board. Click Intel and then Intel(R) Baytrail Chipset Drivers. Click Intel(R) USB 3.0 Drivers. 2. When the Welcome screen to the InstallShield Wizard for Intel® USB 3.0 eXtensible Host Controller Driver, click Next. -
Page 47: Appendix
APPENDIX Appendix A. I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses which also becomes the identity of the device. The following table lists the I/O port addresses used. Address Device Description 0000h-006Fh PCI bus 0020h-0021h... - Page 48 APPENDIX Address Device Description D000h-DFFFh Intel(R) Pentium(R) processor N- and J-series / Intel(R) Celeron(R) processor N- and J-series PCI Express - Root Port 1 - 0F48 E000h-E01Fh Intel(R) Pentium(R) processor N- and J-series / Intel(R) Celeron(R) processor N- and J-series Platform Control Unit - SMBus Port - 0F12 E020h-E03Fh Intel(R) Pentium(R) processor N- and J-series /...
-
Page 49: Interrupt Request Lines (Irq)
APPENDIX B. Interrupt Request Lines (IRQ) Peripheral devices use interrupt request lines to notify CPU for the service required. The following table shows the IRQ used by the devices on board. Level Function IRQ 0 System timer IRQ 3 Nuvoton Communications Port (COM2) IRQ 4 Nuvoton Communications Port (COM1) IRQ 8... -
Page 50: Digital I/O Sample Code
APPENDIX C. Digital I/O Sample Code File of the NCT5523D.H //--------------------------------------------------------------------------- // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE. - Page 51 APPENDIX File of the MAIN.CPP //--------------------------------------------------------------------------- // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE.
- Page 52 APPENDIX void Dio5Initial(void) unsigned char ucBuf; ucBuf = Get_NCT5523D_Reg(0x1C); ucBuf &= ~0x02; Set_NCT5523D_Reg(0x1C, ucBuf); Set_NCT5523D_LD(0x07); //switch to logic device 7 //enable the GP2 group ucBuf = Get_NCT5523D_Reg(0x30); ucBuf |= 0x04; Set_NCT5523D_Reg(0x30, ucBuf); //--------------------------------------------------------------------------- void Dio5SetOutput(unsigned char NewData) Set_NCT5523D_LD(0x07); //switch to logic device 7 Set_NCT5523D_Reg(0xE1, NewData);...
- Page 53 APPENDIX File of the NCT5523D.CPP //--------------------------------------------------------------------------- // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE.
- Page 54 APPENDIX void Set_NCT5523D_LD( unsigned char LD) Unlock_NCT5523D(); outportb(NCT5523D_INDEX_PORT, NCT5523D_REG_LD); outportb(NCT5523D_DATA_PORT, LD); Lock_NCT5523D(); //--------------------------------------------------------------------------- void Set_NCT5523D_Reg( unsigned char REG, unsigned char DATA) Unlock_NCT5523D(); outportb(NCT5523D_INDEX_PORT, REG); outportb(NCT5523D_DATA_PORT, DATA); Lock_NCT5523D(); //--------------------------------------------------------------------------- unsigned char Get_NCT5523D_Reg(unsigned char REG) unsigned char Result; Unlock_NCT5523D(); outportb(NCT5523D_INDEX_PORT, REG); Result = inportb(NCT5523D_DATA_PORT); Lock_NCT5523D();...
-
Page 55: Watchdog Timer Configuration
APPENDIX D. Watchdog Timer Configuration The WDT is used to generate a variety of output signals after a user programmable count. The WDT is suitable for use in the prevention of system lock-up, such as when software becomes trapped in a deadlock. Under these sorts of circumstances, the timer will count to zero and the selected outputs will be driven. - Page 56 APPENDIX File of the MAIN.CPP. //--------------------------------------------------------------------------- // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE.
- Page 57 APPENDIX void WDTEnable(unsigned char NewInterval) unsigned char bBuf; Set_NCT5523D_LD(0x08); //switch to logic device 8 Set_NCT5523D_Reg(0x30, 0x01); //enable timer bBuf = Get_NCT5523D_Reg(0xF0); bBuf &= (~0x08); Set_NCT5523D_Reg(0xF0, bBuf); //count mode is second Set_NCT5523D_Reg(0xF1, NewInterval); //set timer //--------------------------------------------------------------------------- void WDTDisable(void) Set_NCT5523D_LD(0x08); //switch to logic device 8 Set_NCT5523D_Reg(0xF1, 0x00);...
- Page 58 APPENDIX File of the NCT5523D.CPP //--------------------------------------------------------------------------- // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE.
- Page 59 APPENDIX void Set_NCT5523D_LD( unsigned char LD) Unlock_NCT5523D(); outportb(NCT5523D_INDEX_PORT, NCT5523D_REG_LD); outportb(NCT5523D_DATA_PORT, LD); Lock_NCT5523D(); //--------------------------------------------------------------------------- void Set_NCT5523D_Reg( unsigned char REG, unsigned char DATA) Unlock_NCT5523D(); outportb(NCT5523D_INDEX_PORT, REG); outportb(NCT5523D_DATA_PORT, DATA); Lock_NCT5523D(); //--------------------------------------------------------------------------- unsigned char Get_NCT5523D_Reg(unsigned char REG) unsigned char Result; Unlock_NCT5523D(); outportb(NCT5523D_INDEX_PORT, REG); Result = inportb(NCT5523D_DATA_PORT); Lock_NCT5523D();...
- Page 60 Our company network supports you worldwide with offices in Germany, Austria, Switzerland, Great Britain and the USA. For more information please contact: Headquarters Germany FORTEC Elektronik AG Lechwiesenstr. 9 86899 Landsberg am Lech Phone: +49 8191 91172-0 E-Mail: sales@fortecag.de Internet: www.fortecag.de Fortec Group Members Austria...