Page 2
• Because this terminal conducts wireless B efore Using this communication by transforming sound into Terminal digital signal, the received sound may diff er from the actual one if the transmitted digital • This terminal supports LTE, GSM/GPRS and signal cannot properly be restored according wireless LAN systems. to conditions such as moving into a poor • Since this terminal uses wireless signal, signal area. it may not be able to use in a location • Regularly take a memo of the information you with no signal reception such as a tunnel, registered in this terminal or store it in the underground, a building, an outdoor location external memories such as microSD card or with weak or poor signal reception, or a PC. XXX assumes no responsibility for any location outside of the XXX service areas. loss of your data caused by malfunction, Also this terminal may not be able to use repair, change to a new model or any other on high upper fl oors of high-rise apartments reasons. or buildings, even if you can see no • Even though the display on this terminal obstructions around you. Please note that on applies advanced technique, part of the dots occasion, data communication may become may not light up as well as those always-on ...
Page 3
• The same as a PC, when you install an • This terminal does not support Pubic mode application, this terminal's performance may (driving mode). become unstable, or your location information • In this terminal, sounds other than ringtone and personal information registered on this and notifi cation sounds (video playback terminal might be sent to outside via Internet sound, music playback sound, shutter sound, and therefore cause fraudulent use. To avoid etc.) cannot be muted even when it is set to this, make sure to confi rm the source and the "Manner Mode (Vibrate only, Do not disturb)". operating conditions of the application before • You can confi rm your own phone number as installation. follows. • This terminal uses only nano UIM card. Bring From the Home screen, "Apps" X "Settings" X your mini UIM card, UIM card or XXX card to a "About phone" X "Status". Shop to exchange it. • You can confi rm the software version of this • This terminal does not respond to i-mode terminal as follows. website (programs) access or i- α ppli, etc. From the Home screen, "Apps" X "Settings" X ...
Page 4
• Please read the terms of service of Google Safety Precautions (ALWAYS Inc. regarding Google services. Also, read FOLLOW THESE PRECAUTIONS) each terms of services for other web services. ■ Before using this terminal, read these • In case of loss of the terminal, set the screen "Safety Precautions" carefully so that you to ensure the security of the terminal. For can use it properly. After reading the safety details, refer to "Lock Screen" (P175). precautions, keep this manual in a safe place • If you lose your terminal, change password for later reference. of online service accounts from PC so that Google Services such as Gmail, Google Play, ■ These precautions are intended to protect and service such as SNS, etc. should not be you and others around you. Read and follow used by others. them carefully to avoid injury, damage to the • This terminal does not support service product or damage to property. providers other than sp-mode, mopera U or ■ The signs below indicate the levels of danger Business mopera Internet. or damage that may occur if the particular • Subscription to sp-mode is required when precautions are not observed.
■ The following symbols indicate special ■ "Safety Precautions" are explained in the warnings regarding product usage. following seven sections. Handling the Terminal, Battery Pack, Adapter, TV Antenna Cable, Mickey Window Cover and Denotes things not to do nano UIM card (Common) ………………… P10 (prohibition). Precautions for this Terminal …………… P13 Precautions for Battery Pack …………… P17 Precautions for Adapter … ………………… P19 Denotes not to disassemble. Precautions for Mickey Window Cover …………………………………………………… P22 Precautions for nano UIM card Denotes not to use where it …………………………………………………… P22 could get wet. Precautions for Using near Electronic Medical Equipment ………………………… P22 Denotes not to use with wet ...
Do not get wet with water, drinking H andling the Terminal, Battery Pack, water, pet urine, sweat, etc. Adapter, TV Antenna Cable, Mickey Window Fire, burns, injury, or electric shock may result. Cover and nano UIM card (Common) For waterproofness, refer to the following. → P34 "Waterproofness/ DANGER Dustproofness" Do not get wet on charging connector, Do not use, store or leave it in places microUSB connection terminal or with a high temperature such as earphone/microphone jack by liquids besides fi re, besides a heater, inside such as water, drinking water, pet a kotatsu, under direct sunlight or in urines, sweat, etc. cars under the blazing sun. Fire, burns, injury, or electric shock Fire, burns, or injury may result. may result. For waterproofness, refer to the Do not put in heating appliances following. → P34 "Waterproofness/ such as microwaves or high pressure Dustproofness" containers. Fire, burns, injury, or electric shock Use the optional accessories specifi ed may result. by XXX for this terminal. Fire, burns, injury, or electric shock Do not disassemble or remodel. may result.
Page 7
Make sure to turn off this terminal WARNING or stop charging before going to the places like a gas station where a fl ammable gas fumes. Do not put strong force, severe shocks, or throw them. Catching fi re may result. Fire, burns, injury, or electric shock Turn off the power when using Osaifu- may result. Keitai at gas stations (before turning off the power, release the lock for Osaifu-Keitai if it is set). Do not let charging connector, microUSB connection terminal or earphone/microphone jack touch any If the equipment starts giving off a conductive metal such as metal piece, strange smell, overheats, becomes pencil lead, etc. Also do not put any of discolored or deformed during use, them inside. charging or in storage, immediately Fire, burns, injury, or electric shock perform the following operations. may result. • Remove the power plug from the wall outlet or cigar lighter socket. • Turn off this terminal. Do not cover or wrap this terminal • ...
Page 8
Be careful especially when using this CAUTION terminal with the adapter connected continuously for a long time. If you use video call, watch videos, Do not place the horizontal charge play games, watch TV, etc. while adapter on unstable locations such as wobbly tables or slanted locations. charging the battery for a long time, Injury may result from the terminal the terminal, battery pack and adapter falling down. may be heated. Directly touching a hot part for a long time may cause redness, itching or Do not store the horizontal charge rash on your skin, or low-temperature adapter in humid, dusty places, or in burns depending on your constitution hot areas. and/or health condition. Fire, burns, or electric shock may result. If children use it, a guardian should explain the precautions and correct operations. Also make sure that the instructions are followed during use. Injury may result. Keep out of reach of babies and small children. Accidental swallowing, injuries or electric shock may result. Contents/Precautions...
P recautions for this Terminal WARNING Do not lighten the light near eyes. Especially, when you shoot photos of babies or infants, keep this terminal 1 m or more away from babies and infants. Vision problems may result. Accidents may result from being blind or being shocked. Do not get liquids such as water, or foreign objects such as metal pieces or fl ammable materials into the nano UIM card slot or microSD card slot of this terminal. Fire, burns, injury, or electric shock may result. Do not turn on lights in front of the auto driver directly. Accident may result from the weak vision caused by light. Contents/Precautions...
Page 10
When boarding an airplane, turn the When you talk via handsfree setting terminal OFF or turn airplane mode on. or when the ringtone is ringing, keep As there are usage restrictions in an the terminal away from your ear. airplane, follow the instructions from And, when connecting the earphone/ the airline. microphone jack etc. to this terminal Failure to do so may cause airplane and playing a game or music, adjust electronic equipment to fail or the volume moderately. malfunction. Too loud volume may cause a hearing If you commit any prohibited acts, loss. And, if you cannot hear the sound such as using the phone in an airplane, around you clearly, it may cause an you will be punished in accordance accident. with the law. If you have a weak heart, be careful When using the terminal in a medical when setting the Vibrate alert facility, follow the instructions of the (vibration) or alert volume setting. facility. Harmful eff ect on heart may result. Turn the terminal OFF in areas where use is prohibited. When you use electronic medical Electronic devices or electronic equipment, check with the equipment medical devices may be adversely manufacturer to determine how the aff ected. device is aff...
Page 11
Turn off this terminal in places near When the display or camera lens is high precision electronic devices or accidentally broken, be careful of devices using weak electronic signals. broken glass or exposed internal Electronic devices may be adversely parts of this terminal. aff ected by reasons such as malfunction. Since the reinforced glass is used * Examples to pay attention to when on the surface of the display and the using electronic devices camera lens, they are structured for Hearing aids, implanted cardiac the glass not to scatter. However, pacemakers, implanted defi brillator, if you carelessly touch broken or other medical electronic devices, fi re exposed parts, you may get injured. alarms, automatic doors and other automatically controlled devices. If you are using an implanted cardiac pacemaker, implanted defi brillator or any other electronic medical device, consult the manufacturer or retailer of the device for advice regarding possible eff ects from radio waves. Contents/Precautions...
Page 12
If the display part is accidentally CAUTION broken and liquid crystal leaks out, do not make the material contact with your skin of face or hands. Do not swing this terminal by its It leads to blindness or skin problems. strap, etc. It may hit you or someone else and If liquid crystal gets into your eyes or may result in an accident such as an mouth, rinse it with clean water and injury. see a doctor immediately. And, if the material adheres to skin or clothing, use alcohol etc. to immediately wipe it Do not use a broken terminal. off , and then wash with soap. Fire, burns, injury, or electric shock may result. If you use this terminal in a car, contact the car manufacturer or When using the motion sensor, ensure dealer to ask about the eff ect from the safety of you and those around radio waves. you, hold this terminal fi rmly, and Depending on the type of car, in-car avoid extreme movements. electronic devices could be adversely Injury may result. aff ected. In this case, stop using this terminal immediately. Contents/Precautions...
Itching, rash or eczema may be P recautions for Battery Pack caused depending on your physical conditions or predisposition. If an ■ Confi rm the battery type from the label of abnormality occurs, stop using this the battery pack. terminal immediately, and then seek medical attention. Display Battery type • For the material of each part Li-ion00 Lithium-ion battery → P23 "Material List" When watching the display, take a DANGER certain distance from the display in a fully bright place. Do not contact the connector with Visual loss may result. metal such as wire. Also do not carry or store it with metal necklace, etc. Fire, explosion, getting heated or liquid leak of the battery pack may result. Check the orientation of the battery pack when inserting it into this terminal. Stop putting excessive force when any problem is found during inserting. Fire, explosion, getting heated or liquid leak of the battery pack may result. Contents/Precautions...
Page 14
Do not throw this terminal into fi re or WARNING heat it. Fire, explosion, getting heated or liquid leak of the battery pack may result. Stop using it when transformation or damage is caused by dropping. Fire, explosion, getting heated or liquid Do not put excessive force such as leak of the battery pack may result. nailing the battery pack, hitting with a hammer or stepping on it. Fire, explosion, getting heated or liquid When battery pack leaks liquid or leak of the battery pack may result. gives off odor, stop using it and keep it away from fi re. Ignition, fi re, explosion may result from When the liquid from battery pack liquid leaking. splashes into your eyes, do not rub your eyes. Wash your eyes and go to consult with a doctor immediately. Keep pets away from biting the Blindness may result. battery pack. Fire, explosion, getting heated or liquid leak of the battery pack may result. Contents/Precautions...
P recautions for Adapter CAUTION Do not discard it as combustible WARNING waste. Fire and environmental pollution may Do not use it if the adapter cord gets result. Tape the connector to isolate damaged. the battery pack and bring it to a Shop Fire, burns, or electric shock may or follow the local disposal regulations. result. Do not use or charge the wet battery Do not use the AC adapter in a highly pack. humid area such as a bathroom. Fire, explosion, getting heated or liquid Fire, burns, or electric shock may leak of the battery pack may result. result. When battery pack leaks liquid inside, DC adapter is only for minus earth do not touch your skin, such as your car. Do not use it on plus earth car. face or hands. Fire, burns, or electric shock may It leads to blindness or skin problems. result. If such liquid gets into your eyes or mouth, if it adheres to your skin or clothing, please rinse with clean water When it starts to thunder, do not immediately. If it gets into your eyes or touch the adapter. mouth, please seek medical attention Electric shock may result. immediately after washing. Contents/Precautions...
Page 16
Do not make the charging terminal Do not touch the adapter cord, short out while being connected to charging connector or the outlet with the outlet or cigar lighter socket. Do wet hands. not touch the charging terminal with a Fire, burns, or electric shock may part of your body such as your hands result. or fi ngers. Fire, burns, or electric shock may Only use with the specifi ed power result. source and voltage. When charging overseas, use a compatible AC Do not place heavy objects on the adapter. adapter cord. If incorrect voltage is used, this may Fire, burns, or electric shock may cause fi re, burns or electric shock. result. • AC adapter: AC 100 V • DC adapter: DC 12 V/24 V (only for minus earth car) When you insert and remove AC • Available AC adapter used overseas: adapter from the power outlet, do not AC 100 V to 240 V (connect to contact a metal strap or any other household AC outlet only) metal objects with this terminal. Fire, burns, or electric shock may Use the specifi...
Page 17
Wipe off any dust that accumulated Always remove the power plug from on the power plug. the outlet or cigar lighter socket when Fire, burns, or electric shock may not using the adapter for an extended result. period. Fire, burns, or electric shock may result. When you connect the AC adapter to an outlet, do not fail to properly Immediately remove the power plug connect to the outlet. from the outlet or cigar lighter socket Fire, burns, or electric shock may if water or other fl uids get into the result. adapter. Fire, burns, or electric shock may result. When you disconnect the power plug from the outlet or cigar lighter socket, Always remove the power plug from do not pull the adapter cord with the outlet or cigar lighter socket when excessive force. Instead, hold the cleaning the equipment. adapter to disconnect. Fire, burns, or electric shock may result. Fire, burns, or electric shock may result. CAUTION When inserting and removing from this terminal, do not subject excessive Do not touch the adapter for a long force. Insert and remove horizontally. time while being connected to the Fire, burns, injury, or electric shock outlet or a cigar lighter socket. may result.
