Advertisement
Key:
1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Breather Lid
2 . . . . . . . . . . . . . . . . . . . . . . . . . . . Pump On/Off Switch
3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Battery Clips
4 . . . . . . . . . . . . . . . . . . . . . . . . . Automatic Fluid Nozzle
5 . . . . . . . . . . . . . . . . . . . . . . . .Securing Strap Locations
6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vent Plug
7 . . . . . . . . . . . . . . . . . . . . . . . . . . . Moulded Hand Holds
4. OPERATION
4.1.
FILLING AND TRANSPORT
4.1.1. Move the empty tank assembly with two persons using
the hand holds moulded into the unit (fig.1.7).
DO NOT run the pump without fuel in the tank. To do
8
so will damage the pump's internal components and
will invalidate your warranty.
4.1.2. The tank is filled by unscrewing the filler cap (fig.1.1)
in an anticlockwise direction. Refit the filler cap
immediately after filling.
WARNING take care not to overfill the tank.
‰
4.1.3. Ensure that the filler cap is closed before moving.
4.1.4. Secure the tank to the carrying vehicle by ratchet
straps. Locations for the straps are moulded into
the tank (fig.1.5).
4.2.
FUEL DISPENSING
4.2.1. Before connecting to a battery, make sure that the pump switch (fig.2.2)
is in the 'off' (O) position.
4.2.2. Connect the battery clips (fig.1.3) to the 12V battery, observing correct
polarity (red clamp to +ve terminal, black clamp to -ve terminal)
4.2.3. Switch the pump switch (fig.2.2) to the 'on' (I) position.
4.2.4. Unwind sufficient hose and place the nozzle (fig.1.4) in the receiving
tank and pull the trigger (fig.3).
4.2.5. The trigger can be locked in one of three positions by engaging the
latch (fig.3) to hold the trigger open.
DO NOT leave the nozzle unattended with the trigger latched open.
8
4.2.6. Slight pressure on the trigger will release the latch.
4.2.7. When the level in the receiving tank reaches the nozzle, delivery will
stop automatically.
4.2.8. When delivery is complete, switch off the pump.
DO NOT operate the pump continuously for more than 30 minutes.
8
The duty cycle of the unit is 30 minutes, after which the motor must
be left to cool down for a further 30 minutes.
DO NOT run the unit for more than 2-3 minutes with the delivery nozzle
8
closed.
5. MAINTENANCE
5.1.
The pump contains no user-servicable parts. Repairs should only be undertaken by competent persons.
5.2.
Check the integrity of all the hose connections periodically. If any leakage is evident, strip the joint and
wind PTFE tape around the male thread.
5.3.
Check all electrical connections and cables for wear and damage. Rectify any faults found.
5.4.
Keep clean, especially the dispenser nozzle. Clean with a damp, soapy cloth.
DO NOT use abrasive or solvent cleaners.
8
Parts support is available for this product. Please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
fig.1
01284 703534
sales@sealey.co.uk
Original Language Version
1
7
5
6
3
4
fig.2
2
2
5
7
fig.3
www.sealey.co.uk
D100T | Issue 1 26/11/18
Advertisement
