Advertisement

Available languages

Available languages

TRANSMITTER
产品介绍 Introduction
KT-19 遥控系统主要是用来遥控摩托车模型,通过对发射机进行操作,可以分别
实现相对应的马达驱动及舵机摆动遥控控制;发射机采用 6V/DC 供电,摩托车采用
3.7V 锂聚合物电池进行供电。
KT-19 radio system mainly uses for remote control the motorcycle model.
Through operating transmitter, it can succeed in moving the motor system and the
servo respectively. The transmitter will be supplied by 6V/DC, while the receiver will
be supplied by 3.7V li-poly battery.
产品套装:发射机+摩托车(接收机)+USB 线+充电器+使用说明书。
Product includes: transmitter + motor (receiver)+USB cable + charger + manual
KT-19 遥控系统使用方法及操作步骤

Instruction of KT-19

1. 将发射机与摩托车(接收机)靠近;
1. Keep the transmitter and model closer.
2. 将发射机手轮顺时针拧到底,然后按下电源开关"POWER",此时发射机 LED 指示
灯会处于闪烁状态;
2. Turning the steering wheel to the end clockwise, and at the same time press the
POWER, then the LED will be flashing.
3. 打开接收机电源开关,接收机 LED 指示灯会长亮 2 秒时间,然后处于闪烁状态,
同时,无刷电机也会发出"滴、滴、滴"的响声;
3. Switch on the power of receiver, then the LED of receiver will be lighting for 2
seconds, after that it will be flashing, and at the same time the brushless motor will
be beeping.
KT-19
 

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KT-19 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Kyosho KT-19

  • Page 1 实现相对应的马达驱动及舵机摆动遥控控制;发射机采用 6V/DC 供电,摩托车采用 3.7V 锂聚合物电池进行供电。 KT-19 radio system mainly uses for remote control the motorcycle model. Through operating transmitter, it can succeed in moving the motor system and the servo respectively. The transmitter will be supplied by 6V/DC, while the receiver will be supplied by 3.7V li-poly battery.
  • Page 2 发射机相关技术参数: The parameter of transmitter 1. KT-19 发射机工作在 2405.5MHz-2475 MHz 频段内; 1. The frequency of KY-GT2 is between 2405.5MHz to 2475MHz 2. 静态工作电流 17mA 左右; 2. The quiescent current is about 17mA 3.
  • Page 3   The parameter of motor 摩托车机身长、宽、高:116 x 70 x 70mm; The size of motor is 116*70*70mm 发射机外观功能指示图: The name of different part on the transmitter 9  1  12  11  10  2  7  3  8  4  5  6  1. 天线 2.LED 灯透明盖 3.USB 线接口...
  • Page 4   9. Trim of steering 10. Trim of gyro (low speed ) 11. Trim of gyro (high speed) 12. Power on/off 供电电池说明 The instruction of battery 发射机采用 4 节干电池供电,电池型号为 AAA/1.5V;接收机采用 3.7VLi 电池供电。 The transmitter will be supplied by 4 cells dry battery; the model of battery is AAA/1.5V.
  • Page 5 When the LED is green, it means the battery is full or the battery fail to connect. 注意事项 Notes 此款遥控模型运用了多款高科技技术,设计制造有一定的复杂性,使用之前请详细 阅读《KT-19 使用说明书》 ,掌握相应的操作技术及安全规则。 The radio uses several high technologies, and the design and production are complex, so please read the manual carefully and master the operation and safety rules before using.
  • Page 6   5. The transmitter and receiver are component by many precise electronic parts. Please keep them from the humidity to avoid causing any kind of circuit problems. 警告 Warming 保养方法:需防震、防火、防潮。 Method of maintenance: Keep them from shaking, fire and humidity.  ...

Table of Contents