P recautions for Mickey P recautions for Using near Window Cover Electronic Medical Equipment CAUTION WARNING If you use electronic medical Do not pinch your fi ngers when equipment such as an implanted attaching the mickey window cover. cardiac pacemaker or implanted Accidents like injuries may result. defi brillator, use this terminal 15 cm or more away from the implanted cardiac pacemaker or implanted defi brillator. P recautions for nano UIM Operations of electronic medical card equipment may be adversely aff ected by radio waves. CAUTION Patients using electronic medical equipment other than implanted cardiac pacemakers or implanted Be careful of the cut surface when defi brillator (using outside medical handling nano UIM card. facilities for treatment at home, Injury may result. etc.) should check the infl...
You may get closer than 15 cm to M aterial List people around you who are incapable of moving. Set this terminal to radio Surface signal off beforehand (Airplane mode Part Material Treatment or power off ). People who are using electronic Display Tempered AF coating medical equipment such as implanted Glass cardiac pacemakers or implanted Outer case (front) UV coating defi brillators may be around you. Operations of electronic medical Outer case (back) equipment may be adversely aff ected Power key/Volume After injection by radio waves. spray (UV) Earphone/microphone Copper alloy Nickel + Follow the instructions when using jack, micro USB Gold plating this terminal inside medical facilities.
Page 20
Surface Surface Part Material Part Material Treatment Treatment Receiver grill Etching Back Body hole + Cover Terminal Copper + Pi Copper buffi ng + section sheet + Gold coating nano UIM card slot Copper alloy Nickel + Rubber Silicone (NKC286R- Pd-Ni + gasket Gold plating for water microSD card slot Stainless Nickel + proofi ng Gold plating Battery pack Ti-Cu Nickel + ...
Page 21
Surface Surface Part Material Part Material Treatment Treatment TV Earphone/ Copper Nickel Mickey Outer polyurethane Logo print Antenna microphone plating Window cover fi ber Cable jack (top) Cover Window SN Earphone/ TPE̲ Non PVC frame Deposition, microphone JS400-78A laser etching jack (outer Decoration Glass Glass cover) processing Cable...
Page 22
■ Clean this terminal with a dry, soft cloth Handling and Care (lens cleaning cloth), etc. • Rubbing it roughly with a dry cloth may scratch the display. General Usage Guidelines • Drops of water or dirt left on the display may cause stains. ■ Even though KS1604 provides with • If this terminal is wiped with alcohol, paint waterproofness/dustproofness function, do thinner, benzine or detergent, the printing not let water or dust come into contact with may disappear or color may fade. the interior of this terminal or adhere to the ■ Keep the connector contacts clean with a optional accessories. dry cotton swab. The battery pack, adapter, TV antenna Clean the connector contacts with a dry cable and nano UIM card do not have cotton swab to prevent contacts from waterproofness/dustproofness function. getting dirty which can result in intermittent Do not use them in places with high humidity connections. such as a bath or where rain may get it wet. Be careful when cleaning the connector If you carry this terminal close to your body, contacts. moisture from sweat may corrode the internal ...
Page 23
■ Do not place excessive force on this Notes about this Terminal terminal, battery pack, etc. If this terminal is inserted to a full bag, or ■ Do not press display surface forcibly, or not placed in a pocket and sat on, the display, operate with a sharp-pointed objects such its internal PCBs and battery pack may be as nail, ballpoint pen, pin, etc. damaged or malfunction. Doing so may cause damage of display. Also, if an external connection device is ■ Avoid using in extremely high or low connected to a microUSB connection temperatures. terminal or earphone/microphone jack, This terminal should be used within a damage or malfunction may result. temperature range from 5℃ to 35℃ and a ■ Do not rub or scratch the display with metal. humidity range from 45% to 85%. The display may get scratched and it may ■ This terminal may adversely aff ect fi xed cause malfunction or damage. phones, televisions or radios in use nearby. ■ Read the individual manual attached to the ...
Page 24
■ It is normal for this terminal to become warm Notes about Battery Pack during use or charging. You can continue using without problems. ■ Battery pack is a consumable supply. ■ Do not leave the camera under direct Battery life varies depending on usage sunlight. conditions, etc., but it is time to change Discoloring or burn-in of materials may result. battery pack when the usage time has become extremely short even though the ■ Do not use this terminal without its back battery pack has been fully charged. Please cover attached. purchase a specifi ed new batter pack. Falling off the battery pack, damage or malfunction may result. ■ Charge in an environment with the proper ambient temperature (5℃ to 35℃ ). ■ While using the microSD card, do not remove it from this terminal or turn this terminal off . ■ Battery life may diff er depending on the ...
Page 25
N otes about the Adapter Notes about Mickey Window Cover ■ Charge in an environment with the proper ambient temperature (5℃ to 35℃ ). ■ Do not get it wet. ■ Do not charge in the following places. Up to a certain level, the surface of mickey • Places that are very humid, dusty or window cover is waterproofed due to the exposed to strong vibrations. water repellent fi nish, however, it is not • Near ordinary phone or TV/radio. complete waterproof. Do not use them in places with high humidity such as a bath or ■ It is normal that the adapter becomes warm where rain may get it wet. If you carry this while being charged. You can continue using terminal close to your body, moisture from without problems. sweat may corrode the internal parts causing ■ Use the DC adapter only when the car a malfunction. engine is running. ■...
Page 26
■ Do not bend or put heavy things on the nano N otes about the nano UIM UIM card. card Malfunction may result. ■ Do not insert nano UIM card into this ■ Do not put excessive force on the nano UIM terminal with labels or stickers attached on. card when inserting into or removing from Malfunction may result. this terminal. ■ Note that XXX assumes no responsibility ® Notes about the Bluetooth for malfunctions occurring as the result of Function inserting and using a nano UIM card with other IC card reader/writer. ® ■ To secure the Bluetooth communication ■ Always keep the IC portion clean. security, this terminal supports the ■ Clean it with a dry, soft cloth (lens cleaning ...
Page 27
® ■ Frequency band ■ Bluetooth Device Cautions The frequency band that the devices with The operating frequency band of this terminal ® Bluetooth function and WLAN equipped is used by industrial, scientifi c, consumer uses is written on the insertion part of the and medical equipment including microwave batter pack on the main unit of this terminal. ovens, premises radio stations for identifying It shows how to read the label below. mobile units used in the manufacturing lines of plants (radio stations requiring no license) 2.4FH1/DS4/OF4 and amateur radio stations (hereinafter referred to as "another station"). : This radio equipment uses 1. Before using this terminal, confi rm that the 2400 MHz band. "another station" is not being operated FH/DS/OF : Indicates that modulation nearby. methods are FH-SS, DS-SS 2. In the event of this terminal causing or OFDM format. harmful radio wave interference with ...
Page 28
■ 2.4GHz Bandwidth Cautions Notes about Wireless LAN (WLAN) The operating frequency band of the WLAN device is used by home electrical appliances ■ Wireless LAN (WLAN) uses radio waves such as microwave ovens, industrial, scientifi c, to enable data communications between consumer and medical equipment including compatible devices, thus allowing connection premises radio stations for identifying mobile to a local area network from anywhere units used in the manufacturing lines of plants within range. However, there is a risk of data stations (radio stations requiring no license) interception by malicious third parties unless and amateur radio stations (radio stations security is established. Users are advised to requiring a license). assess their responsibilities and accordingly confi gure security settings. 1. Before using the device, confi rm that ■ Wireless LAN premises radio stations for identifying Do not use wireless LAN near magnetic mobile units, specifi ed low power radio devices such as electrical appliances, AV/ stations and amateur radio stations are OA devices, or in radio waves. not being operated nearby. • ...
Page 29
■ 5 GHz Bandwidth Cautions Caution The terminal can use 3 frequency bands of 5.2 GHz band (W52), 5.3 GHz band (W53), ■ Do not use a modifi ed terminal. Using a 5.6 GHz band (W56). modifi ed terminal results in violating Radio • W52 (5.2GHz bandwidth/36, 40, 44, 48 ch) law/Telecommunications Business Act. • W53 (5.3GHz bandwidth/52, 56, 60, 64 ch) This terminal has been complied with • W56 (5.6GHz bandwidth/100, 104, 108, 112, the rules related to technical standard of 116, 120, 124, 128, 132, 136, 140 ch) wireless equipment stipulated by Radio Using outdoors in 5.2/5.3 GHz (W52, W53) law, as well as technical standard of device outside is prohibited by the Radio Law. stipulated by Telecommunications Business Act. As a proof, "Technical standard Handling the FeliCa and NFC compliance mark " is depicted on the electronic nameplate of the terminal. You Reader/Writer can check the electronic nameplate in the terminal as follows. ■ The FeliCa and NFC reader/writer, P2P From the Home screen, "Settings" X"About function for this terminal handle delicate ...
Page 30
■ Be careful when using this terminal while W aterproofness/ driving. Dustproofness Using this terminal in your hand while driving is subject to punishment. KS1604 provides waterproofness of IPX7 * However, absolutely necessary cases such and dustproofness of IP6X * with fi rmly as rescue of a sick person or maintaining attaching the back cover. public safety are exempted. This terminal has the IPX7 waterproof function ■ Only use the FeliCa reader/writer function in and IP6X dustproof function even when the Japan. mickey window cover is attached. Even if The FeliCa reader/writer function for the surface of Mickey Window Cover L01 is this terminal is compliant with the radio processed with water repellent fi nish, when it standards for Japan. gets wet, dry it up completely before using. Overseas usage may be subject to *1 IPX7 means that a phone keeps punishment.
Page 31
What You can Do with B efore Using Waterproofness of K S1604 To maintain the waterproofness/ dustproofness, be sure to observe the • You can talk without an umbrella in the rain following points. (for rainfall of 20 mm or less per hour). • Make sure to fi rmly close the back cover/ • You can wash this terminal by soaking in a mickey window cover. Even a fi ne obstacle sink of fresh water or in tap water at room (one hair, one grain of sand, tiny fi ber, etc.) temperature (5℃ to 35℃ ) and gently shaking which is put between contact surfaces may allow water or dust to enter. - Attach the back cover/mickey window • Make sure that the back cover/mickey cover. window cover is closed fi rmly without any - Do not use any brush, sponge, soap, gap. detergent, etc to wash this terminal. • Do not pull strongly towards outside when ...
Page 32
A ttaching the back cover D etaching the back cover Confi rm the orientation of the back Put your fi nger in the groove which cover and align it with the main unit, is on the side of the back cover press 〇 parts fi rmly to attach the and hold it up in the direction of the back cover arrow to detach • Make sure that there are not any gaps between the cover and this terminal. Contents/Precautions...
Page 33
A ttaching mickey window cover D etaching mickey window cover Confi rm the back cover section Put your fi nger in the groove which orientation of the mickey window is on the side of the back cover cover and align it with the main unit, section of mickey window cover press 〇 parts to attach the mickey and hold it up in the direction of the window cover fi rmly arrow to detach • Make sure that there are not any gaps between the cover and this terminal. To maintain the waterproofness/ dustproofness, it is recommended to change the parts once in two years regardless of * Do not peel off the sticker on the back of malfunction. We will replace the parts by the back cover section. If the sticker is keeping this terminal, and this will be done peeled off , you cannot use Osaifu-Keitai. at user's expense. Bring your terminal to a repair counter specifi ed by XXX. Contents/Precautions...
Page 34
• Do not leave water on this terminal. The P recautions external connection terminal may short out. In cod area, this terminal freezes up and Do not pour or put in liquid etc. other than may cause malfunction. water at room temperature shown in the • To avoid dew condensation when you bring illustrations below. this terminal from a cold place to a warm <Example> place, wait until this terminal becomes room temperature. • Do not use this terminal in the water. • Never try to charge when this terminal is Soap/Detergent/ Seawater wet. Bath powder • Do not wash with washing machine etc. • This terminal does not fl oat on water. • Do not put directly on beach. - Sand etc. may get inside of earpiece (receiver), mouthpiece (microphone), Pool water Hot spring water Sand/Clay sub microphone, speaker or earphone/ microphone jack. etc., and the volume ...
Page 35
• Do not pick earpiece (receiver), mouthpiece • Do not insert a sharp object into a gap of (microphone), sub microphone, speaker, the back cover/mickey window cover. The earphone/microphone jack or microUSB rubber seal may get damaged, and water or connection terminal. The waterproofness/ dust exposure may result. dustproofness may not be eff ective. • When opening or closing the back cover/ • Do not leave water drop in the earpiece mickey window cover, do not apply (receiver), mouthpiece (microphone), excessive force on the rubber seal. sub microphone, speaker or earphone/ • Do not attach or detach the back cover/ microphone jack. Malfunction may result. mickey window cover when your hands are • Do not leave water drop in microUSB wet or when this terminal got wet. connection terminal or earphone/ • Replace the back cover/mickey window microphone jack. This terminal may short cover when either of them gets damaged. out. • When back cover/mickey window cover gets damaged, or when this terminal gets ■ Back cover/Mickey window cover wet while the cover is open, liquid might • ...
Page 36
Shake this terminal approximately D raining Water 20 times for each side, fi rmly When this terminal gets wet, make sure to holding it, until there is no more drain the water in the following steps. water splattering • Using this terminal with water drop, the • Visually confi rm if no water drops are on volume of speaker etc. becomes low and the this terminal. quality may change. Wipe off moisture on the surface with a dry cloth Contents/Precautions...
Page 37
Gently press this terminal to a dry Wipe off water drained from the and clean cloth to wipe off water terminal with a dry, clean cloth etc., remaining in the gap between and dry naturally earpiece (receiver), mouthpiece • Water, if any, remaining in the terminal (microphone), sub microphone, may ooze up after wiping off . speaker, earphone/microphone jack, C harging microUSB connection terminal, key, etc. The supplied accessories and optional • Do not wipe off the remaining moisture in accessories have no waterproofness/ the gaps directly with a cotton swab etc. dustproofness function. Check the following before and after charging. • Check if this terminal is not wet. Never try to charge when this terminal is wet. • Do not touch the AC adapter with wet hands. Electric shock may result. • Do not use the AC adapter in a place near water such as bathroom, shower room, kitchen, washroom etc. Fire or electric shock may result. Contents/Precautions...
Page 38
Confi rmation and Settings before Using Earpiece (receiver) P art Names and Functions Proximity sensor * /Illuminance sensor * (all-in-one) Front camera Notifi cation LED Light H all-IC sensor * D isplay (touch screen) Mouthpiece (microphone) Strap holder Confi rmation and Settings before Using...
Page 39
Earphone/microphone jack Sub microphone • When speaker phone is in use. Sub antenna area * Main camera Flash ® ® antenna area * Bluetooth /Wi-Fi GPS/sub antenna area * Volume key (up) Power key Volume key (down) Sub antenna area * mark Back cover * Speaker XXX antenna area * microUSB connection terminal • You can use a SlimPort supported cable purchased in stores. Confi rmation and Settings before Using...
Page 40
*1 Set touch screen to on or off to prevent nano UIM card unwanted operations from happening when your face touches the screen during Nano UIM card is an IC card that stores calling. information such as your telephone number. *2 Sense the surrounding brightness and • This terminal uses only nano UIM card. Bring adjust the screen brightness automatically. your mini UIM card, UIM card or XXX card to a *3 The sensor is used to recognize if the Shop to exchange it. mickey window cover is open or close. • If the nano UIM card is not inserted, the *4 Antennas are built in this terminal. If you functions such as phone call (sending and cover the antenna area with your hand, its receiving), mail (sending and receiving) and quality may be aff ected. the data communication cannot be used. *5 Do not peel off the sticker on the back of • In Japan, if the nano UIM card is not inserted, the back cover. If the sticker is peeled off , the emergency calls (110, 119, 118) cannot you cannot use Osaifu-Keitai. be made.
Page 41
nano UIM card Security Codes R emoving nano UIM card You can set the security code named PIN Detach the back cover (P36) in nano UIM card. "0000" is set at the time Remove the battery pack (P47) of subscription. Customers can change PIN afterwards. For details about PIN of nano UIM Remove the microSD card (P199) card, refer to "PIN code" (P185). Put the fi nger in the groove on the end on nano UIM card slot, and pull I nserting nano UIM card the nano UIM card in the arrow D etach the back cover (P36) direction (a) Remove the battery pack (P47) Take out the nano UIM card straight in the arrow direction (b) Insert the nano UIM card into the nano UIM card slot all the way to the end in the arrow direction with the IC chip facing down Confi rmation and Settings before Using...
Page 42
A ttaching Battery Pack Note • When handling the nano UIM card, be Detach the back cover (P36) careful to not touch the IC chip, or get it With the battery pack mark facing scratched. • Note that the nano UIM card may get up, align the convex part of the damaged if you attach or remove it terminal with concave part of the forcedly. battery pack correctly, press the • Do not lose the nano UIM card you battery pack to the direction a and removed. push it to the direction b B attery Pack • Please use the dedicated Battery Pack L24 for this terminal. • Make sure to turn off this terminal beforehand and hold it in your hand when attaching/ removing the battery pack or the back cover so that the display does not get damaged. • Do not bend or twist the back cover forcedly when attaching or removing it. The back cover may get damaged.
Page 43
R emoving Battery Pack C harging Detach the back cover (P36) B attery Charge Hold the battery pack up in the direction of arrow mark using the • For detailed information, refer to instruction manuals for AC Adapter 05 (optional) and DC concave part of the terminal with Adapter 04 (optional). your fi ngertip, and then remove it • AC Adapter 05 can be used from AC 100 V to 240 V. • The shape of AC adapter plug is for AC 100 V (Japanese specifi cation). A conversion plug adapter for the destination country is required when using an AC adapter compatible from AC 100 V to 240 V. Also do not use a transformer for overseas travel to charge. • When the terminal is turned ON, you can operate the terminal even while charging. However, in that case, charging takes longer time because of reducing charging volume. • Do not apply excessive force when inserting or pulling out the connector. Insert or pull it ...
Page 44
• Make sure to remove it from the power plug B attery Pack Life of AC adapter after fi nishing charging. • When charging with unstable rated voltage, • Battery pack is a consumable supply. The battery may not get charged or charging may usage time decreases gradually each time fail. the battery is charged. • When the usage time becomes about half Do not charge for a long time (for of a new battery, life of the battery pack is several days) assumed to be over. We recommend you to replace the battery pack ahead of time. • If the terminal is left for a long time after Also, depending on the usage condition, being fully charged, the battery pack starts the battery pack may get swollen when the feeding the terminal when the charging is battery life is running out. Note that it is not complete. For that reason, the actual battery a problem. time may shorten and the battery may be • Watching TV, etc. for along time while used up. If this happens, please charge it charging may aff ect battery pack life. again correctly. Before recharging, remove this terminal from AC adapter and reset. ...
Page 45
When charging is completed, remove C harging with AC Adapter the power plug of AC adapter from It describes how to charge this terminal with the power outlet AC Adapter 05 (optional). Remove the microUSB plug of AC adapter horizontally from this terminal ■ DC Adapter 04 The DC adapter supplies power to charge this terminal through a cigar lighter socket (12 V/24 V) in a vehicle. Insert the microUSB plug of AC adapter into the microUSB connection terminal of this terminal horizontally with the side of B mark facing up Raise the AC adapter power plug and insert it into power outlet • During charging, Notifi cation LED light of this terminal turns red color and blinks. • When charging is fi nished Notifi cation LED light turns green color, a ringtone rings to notify that charging is over, and is displayed. Confi rmation and Settings before Using...
Page 46
C harging with a PC P ower On/Off Connect this terminal to a PC by the microUSB Cable 01 (optional) to charge. P ower On Insert the microUSB plug of microUSB Press and hold the power key for Cable 01 into the microUSB over two seconds connection terminal of this terminal • This terminal vibrates and the lock screen • Insert the microUSB plug horizontally with is displayed after a while. the side of B mark facing up. • After purchasing this terminal, when it is Connect the USB plug of microUSB turned on for the fi rst time, follow the on- Cable 01 to the USB port on PC screen instructions to perform the initial • If a request of installing a device driver settings (P64). appears on your PC, cancel it. • If the "Install PC programs" screen is ...
Page 47
T urning on Backlight Unlocking Screen To prevent unwanted operations and to save When turning on the power or when displaying power, the backlight turns off after a certain the display, the touch screen stays being time duration you set up and the screen is locked. locked after then. Swipe the screen up, down, left or Press the power key right • Backlight lights on and the lock screen is • You can change the method of unlocking displayed. the screen (P175). • Press power key again to black out the Note backlight and lock the screen. ■ KnockON/KnockOFF • When the screen lock is set to "Touch" Quickly tap the blacked-out screen twice or "Swipe", drag or swipe the status bar to light the backlight. Quickly tap the downward with the screen locked to open area with no icon on the Home screen* or the notifi cation panel. lock screen, or tap the status bar twice to turn off the backlight. * ...
Page 48
Lock Screen B asic Operations This terminal adopts touch screen which allows you to operate by touching the display. U sing Touch Screen P recautions on using touch screen The touch screen is designed for fi nger touching lightly. Do not press it hard with your fi nger or with sharp objects (fi ngernail, ballpoint pen, pin etc.). The following actions may cause the touch screen not working properly. Note that it may cause wrong operations. • Operating the screen with gloved hands • Operating the screen with tip of a fi ngernail • Operating the screen with an object on it • Operating the screen with a protective sheet Date & time, current location or seal on it Notifi cation information display area • Operating when the screen is wet Displays the details of two latest notifi...
Page 49
■ Flick : Touch the screen and quickly T ouch screen operations sweep your fi nger The following operations are available on the • Flick so that the screen touch screen. scrolls at high speed. While scrolling, touch the screen ■ Tap : Touch the screen lightly to stop scrolling. ■ Double tap : Touch the screen lightly twice in a row ■ Touch and : Touch the screen for over one hold second ■ Swipe : Flick the screen lightly • ...
Page 50
■ Pinch-in : T ouch the screen with two Back key fi ngers apart and then move Tap to go to the previous screen. them together, as if pinching Close a dialog box, an option • Pinch in to reduce the menu, the notifi cation panel or screen. the on-screen keyboard. Home key Tap to display the Home screen. History key • Touch to display the most recently used applications. • Touch and hold to display the current screen or the option menu performable in H ome Touch Buttons application. Notifi cations key You can change the layout and the color of the Tap to displays/hide the home touch buttons, you can also display/hide notifi cation panel. the home touch buttons of the application in use.
Page 51
A uto Rotating Screen Q Slide Apps This terminal screen automatically rotates to While doing other operations, video, Internet, landscape or portrait views, depending on the messaging, calendar and email can be used via direction in which it is turned. popup. • Depending on the display screen, the screen • Up to two QSlide apps popup windows can be orientation may not change on this terminal. displayed on the same screen. • Even if this terminal is oriented close to being Using QSlide apps level in relation to the ground, the landscape/ portrait view does not change. Open the notifi cation panel (P70) From the Home screen, "Apps"X "QSlide" "Settings" X "Display" • The QSlide application fi eld is displayed Place a check mark in "Auto-rotate on the notifi cation panel. screen" Select QSlide apps ...
Page 52
Go to full screen display/previous size and E mergency Mode display it. Enable this mode to restrict the terminal Adjust background transparency. settings and functions to save the battery If this is dragged to the left, even if the power. QSlide apps screen is touched, it will no longer respond, but other functions can be Enabling emergency mode used. Close the QSlide apps. Press and hold the power key for Adjust the display size. over two seconds "Emergency mode" X confi rm the Editing QSlide apps contents on the screen X "OK" Open the notifi cation panel (P70) • Restart this terminal and enable the Tap "Edit" in the QSlide apps fi eld emergency mode. • You can customize the items displayed Note in the QSlide apps sorting or in the notifi cation panel. • Even if the emergency mode was enabled only once, from the next time on the Home screen, tap "Apps" X "Disaster ...
Page 53
Disabling emergency mode 10key keyboard/QWERTY keyboard ● 1 0key keyboard Press and hold the power key for It is a keyboard similar to a general mobile over two seconds phone keyboard (for multi-tap method). Tap "Emergency mode" X "OK" a key assigned character you want to enter several times until the target character is • From the Home screen of the emergency entered. mode, tap "Stop saving" X "OK" to disable the emergency mode. • Restart this terminal and disable the emergency mode. C haracter Entry This terminal has an on-screen keyboard that is displayed in the touch screen for character ● O n-screen QWERTY keyboard entry. The array is the same as the PC's keyboard. Enter Japanese in Roman character. C haracter Entry via On- screen Keyboard If you tap a text box on the screen, the on- screen keyboard appears in the touch panel. ...
Page 54
(10key list. For 10key keyboard, right click to keyboard) to switch "10key keyboard" display pictograph/symbol/emoticon/ and "QWERTY keyboard". pictogram-D list. - Tap to display handwriting input • Display alphanumeric characters and kana keyboard. when " 英数カナ (Alphanumeric and Kana - Tap to display clipboard. key)" is displayed. - Tap to display "LG Japanese keyboard" • Touch and hold down to enable Input menu. The voice typing key can be Extension plug-in. (P63) hidden in the "Keyboard Settings". / Switch character mode is displayed when setting to hide. • Switch the character mode. * For detailed operations, refer to "Help" • Touch and hold down to select "Input in "Keyboard Settings".
Page 55
Delete key Shift key • Delete the character on the left of cursor. When entering letters, tap to switch to • Touch and hold down to delete the capital letters. characters continuously. : Small letters : Only capital letter with the fi rst letter Right cursor key : All capital letters • The highlight moves to the right. • Touch and hold down to move it Punctuation mark key continuously. • Input punctuation marks. • It can also widen the conversion range. • Touch and hold down to display symbol list. Space key/Convert key • Enter a space. O n-screen 10key keyboard (arrow • " 変換 (convert)" is displayed during key mode selected) Hiragana input and a list of conversion candidates is displayed. Confi rm key/Execute key/Link feed key/ Search key/Next key/Finish key • ...
Page 56
Quick cursor key H andwriting converting keyboard Move the cursor to the beginning or the end of a sentence. Select all Select all the characters. Copy key Copy the selected text. Paste key Paste the copied/cut text. Delete key • Delete the character on the left of cursor. • Touch and hold down to delete the Handwriting area characters continuously. • is displayed under the characters when Select/Deselect key writing characters. Tap to display a • Select a target. list of recognition candidates and you can • You can change the area with arrow key. modify the character. • With deselect key, you can deselect the • is displayed on the right side of the selected area. handwriting area when writing characters. Tap to continuously input the Space key characters by handwriting. Enter a space.
Page 57
Symbol key Delete key Display a list of pictographs, symbols, • Delete the character on the left of cursor. emoticons and pictogram-D list. • Touch and hold down this to delete the characters continuously. Keyboard type key/clipboard key/setting • When you are writing characters in handwriting input fi eld, you can delete all • Switch to the software keyboard that the characters, one character or a line was displayed prior to the handwriting within the fi eld. converting keyboard display. • Touch and hold down to display clipboard Note key and setting key. • The key display varies depending on the Space key entry screen or character mode. Enter a half space. • When you no longer need the keyboard, Left cursor/Right cursor you can close it by tapping . To display • Move cursor position. it again, tap the text box on the screen. • Touch and hold down left cursor key to switch to arrow key mode.
Page 58
C hanging Character Entry Touch When inputting characters, feedback set key popup, sound and Settings vibration, etc. Touch and hold down on a character entry Voice input Set if enable voice input or screen and tap to display "LG Japanese not. keyboard" menu. Tap "Keyboard Settings" to change the character entry settings. Handwriting Set handwriting settings. 10key Set fl ick input and auto COMMON SETTINGS keyboard cursor movement. Input Set the input language, Fullscreen Set to display the dedicated language and screen orientation and the mode input screen or not in keyboard keyboard type of each input landscape view. type mode.
Page 59
EXTERNAL APPLICATION ABOUT IME I nput Set to use Input Extension Help Display Help of LG Japanese Extension plug-in or not. keyboard. plug-in • To use Input Extension In Help, you can confi rm plug-in, download descriptions of function key "WnnDictionary" (search in usage, Split keyboard and dictionary) / "WnnBrowser" One-handed operation mode. (connect to URL) / Keyboard Detailed information on "WnnSearch" (search version LG Japanese keyboard is inside Website). For details displayed. about download, refer to "Downloads" (P245). DICTIONARY User Edit words in personal dictionary dictionary. Clear Delete all learning learning ...
Page 60
rst time, follow the on- • When the operation guide of Home screen instructions to select a language, set screen is displayed, tap "Don't show this the Google account or perform the service again"/"OK" to display the Home screen. initial settings. • Procedures diff er depending on the connection with network and setting skips. Tap "Next" on "Welcome" screen • Tap " 日本語 ( 日本 ) (Japanese (Japan))" to change language. • Follow the on-screen instructions to set up the items below, and tap "Next". ® - Wi-Fi - Google account - Google service - If gathering the log information to LG is allowed or not On the "Software Update" screen, "OK" Confi rmation and Settings before Using...
Page 61
N otifi cation LED Note • You can change the settings later. • Before setting online service, make About Notifi cation LED Light sure that the data can be connected (LTE/3G/GPRS), or make sure that the This terminal notifi es you of its status via the ® Wi-Fi network is being connected. lighting up or blinking Notifi cation LED light. • Even when the Google account has Operations of Notifi cation LED light is shown not been set up, you can still use this below. terminal except for the usage of Google • Slowly blinking green color: Incoming call service such as Gmail or Google Play. • Quickly blinking green color twice: Missed call/SMS • Blinking red color: Area Mail notifi cation • Blinking rainbow color: Alarm notifi cation • Lighting up red color: Charging • ...
Page 62
Setting Notifi cation LED Light S creen Display/Icons From the Home screen, "Apps" X "Settings" X "Display" X S tatus Bar "Notifi cation LED" The status bar is displayed at the top of the screen. The status and notifi cations of this Turn on "Notifi cation LED" terminal are displayed on the status bar. On Place a check mark in features to status bar, notifi cation icons are displayed on get notifi cations the left side, and status icons are displayed on the right side. Note • The notifi cation display of Area Mail and alarm cannot be changed. Confi rmation and Settings before Using...
Page 63
M ain status icons Airplane mode activated nano UIM card locked or nano Signal strength UIM card not inserted No service Manner Mode (vibrate only) ® (grey) Bluetooth function is on Manner Mode (Do not disturb) ® Connecting to a Bluetooth Alarm is set (white) device Reader/Writer, P2P function is During international roaming 3G available/communicating Calling via hands-free / (arrow is gray in standby, white Synchronizing data while sending/receiving) LTE available/communicating GPS is positioning / (arrow is gray in standby, white NFC/Osaifu-Keitai lock is set on while sending/receiving) both this terminal and nano UIM ® Connecting Wi-Fi card / communicating NFC/Osaifu-Keitai lock is set on ...
Page 64
Main notifi cation icons Playing music via music application New Gmail Playing music via Media Player New Email Detected an Open Network (Wi- ® New message (SMS) ® Connecting to the Wi-Fi of New Area Mail unavailable Internet Problem with message (SMS) Connecting with USB delivery Charging completed New Hangouts message Slow charging Incoming call, making a call*, answering a call* Low free space of memory on this terminal Receiving a video call or talking on the phone* Data upload completed Missed call Data download completed New answering memo Problem with login New voicemail message Available to update New alarm notifi cation Application installation fi nished Upcoming calendar event Watching 1Seg Confi...
Page 65
Recording TV (Full seg/1Seg) charged with a PC instead of the AC Recording TV (Full seg/1Seg) is adapter (optional). fi nished • is displayed, the battery charge speed is slower than the speed when More notifi cations charging with AC adapter (optional). • is displayed when the internal storage Connecting VPN runs out of space. ® • is displayed, you may not be able Wi-Fi tethering available to install an application even after USB tethering available downloading it. Make enough free space and install the application again. ® Bluetooth tethering available ® Connecting Wi-Fi Direct Face is recognized via Smart screen (backlight is lit up) The application provided by LG Electronics Inc. needs to update Battery saver is on * Displayed when changing to another screen such as Home screen. Confi rmation and Settings before Using...
Page 66
Date & time N otifi cation Panel Display date and time. You can confi rm the notifi cation icons, start Quick setting icon fi eld an application or turn on/off a function in the Switch each function on/off . notifi cation panel. • ON is displayed in aqua color, OFF is displayed in gray color. V iewing notifi cation panel • Scroll to right and left to display the hidden icons. Drag or swipe the status bar • Touch and hold down to display the downward setting menu screen of each function. • Touch "Edit" to customize or sort icons. QSlide App fi eld Tap and activate QSlide app (video, Internet, message, calendar, Email, fi le manager, calculator).
Page 67
Telecommunications carrier name/SIM Sorting quick setting icons carrier name Tap "Edit" in the quick setting icon On the left, the name of currently connected telecommunication carrier is displayed; on fi eld the right, the carrier's name read from nano Drag the items you want to sort UIM card is displayed. to the destination Setting button The "Settings" screen is displayed. C ustomizing quick setting icons Delete notifi cation Delete notifi cation information and icons. Tap "Edit" in the quick setting icon Some notifi cations cannot be deleted. fi eld Place a check mark in the desired V iewing notifi cation details item to display Tap the notifi cation information on the notifi cation panel • The notifi cation details are displayed in an appropriate application.
Page 68
Changing to photo icon C ustomizing icons You can use a photo from camera and gallery You can change the icon design such as as the icon for the Home screen. shortcut to use on the Home screen. From the Home screen, touch and Note hold down a shortcut icon • From the Home screen, "Apps" X • is displayed at the upper right of the "Settings" X "Home screen" X "Select icon. Home" X usable only when "Home" is Tap the shortcut icon again selected. • Icon change screen is displayed. "Add new" X drag the frame and set Changing home application icon icon size X "OK" • Gallery is activated. From the Home screen, touch and From Gallery, select a picture you hold down a shortcut icon want to set up X adjust its size X • is displayed at the upper right of the "OK" icon. Tap the shortcut icon again • Icon change screen is displayed. Tap your favorite icon X "OK" Confi rmation and Settings before Using...
Page 69
H ome Screen Note • Pinch out the Home screen to enlarge the wallpaper till it becomes full screen. V iewing Home Screen Pinch in the wallpaper enlarged till it becomes full screen to return to the Home screen. Home Screen Management A dding Home screen Pinch in on the Home screen • Home screen list is displayed. "+" • Up to seven screens can be added. Note Widget • Touch and hold the Home screen you Machi-chara want to delete X drag it to the "Remove" on the top of the screen and delete the Apps Home screen. Current location of the Home screen Flick to right/left to switch the display. Dock Always displayed even when the Home screen is changed. Confi rmation and Settings before Using...
Page 70
A dding an application or widget D eleting from the Home screen of an application or widget From the Home screen, touch and hold down an area with no From the Home screen, touch and application icon or widget hold down a desired application icon or widget to delete "Apps" or "Widgets" Drag the item to "Remove" on the Tap a desired application icon or top of the screen widget to add C hanging wallpaper M oving an application or widget From the Home screen, touch From the Home screen, touch and and hold down an area with no hold down a desired application icon application icon or widget or widget to move "Wallpapers" X "Gallery"/"Live Drag the item to the destination wallpapers"/"Multi-photo"/"Photos" or select a wallpaper from Disney Note wallpaper list • You can drag the icon rightward or • When "Gallery"/"Live wallpapers"/"Multi- leftward till the edge of the screen to ...
Page 71
A pps List A pps Screen Some applications require a separate subscription (charge). V iewing Application Screen Applications not included in the folder From the Home screen, "Apps" Disney マー In Disney Market is a ケッ ト (Disney convenient portable Market) application where you can obtain various "Disney apps" and the recommended information. (P119) Disney Lines up the best Cinema video contents from popular live action movies to animation works provided by Disney! This is the premium video service only for you. "Apps" tab "Widgets" tab "Search" button "Menu" button Application icon list Confi...
Page 72
® Disney Mail A Deco-mail opening the mickey Maker converter app which window cover. can be activated from Window Play or pause the mail.It activates alone Music* music without opening to create and link the mickey window ® Deco-mail as well! cover. Disney KS1604 Special Window Check the number Welcome welcome movies only Steps* of steps, distance for users! Enjoy the traveled, and calories adorable welcome burned without message voice from opening the mickey Mickey and Minnie. window cover. Confi rmation and Settings before Using...
Page 73
Window Select a Disney Fantasmic! "Fantasmic!" is an Setting* character and animated wallpaper change the window of the colossal night image, live wallpaper, entertainment in which ringtone, etc. of the Mickey who turns into mickey window cover sorcerer's apprentice collectively. battles on the stage in the Mediterranean Tokyo Disney An app to check your harbor. ® Resort present location on Machijikannabi the map of Tokyo Disney アラーム A cute and convenient Disneyland/Tokyo (Disney application which has DisneySea and get Alarm) three functions of various information alarm, world clock and such as waiting time timer with adorable for attraction.
Page 74
Calculator Four arithmetic Clock Set settings of alarm, operations are timer, world clock available. (P156) and use stopwatch. (P150) Settings Set various settings. (P157) QMemo+ You can simply write a memo without having Chrome Google web browser to launch Memo application. application. You can Maps Check current location also input texts or or search a destination illustrations directly on with Google Maps. the captured screen. (P149) (P155) Gallery View or sort still Osaifu-Keitai It allows you to pay images (photos) and money only by holding videos. (P144) the terminal over an IC card reader in stores YouTube Play or post videos. etc. (P122) Watch Full seg/1Seg. ...
Page 75
Downloads Confi rm, display or Google+ Use Google SNS. play the downloaded Play Movies & Purchase videos from data. Google Play. Email Setup Email account Play Books Purchase books from to send/receive Google Play. emails. (P107) Play Games Purchase games from Twitter Offi cial Twitter client Google Play. application. Publish short message on the Drive Save images or videos site to communicate to Google Drive or with others. share them. Play Store Download the Photos View pictures and application from movies. You can also Google Play. (P120) sync with Google Photos to backup Google images and share ...
Page 76
• Some of the applications may not show Sheets Create and edit a its name fully below the icon. Sheets. You can also edit with other users. Slides Create and edit a Managing Applications presentation. You can also edit with other A dding an application to Home users. screen Applications not included in the folder From the Home screen, "Apps" Instruction Instruction manual for Manual this terminal. Available Touch and hold down the application to activate a desired icon to add it to the Home screen function directly from Drag it to the desired position and the description. release your fi nger * This application is used in the supplied • The application is added to the Home Mickey Window Cover L01. screen. Note U ninstalling an application • ...
Page 77
Window Screen Note • The notifi cation icon will not be displayed Attach the Mickey Window Cover L01 to this after two seconds. terminal and close the fl ip section to display the window screen. You can use an application or answer a phone call, etc. through window Available Application screen. • It is necessary to turn on "Mickey Window Swipe the main screen up, down, left Cover" in the setting menu of this terminal or right (P194). Tap the application that you want to use • When the screen backlight is blacked out, execute the KnockON (quickly tap the screen twice) to turn on the backlight. Main Screen Camera application Start the camera to take photos or preview the images you took. • Tap the screen or press the volume key (up)/volume key (down) to take photos. Date Window setting application Weather Select a Disney character and change the Notifi cation icon window image, live wallpaper, ringtone, etc. of the mickey window cover collectively. Clock Confi...
Page 78
Music application Available Functions Play music, pause, etc. • Select a music to play via the music Answer a call* You can answer a voice application beforehand. call. Also you can end/hold Pedometer application a call. Check the number of steps, distance • Although notifi cation traveled, and calories burned. screen for video call is • Set up your height, weight, step length displayed, you cannot and your objective in advance to count it answer it. Open the fl ip even more correctly. section and follow the on- Weather application screen instructions. Check the weather, temperature and Notifi cation for precipitation probability of the current When there is a missed miss calls* location or the place you set. call, the notifi cation icon will be displayed. Note Notifi cation/ When a mail (mail/email) ...
Page 79
Cancel auto (P194) T ask Manager lock Confi rm/end the running application. Stop alarm Stop the alarm. *1 During voice call, the window screen • Tap an thumbnail to start the application. backlight blacks out two seconds after the • Scroll/fl ick the thumbnail to right or left call started. to delete it from the list. *2 The notifi cation icon of a missed call/new • Tap "Clear all" to end all the activated message/new Email will not be displayed applications. after two seconds. After the window screen • Tap "×" on the thumbnail end that backlight blacks out, the notifi cation icon application. will be displayed after lighting up again. Confi rmation and Settings before Using...
Page 80
C alling "Phonebook" button M aking a Call Activate "phonebook" application. From the Home screen, "Phone" X "Dial" tab: The dial screen is displayed. "Dial" tab "Recent calls" tab: Recent calls screen is displayed (P93). "Favorites" tab: Contacts list added to the Favorites is displayed. Phone number entry fi eld Display an input phone number. Dialpad Call button Menu Display menu. Delete button Delete a number at the far right. To delete all numbers entered, touch and hold the key. "Register" button Register the entered phone number to phonebook. Calling...
Page 81
Enter a phone number X - Since it is a best eff ort communication ■ When making video call (the optimum communication speed X "Video call". changes depending on the network traffi c), the image quality diff ers Tap "End call" to end a call depending on the network environment. - When you could not switch to video Note call from voice call, a notifi cation will • You can make voice calls and video calls be shown on the display indicating that in high quality with VoLTE. To use VoLTE, the switching to video call failed, and you and the other party both need to voice call will continue. meet the following conditions. - As the display processing is diff erent - The device supports VoLTE. for each phone model, your image - It is within the XXX area (You cannot displayed on the terminal for the video ...
Page 82
Adding a standby ";" E ntering a Pause After calling, a message is displayed to confi rm Use "Add 2-sec pause" or "Add wait" to dial the number you dialed of a desired service. phone number and additional code in a row From the Home screen, "Phone" X when sending an additional code during a call "Dial" tab is required for bank balance inquiries, ticket reservation services, etc. Enter a phone number X X "Add wait" Adding a two seconds pause "," • A semicolon ";" is displayed behind the Automatically dial a service number two- phone number. second pause later after calling. Enter a menu number of a desired From the Home screen, "Phone" X service X "Dial" tab When a confi rmation message is Enter a phone number X X "Add displayed, "Yes" 2-sec pause" • The push signal will be sent • A comma "," is displayed behind the phone automatically. number.
Page 83
E mergency Call However, if the agency you called considers your location information and phone number necessary for important Emergency call Phone number purposes such as life saving, the Police agency can retrieve them regardless of your mobile settings. In addition, the Fire department or introduction area and introduction timing ambulance service of "Location notifi cation of emergency Japan Coast Guard call" vary depending on the readiness of the agency you called. • When you are making an emergency call Note (110, 119 or 118) from this terminal, be • This terminal supports "Location sure to notify that you are calling from a notifi cation of emergency call". When mobile phone and give both your mobile dialing an emergency number such as phone number and present location 110, 119 or 118, information of the place clearly as the police or fi re department where you called (location information) is may call you back for confi rmation. Stay automatically notifi ed to the agency that where you are to ensure that your call ...
Page 84
• In Japan, when nano UIM card is not R eceiving a Call inserted in the terminal, the emergency numbers of 110, 119 or 118 are not F or Voice Calls available on the PIN code entry screen or during PIN code lock/PUK lock. When there is an incoming call • If you make an emergency call 110, 119, 118 with call rejection setting enabled, • For VoLTE, "(high-quality sound)" is call rejection setting/Blocking mode will displayed. be disabled. • Answering memo recording: X "Play • You may not be able to make an emergency reply message" call on some networks. • Put a call on hold: X "Put a caller on • You can not make emergency calls with hold" video calls. • Stop ring tone, vibration: press power key, or volume (up)/volume (down) X "Accept" • ...
Page 85
F or Video Calls I ncoming Call While Activating an Application When there is an incoming call If there is an incoming call while activating an • "(high-quality sound)" is displayed. application, the popup screen will be displayed • Rejecting a call: X "Reject call with on the top screen. Tap "ACCEPT"/"ACCEPT SMS" VIDEO" to start the call. • Answering memo recording: X "Play • When the popup incoming screen is displayed, reply message" if the caller's name or the phone number • Put a call on hold: X "Put a caller on area is tapped, the incoming call screen (full hold" screen) can be displayed. • Self image is not being sent to the other party: X "Camera OFF response" ■ Incoming voice call • Stop ring tone, vibration: press power key, or volume (up)/volume (down) X "Accept video"...
Page 86
C alling/Sending an SMS to a O perations during a Call Missed Call The following operations are available while talking on the phone. When you have a missed call, you can check • Press the volume key (up)/volume key (down) the notifi cation from status bar. during a call to adjust the volume. If appears in the status bar, drag or swipe the status bar downward F or Voice Calls • Missed call notifi cation appears on the notifi cation panel. "Missed call"/"CALL"/"SEND SMS" • "Missed call": Recent calls are displayed. • "CALL": Make a call. • "SEND SMS": Message input screen is displayed. Compose a message and tap "Send" to send the message. High-quality sound indication Appears when using a call with high quality sound of VoLTE. Calling...
Page 87
Name and phone number F or Video Calls End a call. Dialpad Display dialpad and send push signal (DTMF tone). Hold * Put a call on hold. Add call * Call another party. Call duration Mute * You voice cannot be heard by the other party. Speaker * You can hear the other party's voice through speaker to talk hands-freely. High-quality sound indication Switch to video Appears when using a call with high quality Switch to video call. sound of VoLTE. *1 Tap again to return to the previous state. *2 Subscription is required for "Call waiting". The other party's image Depending on the other party's setting, a substitute image may be displayed. • When the other party's image cannot be received, appears. Your own image Calling...
Page 88
Switch cameras Note Switch the cameras for the image to send • While talking on a video call, tap the video to the other party from the front side or back screen to switch between display video side. full screen and cancel full screen. • While talking on a video call, if the End a call. application is switched from "Phone", the Menu video will not be sent to the other party Display the menu for calling screen. any more. • X tap "Switch to voice call" to switch to • While talking on a voice call, if the other voice call. party switch it to the video call, a popup • X tap "Dialpad" to turn off the camera screen will appear to confi rm that it has and display the dial screen. been switched to video call. Tap "Allow" • X tap "Switch audio output destination" so that it becomes video call screen. to switch audio output ports. • X tap "Camera OFF" to stop sending video to the other party. • X tap "Switch video area" to switch "Your own image" display area and "The other party's image" display area.
Page 89
Phonebook C all Logs Activate "phonebook" application. On the Recent calls screen, you can check logs of dialed calls, received calls, missed calls "Dial" tab: The dial screen is displayed (P84). in the list. "Recent calls" tab: Recent calls screen is • Up to 500 items can be displayed. displayed. From the Home screen, "Phone" X "Favorites" tab: Contacts list added to the "Recent calls" tab Favorites is displayed. Switch logs • Switch display between Incoming and Outgoing. • Tap "All" to display all incoming/outgoing call logs. Name, Phone number, Call date and time • Tap to open the Recent calls screen. Tap an item on the Outgoing screen to make a call, send an SMS, make a video call, save in the phonebook, show profi le screen, etc. • Touch and hold an item to set "Edit number before call", "Delete from call log", "Register as blocked number", "Register to Favorites", "Search location", etc. Menu Display menu.
Page 90
Voice call key A nswering Memo Make a voice call to the number in the call log. When you cannot answer a call, playback reply message and record an answering memo. Deleting History From the Home screen, "Phone" X X "Call settings" From the Home screen, "Phone" X "Answering memo" "Recent calls" tab Place a check mark in "Answering X "Delete log" memo" Place a check mark in the history • "Answer time": Available to set from 0 to to be deleted or in "Select all" X 120 seconds. "Delete" X "Delete" • "Reply message": Set a reply message • The history is deleted and it goes back to during an incoming call. "Recent calls" tab screen. Note • You can record a piece of answering memo up to 60 seconds with total 20 pieces of answering memos. However, if there are answering memos which have been played, when saving the next answering memo, those which have been played are deleted from the oldest one so that the new one can be saved.
Page 91
• To check the answering memo you C all Settings recorded, drag or swipe the status bar Set call settings. downward with displayed on the status bar X "New answering memo", or from From the Home screen, "Phone" X X "Call settings" the Home screen tap "Phone" X X "Call settings" X "Answering memo" X "Play answering memo". Tap a answering memo V oice mail Set to activate/ Network to playback and tap again to stop playback. service* deactivate this service. service • To delete the recorded answering memo, C all Set to activate/deactivate from the Home screen, "Phone" X "Call forwarding this service, or change settings" X "Answering memo" X "Play service* forwarding number. answering memo" X ...
Page 92
Network Call A missed call is notifi ed SOUND & VIBRATION SETTINGS service notifi cation by SMS when the Phone ringtone Set phone ringtone. power is off , when you Vibrate on ring Set to vibrate or not are out of service or with an incoming call. when it is unavailable to receive a call. Dialpad touch Set to turn on dialpad tones touch tone or not when English Guidance such as voice tapping dial pad. guidance guidance or Network service guidance is INCOMING CALL SETTINGS played back in English. Answering memo (P94) R emote Set remote operation R eject call setting Reject unregistered ...
Page 93
OTHER SETTINGS P honebook C all mode setting Set whether to use Manage various contact information such as VoLTE when VoLTE names, phone numbers or mail addresses using calling is available. "phonebook" application provided by XXX. • For using the cloud service on phonebook, Call time Display or reset the phonebook application is required. cumulated call time. • When you activate "phonebook" for the Set whether to reset fi rst time (including after resetting the the cumulated call time application), "Use of Cloud" screen appears on the fi rst day of each and set to use Cloud. month. Contact Inquire about R egistering to Phonebook malfunctions, loss/ theft while overseas. Register a new contact.
Page 94
Account A saving account appears. • Tap "Set" to select an account. Image fi eld Tap "Set" to register an image. To take a photo, tap "Take photo". To select a saved image, tap "Select picture". Last name, fi rst name Label key Select a content label (item). Input fi eld Input phone number, mail address, address, etc. Ring tone setting button Add other items Input the address, nickname, memo, etc. "Save" Calling...
Page 95
Photo set in the phonebook C onfi rming/Using Contacts By tapping the other party's image registered in the phonebook and then tapping the icon, From the Home screen, "Apps" X you can make a call, create SMS or email, etc. "phonebook" Register (P97) • A contact list screen appears. Add new contacts. • If you have registered more than one account, select one to add a new contact to and complete the required items. Start/Stop synchronize cloud Menu Display menu. "My profi le" tab (P102) Profi le screen appears. You can check the phone number, edit/manage your own profi le information. "Group" tab (P101) Tap to select a group and display the contacts in groups. Index character display area Tap "Index" to display index characters by which you can search a name in the order of " C ontacts" tab the Japanese syllabary, alphabet, etc. Display the contact list screen. Index Name registered in the phonebook Display the index character display area.
Page 96
Tap a contact to confi rm or use D eleting Contact • Profi le screen is displayed. From the Home screen, "Apps" X • Tap "Edit" to edit contacts. • Tap in phone number fi eld to make a "phonebook" X "Contacts" tab call. Or tap the phone number to create Tap a contact SMS or make video call. • To create a mail, tap a mail address and X "Delete" X "OK" select an application. Note C hange Displayed Account • On "Contacts" tab, X "Delete" X "Select on Phonebook all" or place a check mark in the contact you want to delete X "OK" X "OK". You can set to display or to hide the contacts included in a group of a specifi c account or a Google account. From the Home screen, "Apps" X "phonebook" X "Contacts" tab X "Settings" X "Accounts to display"...
Page 97
Adding contacts to group A dding/Editing a Group From the Home screen, "Apps" X From the Home screen, "Apps" X "phonebook" X "Group" tab "phonebook" X "Group" tab Tap a group X "Add member" X "Add group" place check marks in the contacts ■ To edit a saved group to add X "OK" X "OK" Tap a group you want to edit X "Edit" X Edit and then tap "OK". Note ■ To delete groups X "Delete group" X place check marks • Only contacts saved in account or in the groups you want to delete X "OK" Google account can be added to the X "OK". group. ■ To change display order of groups "Sort" X Tap a group X Drag the group to Deleting contact from group a desired place X "OK". Select an account X Enter a group From the Home screen, "Apps" X name X Select an icon and color "phonebook" X "Group" tab "OK" Tap a group X "Delete member" X ...
Page 98
• When multiple contacts data (vCard) R egistering My Profi le are saved in the microSD card, a phonebook selection screen appears. You can confi rm your phone number, and add, Follow the on-screen instructions to edit or delete your profi le information. select import method. From the Home screen, "Apps" X ■ To export contacts "phonebook" X "My profi le" tab Tap "Export to SD card" X Select export "Edit" X Enter the required items X method X "OK" X Operate following the on-screen instructions. "Save" ■ To send as contact data (vCard) "Share phonebook data" X Select a I mporting/Exporting Contacts sending method. Import contacts or send the contacts as the contact data (vCard) between nano UIM card and this terminal. From the Home screen, "Apps" X "phonebook" X "Contacts" tab X "Import/Export"...
Page 100
Mail/Web Browser S ending SMS S MS You can send/receive text message to/from From the Home screen, "Apps" X mobile phone number as a recipient. "Messaging" * For details of available number of characters, • The "Messaging" screen is displayed. etc, refer to "Short Message Service (SMS)" on website. Tap "To" box to enter a recipient's phone number • A list of contacts beginning with the entered number or name is displayed. • Tap to display phonebook and select a recipient. Enter a message in "Enter message" "Send" • The message is sent. Mail/Web Browser...
Page 101
R eceiving/Viewing SMS Note • Default message application can be From the Home screen, "Apps" X changed to Hangouts. → P182 "Messaging" • While entering a message, X "Insert • The thread (recipient who send or receive smiley" to insert a smiley. messages) list is displayed on the • To notify whether messages (SMS) are "Messaging" screen. received, from "Messaging" screen X "Settings" X "Notifi cation settings" and Tap a thread place a check mark in "Notifi cations". • A message appears. • You can also send/receive text messages to/from customers using overseas network operators. For available countries/overseas network operators, see website. • To send SMS to users of overseas network operators, enter "+" X "Country code" X "Recipient's mobile phone number". If the mobile phone number ...
Page 102
Changing SMS Settings Notifi cation Notifi cation Set ring tone when settings sound* receiving a message. From the Home screen, "Apps" X Vibrate* When receiving a "Messaging" message, set to notify • "Messaging" screen is displayed. by vibration or not. X "Settings" Repeat Set to notify alert* repeatedly or not. Change the settings if necessary Storage Set to delete the Notifi cation Notifi cations Set to display the old messages or not settings notifi cation of new when the received messages or not. messages reached maximum settings in Message When sending/ "Text message limit".
Page 103
Conversation theme Set thread wallpaper E mail and bubble style. You can set a POP3- or IMAP-compatible Email • Tap "Gallery"/ account provided by a general service provider "Camera" in to send/receive email. "Wallpaper" tab to set a still image S etting Email Account saved on this terminal or taken by Get the necessary information for settings the camera as the beforehand from your service provider. thread wallpaper. From the Home screen, "Apps" X Quick message Add/edit a phrase. "Email" • The "Select email provider" screen is displayed. Connect to URL Set to open a web page by tapping a Select a provider URL in a message or Input an Email address and its not. password, etc. Send message with When it is not ...
Page 104
D isplaying Received Email C reating and Sending Email From the Home screen, "Apps" X From the Home screen, "Apps" X "Email" "Email" • New emails are received automatically. • "Inbox" screen is displayed. On "Inbox" screen, tap an email • The message is displayed on email Tap "To" box to enter a recipient's screen. email address • A list of address beginning with the Note entered number or name is displayed. • When the acquisition interval of • Tap to display phonebook and select a "Update schedule" is set to "Manual", recipient. new messages will not be received Enter a subject in the "Subject" box automatically (P110). • Tap (Importance: normal)/ * To receive mails with "Inbox" screen (Importance: high)/ ...
Page 105
A dding an Account C hanging Email Settings You can add more than one account on "Email" Basic settings application. From the Home screen, "Apps" X From the Home screen, "Apps" X "Email" "Email" • The "Inbox" screen is displayed. • The "Inbox" screen is displayed. X "Settings" X "Settings" X "General settings" "Add account" Change the settings if necessary Select an email provider Set default Set the default account Enter an email address account settings. "Manual setup"/"Next" Select Select a download download destination for the • Follow the on-screen instructions. storage attached fi les. • Select an account type when tapping "Manual setup". Follow the on-screen Email preview Set the number of lines ...
Page 106
S etting account Load linked Set to display the image images which is linked to an From the Home screen, "Apps" X email or not. "Email" Ask before Set to display the • The "Inbox" screen is displayed. deleting confi rmation screen or X "Settings" X tap an email not when deleting an account email. Change the settings if necessary Auto- Select a screen to advance display after deleting/ DISPLAY NAMES moving an Email. Account Set account name. Resize image Set the fi le size of an name image attached to an Email. Your name Set user name. VIP settings Even when the Email Use ...
Page 107
Days to sync Set the number of days NOTIFICATION SETTINGS email* to synchronize the Notifi cations Set to show the Emails. notifi cation or not with an Message size Set message size. incoming email. limit Notifi cation Set notifi cation sound. Delete from Set the timing to delete sound server * from server. Vibrate Set to vibrate or not with Download Set to download the an incoming email. over Wi-Fi * attached fi le or not when SERVER SETTINGS ® Wi-Fi is connected. Incoming Confi rm the incoming File size ...
Page 108
Creating and Sending Gmail G mail Gmail is an online email service of Google. You From the Home screen, "Google" X can send and receive emails by using Gmail "Gmail" preinstalled in this terminal. • To use Gmail, you need to set up the mail address. When the mail address setting Enter email address in "To" box screen is displayed, follow the on-screen Enter a subject in the "Subject" box instructions to set up before implement the Gmail. Enter a message in the "Compose • For details on Gmail, from Gmail screen, X email" box Tap "Help & feedback" to refer. O pening Gmail • The mail is sent. From the Home screen, "Google" X "Gmail" • When a screen which shows new functions of Gmail is displayed, follow the on-screen instructions to operate it. Tap an email you want to read • Content of the selected email appears. Mail/Web Browser...
Page 109
Switch windows B rowser It switches to the window you selected to access to a web page in case of multiple Browser allows you to view web pages in the windows. Tap to close the window. same way that you do on a PC. Menu On the terminal, web browser can be used via ® Display browser menu (P115). a packet communication or Wi-Fi connection. Note O pening Browser • When search box and icon are not From the Home screen, "Internet" displayed on the top of the screen, scroll the browser screen downward to show • A web page is displayed. them. • Pinch out or pinch in a web page to zoom in or zoom out the display. • Even the web page is made for a PC, you Search box can also zoom in, zoom out or scroll the Tap to display the search box. Enter the text display. For detailed information, refer to or URL to search, and a list of web pages or "Touch screen operations" (P53).
Page 110
S earching a web page by voice - "Scrap": The text and web page link are saved in QMemo+ (P155). From the Home screen, "Internet" X - "Share": Send text through application tap the search box or service. - "Find": Search text inside web page. - "Web search": Search the text in • "Speak now" is displayed. websites. Speak the keyword(s) clearly to the • For details about fi le formats available microphone to display and play back on this terminal, refer to "File format" (P249). • The search keyword result list is displayed. Tap a search keyword result or "Go" • The keyword is input in the search box, and the web pages with the keyword in it are listed. Tap a web page • The selected web page opens. Mail/Web Browser...
Page 111
O pening incognito tab U sing Browser Menu You can browse web pages without leaving From the Home screen, "Internet" X any browsing history or searching history. From the Home screen, "Internet" X X Forward The next web page is • A new tab opens and the description of displayed. secret mode is displayed. New tab A new window opens and Input the search words or URL in the most frequently used the search box and display the web websites are displayed. pages Bookmarks "Bookmarks" tab is displayed. Note Add to Add a web page to • is displayed in Search box. bookmarks bookmarks. • It does not leave any history with the web page opened in secret tab. Cookie Homepage Home page is displayed. record is deleted when closing the tab. ...
Page 112
U sing Bookmark and History Save for Save a webpage. Tap X X "Saved pages" tab offl ine Add a web page to bookmarks to quickly reading to display the saved web access to the web page. page. You can display browsing history to view web Capture Capture the entire web pages your visited previously. plus page. You can check the captured image from A dding bookmark "Capture plus" in "Gallery". From the Home screen, "Internet" X Print Print out a web page, display the web pages to be added or save it as a PDF fi le to the bookmark (P212). X "Add to bookmarks" Settings The setting screen is Edit name, URL or other items if displayed (P117). necessary, and tap "OK"...
Page 113
C hanging Browser Settings From the Home screen, "Internet" X X "Settings" Change the settings if necessary General Set home page, tool bar and form auto input. Privacy and Set to display/hide security the warning screen, clear cache or browser histories, Cookies, etc. Screen and Adjust the screen or font text size. Advanced Set JavaScript validation, popup block, download storage selection, etc. or return to the initial settings. Bandwidth Set image reading. management Mail/Web Browser...
Page 115
Apps • If you subscribe charged mobile services D isney Market on a monthly basis such as Disney With Disney Market, you can download various offi cial mobile website or smartphone contents for free such as "Disney アプリ (Disney contents provided by Disney, you are ® apps)" or Deco-mails , or view recommended charged separately unless you cancel the Disney information. subscription by yourself. To cancel, from the Home screen, "Disney From the Home screen, "Disney マー マーケッ ト (Disney Market)" X X " マイペー ケッ ト (Disney Market)" ジ (My page)" X " マイメニュー (My menu)" Follow the on-screen instructions to X " 退会 (Cancel)" and follow the on-screen operate instructions to operate. • Charges may be incurred for using part of Note options for games in some apps. • ...
Page 116
* Contact 045-522-1098 from a PHS/part P lay Store of IP phones/outside of Japan or refer to (http://disney.jp/dmd/faq/) (in Japanese Google Play enables you to access applications only). and games you like and download them to install into this terminal. • To use Google Play, Google account is required (P187). I nstalling an Application From the Home screen, "Play Store" Search application X tap the application that you want to download Tap "INSTALL" (for free applications), or Amount fi eld (for paid applications) • The displayed content diff ers depending on the application. • If the application needs to access data and functions on this terminal, the functions used by the application are displayed. "ACCEPT" • For paid applications, if you have not registered a payment method with your account, additional screen for payment method is displayed. Tap it and follow the on-screen instructions. Apps...
Page 117
• You are taking responsibility when using • If you need more information about Google applications on this terminal starting Play, X "Help & Feedback" when Google from downloading and purchasing the Play screen is open. applications. Pay special attention to Note application that is accessing multiple functions or large amount of data. • Be sure to check the security of • If download or installation is fi nished application, and then install it at your own normally, the notifi cation icon will be risk. This terminal may be infected with a displayed in the status bar. Display the virus and the data may be damaged. notifi cation panel and tap the application • XXX is not liable for malfunctions, if any, name. The installed application opens. caused by the application you installed. In that case, you need to pay for repair P urchasing an application even when it is within guarantee period. • Payment for application is only once. After • XXX is not liable for any disadvantage downloading, you do not need to pay every brought to you or any third party due to ...
Page 118
U ninstalling an Application O saifu-Keitai You can use "Osaifu-Keitai compatible service" From the Home screen, "Play Store" for payment or coupon by just holding this X "My apps" X tap the application terminal and against a store reader, or " かざして that you want to uninstall リンク対応サービス (Kazashite-Link services)" for accessing information by holding it against home "UNINSTALL" electrical appliances, smart poster, etc. "OK" Electronic money and point values can be stored on IC cards, or on nano UIM card. • When the "REFUND" is not displayed on Additionally, you can check credit, balance or paid application, the trial period is expired. points of your electronic money, as well as lock Osaifu-Keitai to prevent any loss. For details about Osaifu-Keitai, refer to website. • To use Osaifu-Keitai compatible services, it is necessary to make settings through sites or applications. • If this terminal has a problem, data * in the IC card and data * in the nano UIM card may be lost or changed (if this terminal needs repair, ...
Page 119
backup services to save you important data. Using "Osaifu-Keitai • We are not responsible for damages such Compatible Service" as lost or changed data in the IC card and in the nano UIM card, or other damages related To use Osaifu-Keitai compatible services, from to Osaifu-Keitai compatible services in any the Osaifu-Keitai compatible site, download the cases including terminal malfunction or application for Osaifu-Keitai and then confi gure terminal replacement. settings. Some services do not require • If a terminal is stolen or lost, please downloading of an Osaifu-Keitai compatible immediately contact your Osaifu-Keitai application. compatible providers for what to do. From the Home screen, "Apps" X • Attach the Back Cover L40 or the Mickey "Osaifu-Keitai" Window Cover L01. NFC/FeliCa antenna is equipped on the back cover or mickey window • Obtain service information and update a cover. service list. *1 Data which is stored on the IC cards that • Initial settings may be required at the Osaifu-Keitai compatible terminals are fi rst startup. Follow the on-screen equipped with instructions. *2 ...
Page 120
N otes on Holding over Device Note • You can read/write data with reader Notes when holding over reader, NFC Modules without activating Osaifu-Keitai built-in device, etc. compatible application. • It is available even when you turn off power of this terminal. It may become unavailable if you have not turned on this terminal for a long period of time or the battery level is low. • Osaifu-Keitai compatible services can be used even if the nano UIM card PIN code cannot be unlocked, or if the PIN code is locked. • If sp-mode was not subscribed to, please • When holding over mark, bring it close to note that some of the functions of the device slowly. Osaifu-Keitai compatible services might • Hold the mark parallel to the center of no longer be able to be used. reader. If it cannot be scanned even with it held in front of the center scanner, slightly lift up this terminal, or move it backwards/ U sing " かざしてリンク対応サービ forwards or to the left/right.
Page 121
L ocking Osaifu-Keitai Note • While confi guring "NFC/Osaifu-Keitai Use "NFC/Osaifu-Keitai lock" to lock the lock", or are displayed on the status Osaifu-Keitai service from being used. Locking bar. of Osaifu-Keitai is diff erent from screen lock • This cannot be unlocked even if the and UIM card lock. power is shut off . From the Home screen, "Apps" X • If the battery runs down during the "Osaifu-Keitai" confi guring of "NFC/Osaifu-Keitai lock", "Lock Settings" X Enter a password "NFC/Osaifu-Keitai lock" can no longer be X "OK" unlocked. Be careful of the battery level. Make sure to unlock "NFC/Osaifu-Keitai • Setting password is required for the lock" after charging this terminal. When fi rst activation. Follow the on-screen the power is off , cancel "NFC/Osaifu- instructions to set password. Keitai lock" after fi nishing charging. ■...
Page 122
T oruCa Note • Packet communication fee may incur when ToruCa is an application that can be used to acquiring, displaying or updating ToruCa. collect coupon tickets, useful information etc. ® • When obtaining ToruCa via Bluetooth , it from your favorite stores. It can be obtained ® is required to turn on the Bluetooth of by many ways such as mail, website download, ToruCa application. ® Bluetooth and IC tag. Update the obtained • When obtaining ToruCa via IC tag, you ToruCa to the latest information simply. need to place a check mark in "Reader/ • For details of ToruCa, refer to website. Writer, P2P" of this terminal. → P168 From the Home screen, "Apps" X • Depending on the settings of contents "ToruCa" provider, the following functions may not be able to use. Update, ToruCa sharing, Viewing maps, Acquiring from readers • ToruCa may not be acquired from readers when Osaifu-Keitai is not initialized.
Page 123
Before Using Full seg/1Seg T V (Full seg/1Seg) Full seg/1Seg is a service provided by TV TV is an application that allows you to view broadcast companies (broadcast stations). Full seg or 1Seg, switching depending on the Receiving video and audio is free. For more reception of the airwaves. Also, interactive information about NHK reception fees, contact service using communication function of mobile NHK. devices and receiving detailed information are There are two types of information displayed in available. the data broadcasting area: "Data broadcasts" With Full seg, you can view Digital Terrestrial and "Data broadcast sites". TV Broadcasting service in high-vision quality. "Data broadcasts" are displayed by broadcast With 1Seg, you can view Digital Terrestrial TV wave for both video and audio, and "Data Broadcasting service for mobile devices. broadcast sites" are displayed by connecting For details on Full seg/1Seg service, refer to to the site provided by the TV broadcasting the website below. company (broadcast station) through the data The Association for Promotion of Digital broadcast information. Broadcasting Website: To view "Data broadcast sites", etc. packet http://www.dpa.or.jp/english communication fees are charged. Information fees may be required to access some sites. Apps...
Page 124
Broadcast Wave T V Antenna Cable L01 Full seg/1Seg is one of broadcast services, When watching TV (Full seg/1Seg), connect and receives radio waves (broadcast waves) the TV Antenna Cable L01 included in this that are diff erent from XXX service. Therefore, package with this terminal. it is not possible to receive at locations where Insert the connection plug of the broadcast waves do not reach or during time TV Antenna Cable L01 into the zones where broadcasting is off regardless of Earphone/microphone jack of this whether you are in an area with XXX service. terminal In addition, in areas with digital terrestrial TV • Insert the plug all the way till the end. broadcast service, reception may be poor or You may not be able to hear the click if it may not be available in the following locations. is not inserted till the end. • Locations far from the broadcasting tower • Insert an earphone/microphone plug of where the broadcast wave is sent 3.5 mm diameter into the earphone/ • Locations where waves are blocked by microphone jack of the TV Antenna Cable landscape or buildings such as in the L01. mountains and or near buildings • Insert an earphone/microphone plug into • ...
Page 125
• When both of the earphone/microphone ® and Bluetooth device are connected to this terminal, the sound is output from the device that has been connected later. • TV (Full seg/1Seg) is not compatible with the following functions due to copyright protection. - Video output via SlimPort supported cable or SlimPort supported accessory ® - Video output via Wi-Fi -display Note - Screenshot • The TV (Full seg/1Seg) sound is not - QMemo+ ® output on the Bluetooth devices that do - QSlide apps not support SCMS-T format. • When the TV Antenna Cable L01 alone is connected, the sound will not be output. Output the sound by any of the following ...
Page 126
W atching TV (Full seg/1Seg) From the Home screen, "Apps" X "TV" • The TV (Full seg/1Seg) watching screen is displayed. • When launching for the fi rst time, you need to select your viewing area. H ow to use the watching screen Apps...
Page 127
Program title and broadcast time Channel area • When watching a channel that supports Program details multiservice, tap to select a service. Tap it to display the program title, channel, • Tap / to switch channel. broadcast time and the overview. • Touch and hold / to search the Screen lock button available channels. Lock the TV watching screen when it is full Volume button screen display. And then tap to unlock it. Data broadcast button Speaker ON/OFF button Tap to display the data broadcast area Menu (P132). A menu is displayed. Channel list/program list area TV broadcast area Tap the channel list/program list switch • Swipe upward/downward on the right part button to display the channel list/program to change the volume. list. • Swipe upward/downward on the left part ■ Channel list to change screen brightness.
Page 128
Record/Stop button V iewing the data broadcast screen Tap to start/stop recording. Tap data broadcast button on the TV (Full • Stop button does not function for the fi rst seg/1Seg) watching screen to display the fi ve seconds after starting recording. data broadcast screen. Receiving mode button Tap the button to switch "Auto" / "Full seg" / "1 seg". Channel list/program list switch button "Using Program Schedule" → P134 Subtitles Display caption when viewing a close- captioned program. Apps...
Page 129
Data broadcast operation button ■ 1Seg • Adjust the cursor with " ▲ "/" ▼ " and tap "OK" to select an item. The broadcast data of the link displays. • Tap to return to the link. ■ Full seg • Align the cursor with an item via "∧"/"∨"/ "<"/">", and tap "OK" to select an item. The data broadcast of the link will be displayed. • Tap to display Num. To go back to the TV broadcast area previous display, tap Tap to display the TV (Full seg/1Seg) • Tap to decrease the data broadcast watching screen. operation button and display it. To go back Subtitles to the previous display, tap Display caption when viewing a close- • Tap to return to the link source. captioned program. • Tap to end the data broadcast screen. Scroll bar • ...
Page 130
U sing Program Schedule W atching Recorded Programs You can view a TV guide of both terrestrial TV programs and BS digital broadcast programs. Recorded programs can be watched and You can make reservations for recording and deleted by using the Television box. viewing. From the Home screen, "Apps" X From the Home screen, "Apps" X "TV" "TV" X "TV box" Tap the button to switch channel Tap the program being watched list/program list • Program list is displayed. Deleting recorded programs Tap a program From the "TV box" screen, tap • Program information is displayed. • "Reservation" X "Record" / "Watch" to Place a check mark to the program reserve recording/watching. to be deleted "Delete" X "Yes" Apps...
Page 131
R eserving Recording/ Note Watching • From the "TV box" screen, X place a check mark in "Select all" X "Delete" X Choose start time/end time and a channel and "Yes" is tapped, all recorded programs reserve a program to record/watch, then follow can be deleted. the settings to start recording/watching. • From the "TV box" screen, X From the Home screen, "Apps" X "Title"/"Date"/"Size" is tapped, the "TV" recorded programs can be rearranged. • Tap on the "TV box" screen to check X "Reservation list" the used space and free space of the X set the settings if necessary internal storage, and the estimate recording time. Reservation The record and watch type presets can be switched. Mode Select a mode to receive data. Available Check the estimate recording recording time. time Channel Select channel.
Page 132
Confi rming/editing reservation Program Enter the program name. name contents Repeat Set a recording/viewing From the "Reservation list" screen, reservation repeatedly at the tap a viewing reservation same time period on a specifi c • Edit reservation contents and tap "Save". day of the week. Deleting reservation contents "Save" From the "Reservation list" screen, Note • If the device is not ON when the preset Place a check mark in "Select all" or time is achieved, recording/viewing the recording/viewing reservation cannot begin, nor can notifi cations of the that you want to delete beginning of programs be given. "Delete" X "Yes" • TV (Full seg/1Seg) recordings can only be saved in the internal storage. Recorded images can only be watched on the device. • Be aware that redundant presetting cannot be done. Apps...
Page 133
U sing TV Link S witching Viewing Area Some data broadcasts may show link From the Home screen, "Apps" X information (TV link) to related sites. By "TV" registering a TV link, it is possible to connect X "Change area" to related sites later. • To register a TV link, tap the item that can be • When adding new area, registered for the TV link that is displayed in Select an area the data broadcast area. • The viewing area changes. • The TV link can only used with 1Seg. From the Home screen, "Apps" X T V (Full seg/1Seg) Settings "TV" From the Home screen, "Apps" X X "TV link" "TV" Tap a TV link X change settings if necessary • Connect to the registered site. Scan Scan the channel and Note obtain the data again.
Page 134
Reservation list Choose a channel TV Brightness Set screen and time and reserve settings brightness. a program to record/ • Place a check watch. mark in "Automatic brightness" so TV link The registered TV link that screen list is displayed. brightness changes Change area Add or change the automatically as watching area. the environment changes. Auto-off Set the time to end TV automatically. Screen size Set screen size. Subtitles Set on/off for Superimpose Set whether to use subtitles. Telop or not. • Subtitle display is The information ...
Page 135
TV CAS While watching Full C amera settings Information seg, the required This terminal has a built-in camera that can device information shoot photos and videos. of this terminal and the received device Before Shooting information based on each channel are All photos and videos shot on your terminal are displayed. saved to the internal storage. • Tap "Reset" to receive the channel C opyrights and portrait rights information again. Avoid copyright infringements when copying Reset Delete data or editing photos and videos that have been broadcast registered with the shot on this terminal. You should also avoid memory data broadcast and infringing the portrait rights of other people by TV links. using or modifying their portraits without their consent. Note that the shooting or recording of ...
Page 136
• Do not expose the lens to direct sunlight for N otes for capturing images a long period of time and do not point at the • Though the camera is manufactured using sun or a bright light directly. The image may extremely accurate technology, some dots become discolored or the camera may fail to and lines may always be displayed to be operate properly. lighter or darker than you expect. Images • Do not cover the lens with your fi ngers or hair shot under very low light intensity contain when shooting. increased noise such as white lines or • Shooting a fast moving object may result in random dots, but it is not a malfunction. an image slightly distorted from the image • This is normal. Clean the lens with a soft displayed on the screen at the time of cloth before shooting. If the lens is stained shooting, or the image may be blurred. with fi ngerprints or oil, the shot photo may • When the battery level is low, you may not be appear out of focus or blurred. able to save shot photos or videos. Check the • Do not leave this terminal in a warm place battery level before using the camera. or under a direct sunlight for a long period of • Shot photos or videos may diff er from the time. The quality of shot photos or video may ...
Page 137
Display/Hide icons V iewing Shooting Screen Display/Hide the icons ( , , , , , ) on the camera screen. This camera can take pictures with both horizontal display and portrait display. The Flash on/off /auto switch meaning of marks (icons, etc.) displayed on the Set fl ash switch. shooting screen are shown below. • Depending on the shooting mode, fl ash may not be able to be set. Switch cameras Switch between the front and main cameras. Shooting mode (setting) Set to Auto/Panorama/Dual. S ettings Set up Dynamic tone (HDR)/Resolution/ Voice shutter/Self-timer/Grid display/Invert left and right part of an image and save/ Saving location/Gesture view. Also you can check Help of the settings. • Depending on the shooting mode, there are items that may not be able to set up. • ...
Page 138
Auto focus frame Cancel auto focus button The frame is white when adjusting focus. It Tap the screen while recording the video to changes to blue when focus is done. display the button. When the icons ( , , , , , ) on the Tap the displayed button to cancel the auto camera screen are not displayed, tap the focus. screen to put the focus on the tapped place Still image button and then take the still image. It is displayed during recording the video. Tap Thumbnail it to capture the moment as a still image. • Tap to select an application to use and Stop recording button confi rm the still image you took. Also you Stop recording the video. can edit the still image (P144). Pause button • Touch and hold to display the quick Stop the recording temporarily. preview screen. Confi rm the still images you took, or drag one to and release S hooting a Photo your fi...
Page 139
S hooting a Video Note • Touch and hold on the still image From the Home screen, "Camera" shooting screen, or press the volume key Point the camera at the subject (up)/volume key (down) for over one second to take still images continuously. • When the shooting mode is "Dual", the main • The recording start sound plays and camera and front camera can take still Camera starts shooting. images at the same time. • When the recording starts, the recording - Drag the small window to move it. elapsed time will be displayed on the - Touch and hold down the small window recording screen. till it turns to aqua color to adjust the • Press the volume key (up)/volume key frame size. (down) while recording to take a still - Tap the small window to switch it to the image of that moment. big window. • You can zoom in/out by pinching out/in the touch screen during video shooting.
Page 140
G allery Note • When the video resolution is set to You can display photos or play back videos "1920x1080 (FHD)"/"1280x720 (HD)"/ stored in the terminal that have been obtained "Slow Motion (120HD)", a video will be by shooting with the camera or downloading recorded with the preview screen being from the Internet. enlarged. The actual recorded screen size is the same as the screen size during Viewing Photos and Videos recording. From the Home screen, "Apps" X "Gallery" Tap an album • Both photos and videos are displayed by thumbnail. • To view photos or videos shot by this terminal, tap "Camera". • In album list, tap to activate camera, then you can take photos or record videos. Tap one of the thumbnails • Display photos and play back videos. • You can zoomed in or zoom out a photo by double-tapping or pinching out or in on the touch screen. Apps...
Page 141
- "Move": Move a photo to another album. Note - "Copy": Copy a photo to another album. • The following operations are available on - "Copy to Clip Tray": Copy a photo to Clip the photos/video list screen. board. - : Launch camera to shoot photos or - "Lock" : Lock a still image. videos. - "Slideshow": Display the saved photos by - : Select a photo or a video to share/ slide show. send. - "Rotate left": Rotate a photo to the left. - : Select a photo or a video to delete. - "Rotate right": Rotate a photo to the • The following operations are available on right.
Page 142
• Since GPS is governed by the United States G PS/Navigation Department of Defense, the GPS signals might be controlled (degradation of accuracy, By using applications that supports GPS signal blackouts, etc.) according to national function on this terminal, you can confi rm security reasons of the US. Also even if the present location or search route to a positioning is done in the same locations destination. and environments, identical results may not be obtained due to the diff erences in signal I n Using GPS conditions caused by the locations of the satellites. • XXX is not liable for any damage caused by • Wireless communication products (mobile failure of GPS system etc. phone or data detector etc.) may intercept • It cannot be used as navigation devices for satellite signal and signal reception may not aircraft, vehicles and people or as a high be stable. precision GPS for measurement. Please note • Depending on the legal system of the that XXX shall not bear responsibility for country and area, the displayed map based damages which are pure economic losses ...
Page 143
and underwater ® High accuracy Uses GPS, Wi-Fi and mobile - Near high-voltage lines (GPS and networks to identify current - Inside of cars and trains networks) location. Although current - In poor weather such as heavy rainfall and location can be detected snow more accurately, the terminal - Inside of bags and boxes consumes much power of - Hindrances (people and things) around this battery. terminal ® Battery saving Uses Wi-Fi and mobile E nabling Location Information (Networks networks to identify current only) location.
Page 144
• In order to calculate the current location Note faster, do not move or cover GPS/sub • It may take up to several minutes to antenna with other objects. determine current locations when the • Select "Device sensors only (GPS only)" GPS functions are used for the fi rst time. to gather the anonymous data while • This terminal is equipped with a GPS using GPS. To transfer data, note that receiver that uses satellite signals to the packet communication fee may calculate current locations. Some GPS occur. service functions use the Internet. • Select "High accuracy (GPS and Data communication fee may occur networks)" or "Battery saving (Networks when transferring data via GPS service only)" to allow the anonymous location functions. data in Google location information • To use a function which requires a GPS service to be gathered. The data may be receiver for positioning of your current gathered even when the application is location, check for an unimpeded view of not activated. the sky. Move to another location if your current location is not determined after a few minutes. Apps...
Page 145
S earching a route U sing Maps Use the "Directions" function of Google Maps You can display present location, search another to search the route by car, by train or on foot. place, or search route by using Google map. From the Home screen, "Google" X • Before getting the current location, set to "Maps" "Enabling Location Information" (P147). • To use Google map, you need to connect X select from (vehicle)/ ® LTE/3G/GPRS network or Wi-Fi , and set (mass transit agency)/ (walk) data communication available to use. • Google Maps does not work for all nations or Enter starting point in "Choose regions. starting point" box* X enter destination in "Choose destination" O pening Maps From the Home screen, "Apps" X • Vehicle: Route is displayed. "Maps"...
Page 146
Tap one of the routes displayed at C lock the bottom screen You can use Alarm, Timer, World clock or • Detailed route is displayed. Stopwatch. • Swipe routes at the bottom screen to left or right to show other routes. From the Home screen, "Apps" X • For vehicle and walk, tap "START "Clock" NAVIGATION" to start navigation. Tap a tab at top of the screen Note • Tapping switches screen of each function. • Any operation during driving should be performed by a passenger. S etting Alarm • If you have logged in Google account, you can choose a starting point or From the Home screen, "Apps" X destination from home, work and history. "Clock" X "Alarms" tab S earching spots in the area Change the settings if necessary You can search stores and facilities in the ...
Page 147
Alarm with Set if vibrate or not while Note vibration alarm is ringing. • The alarm functions at the time set for Alarm sound Set alarm sound. the alarm. Tap "Dismiss" to stop the alarm. is displayed on the status bar Alarm Set alarm volume. when tapping "Snooze". Alarm functions volume again based on the time duration set in ADVANCED SETTINGS "Snooze duration". • On the "Alarm list" screen, X "Select Auto app Set the application to all" or place a check mark in the alarm to starter launch when the alarm is delete X "Delete" X "Yes" to delete alarm. stopped. When there is only one alarm that has Puzzle lock Set if to undo a puzzle to been set, X "Yes". stop alarm. Memo Add memos to alarms that are set. "Save" • The Alarm list screen is displayed and set alarm is added to the list.
Page 148
S etting Timer S etting World Clock You can confi rm the date and time for From the Home screen, "Apps" X registered cities in a list. "Clock" X "Timer" tab From the Home screen, "Apps" X Set Hour/Minute/Second "Clock" X "World clock" tab • X Tap "Settings" to set the following settings. Input a city name in search box X Alarm with Set if vibrate or not while tap a city vibration alarm is ringing. • City name, current time and date of the Alert sound Set alarm sound. selected city are displayed in World clock list screen. Alert volume Set alarm volume. Note "Start" • The timer starts. • Touch and hold down the added city X "Set daylight saving" X tap settings to Note set summer time. is displayed besides the city with summer time set.
Page 149
S etting Stopwatch C alendar This terminal has a calendar for managing From the Home screen, "Apps" X your schedule. If you have a Google account, "Clock" X "Stopwatch" tab synchronize data with Google calendar. "Start" O pening Calendar • The stopwatch starts. Tap "Lap" to count lap times. From the Home screen, "Apps" X • To stop the stopwatch, tap "Stop". "Calendar" • Tap "Resume" to restart the stopwatch, and tap "Reset" to reset it. Apps...
Page 150
Switch QSlide application mode S witching Calendar Display Icon of today Move cursor to today's date (date of icon is From the Home screen, "Apps" X changed). "Calendar" Icon to create new X "Day"/"Week"/"Month"/"Year"/" Create a schedule. Agenda" Menu • Tap "Agenda" to display a list of events. The menu is displayed. Tap each list to display the content. Switch calendar display Change the calender display format to Day/ C reating a Schedule Week/Month/Year/Agenda, display/hide the Japanese holidays or display the schedules From the Home screen, "Apps" X of each account. "Calendar" Switch display Tap date/time X X set each item Tap "<"/">" in Day view/Week view/Month X "Save" view/Year view to display the previous/next day, week, month or year. Note Date of today • When it turns to the time set in "REMINDERS" Selected date screen ...
Page 151
C hanging/Deleting a Schedule Q Memo+ Simply take a memo without activating the From the Home screen, "Apps" X memo application. Write characters or draw "Calendar" illustrations directly on a captured screen. X "Agenda" Open the notifi cation panel (P70) X "QMemo+" Tap a schedule to change/delete X (edit)/ (delete) • From the Home screen, "Apps" X • Tap to edit contents and then "Save". "QMemo+" X "+" to activate it. The tool bar contents are diff erent depending on if • Tap and "Yes". it is activated from the notifi cation panel • On the Calendar screen, tap X "Delete" X "Select all" or place a check mark in or from an application screen. schedules you want to delete X "Delete" Create a memo X "Yes" to delete. ...
Page 152
C alculator From the Home screen, "Apps" X "Calculator" • From the Calculator screen, X "Scientifi c calculator"/"Basic calculator" to change functions. If it is landscape display, both basic calculator and scientifi c calculator are displayed. • Touch and hold the value or formula displayed in formula display fi eld to cut/ copy/paste it or display it on clipboard. • Tap to delete input numbers or operators one by one. • Tap X "Calculation history" to display formula history. When history is displayed, tap X "Yes" to clear all history. • Tap to move to QSlide application Undo/Redo. mode. Edit font, or select a color. Select a pen type and a color. Use an eraser. Display/hide the tool bar. Save the memo you created. Change the paper style of the created ...
Page 153
S ettings S ettings Menu W IRELESS NETWORKS From the Home screen of this terminal, "Apps" Set to enable/disable networks and set the X "Settings" to display the "Settings" screen network connection settings. to set diff erent settings. Wi-Fi (P158) WIRELESS (P157) Bluetooth (P203) NETWORKS Mobile data (P164) DEVICE (P171) Call settings (P95) PERSONAL (P182) More... (P165) SYSTEM (P190) Settings...
Page 154
® W i-Fi Note • Packet communication can be connected, This terminal connects to the Internet via ® even when Wi-Fi function is ON. ® access points for Wi-Fi networks or public ® ® However, while Wi-Fi is available, Wi-Fi wireless LAN services. To connect, you must ® is prioritized. When the Wi-Fi network is confi gure the access point connection settings disconnected, this terminal automatically on this terminal. connects to the LTE/3G/GSM network. ® ■ Reception interference caused by Bluetooth Note that if you keep connecting via the devices LTE/3G/GSM network, you may incur • As wireless LAN (IEEE802.11 b/g/n) and packet communication charges.
Page 155
® C onnecting to a Wi-Fi network Note From the Home screen, "Apps" X • Open network and protected network are two types networks that are available. "Settings" X "Wi-Fi" The network type is indicated by an icon • When "Wi-Fi tutorial" screen is displayed, to the network name. represents tap "Continue" to start a tutorial, or tap an open network and represents a "Close tutorial" to display "Wi-Fi" screen. protected network. The icon also indicates Turn on "Wi-Fi" the signal strength. ® Tap the Wi-Fi network that you Strong signal: Weak signal: want to connect to ® • To search Wi-Fi network again, tap ® • If you try to connect to a protected Wi-Fi "Search" on the "Wi-Fi" screen. network, you will be prompted to enter the • Network name is not displayed depending ®...
Page 156
® A dding a Wi-Fi network • When "Switch to mobile data" has a check mark, if the mobile network icon is From the Home screen, "Apps" X displayed on the status bar, it indicates "Settings" X "Wi-Fi" that the mobile network is being used and note that the packet communication Turn on "Wi-Fi" fee will occur. X "Add Wi-Fi" When the popup screen of switching mobile data is displayed, select "Don't Enter network SSID in the "Wi-Fi show this again" and tap "OK" so that the name (SSID)" box popup screen is not displayed anymore. Tap "Security" box From then on, if the Internet is connected to an unavailable wireless LAN, it • Select the appropriate type from "None", switches to the mobile network and note "WEP", "WPA/WPA2 PSK", and "802.1x that the packet communication fee will EAP". occur. • The setting method diff ers depending on • If the access point which is not being the security settings. connected to the Internet is being "Connect"...
Page 157
Setting mobile data switch Using static IP address ® Set whether to check availability of the You can set the terminal to connect to Wi-Fi ® connected Wi-Fi network and change to the network using the static IP address. mobile network automatically if it is unavailable. From the Home screen, "Apps" X From the Home screen, "Apps" X "Settings" X "Wi-Fi" "Settings" X "Wi-Fi" Turn on "Wi-Fi" Turn on "Wi-Fi" Tap a Wi-Fi ® network to connect X place a check mark in "Show Place a check mark in "Switch to mobile data" advanced options" Tap "IP settings" fi eld X "Static" Note Set required items ® • When the Wi-Fi which is connected to • To use static IP address, enter the an access point that is not connected following items. to the Internet, such as wireless LAN - IP address internal memory card, is disconnected ...
Page 158
® ® Confi rming/Deleting the saved Wi-Fi U sing Wi-Fi Direct network ® Devices support Wi-Fi Direct are connected without using access point. From the Home screen, "Apps" X ■ Asking for connecting with another Wi-Fi "Settings" X "Wi-Fi" ® Direct supported device Turn on "Wi-Fi" From the Home screen, "Apps" X X "Saved Wi-Fi" "Settings" X "Wi-Fi" ® • The Wi-Fi network list that was Turn on "Wi-Fi" connected to is displayed. X "Advanced Wi-Fi" X "Wi-Fi Direct" ® Tap a Wi-Fi network name ® • Tap "Search" when the Wi-Fi Direct • ...
Page 159
® S etting advanced Wi-Fi settings ® Passpoint When Wi-Fi is ON, set to connect to the available From the Home screen, "Apps" X Passpoint supported "Settings" X "Wi-Fi" access point or not. Turn on "Wi-Fi" CONNECTION X "Advanced Wi-Fi" Wi-Fi Direct * (P162) Change the settings in necessary Connect by Connect to WPS (Wi- WPS button* ® Protected Setup) NOTIFICATIONS supported access point. Connect by Wi-Fi You will be automatically WPS PIN* notifi cation* notifi ed when an open PERSONAL network with no security protection is detected. Install Install the network ...
Page 160
Setting mobile data M obile Data From the Home screen, "Apps" X Items such as whether or not use mobile data "Settings" X "Mobile data" X communication, limit mobile data usage, data usage cycle and the services being used are displayed. Restrict Restrict auto mobile background data communication. D isplaying mobile data screen data Mobile data usage (rough number) is ® Show Wi-Fi Set if display Wi-Fi displayed either term by term or application by usage usage or not. application. Mobile Set to disable From the Home screen, "Apps" X ® hotspots specialized Wi-Fi "Settings" X "Mobile data" network on background applications. Note Mobile (P165) • ...
Page 161
M ore... Miracast Set to share screen display and sound on Set other network settings. video equipment that supports Miracast via A irplane mode Turn ON/OFF radio ® Wi-Fi Direct . When wave emitting. available devices Tethering USB (P166) are not found, tap tethering "Search for devices". Wi-Fi (P167) SmartShare Beam (P213) tethering Media server Use DLNA to share Confi gure (P167) the peripheral device Wi-Fi and media contents. hotspot NFC/Osaifu-Keitai (P168) Timeout Set the time ...
Page 162
® Windows 7/Windows Vista devices and Bluetooth compatible devices to * We do not guarantee operations Internet. conducted in environment with E nabling USB tethering upgraded OS or in added/changed environment. Use microUSB Cable 01 (optional) to connect • A driver for USB tethering is required. For this terminal and a PC to access to the details, refer to the following website. Internet by using this terminal as a modem. http://www.lg.com/jp/support/software- Use a microUSB cable to connect manuals (In Japanese only) this terminal and a PC (P211) • You can install the driver through the "Install PC programs" screen displayed From the Home screen, "Apps" X when this terminal is connected to a PC. "Settings" X "More..." X "Tethering" • USB tethering can be used together with ® ® "USB tethering" Wi-Fi tethering and Bluetooth tethering. Settings...
Page 163
■ S etting Wi-Fi access point can access to the Internet simultaneously by From the Home screen, "Apps" X ® using this terminal as a Wi-Fi access point. "Settings" X "More..." X "Tethering" From the Home screen, "Apps" X "Confi gure Wi-Fi hotspot" "Settings" X "More..." X "Tethering" Enter network SSID in "Wi-Fi name "Wi-Fi tethering" (SSID)" box Note Tap "Security" box ® • Wi-Fi tethering can be used together • Select an appropriate one from "Open", ® with USB tethering and Bluetooth "WPA PSK" and "WPA2 PSK". tethering. • A password is necessary when setting to "WPA PSK" or "WPA2 PSK". "Save" Note • At the time of purchase, network SSID is set to "KS1604̲xxxx", and security is set to "WPA2 PSK". Set security settings if necessary. Settings...
Page 164
® E nabling Bluetooth tethering S etting NFC/Osaifu-Keitai ® Up to fi ve Bluetooth devices can access Set and manage NFC/Osaifu-Keitai settings. to the Internet simultaneously by using this From the Home screen, "Apps" terminal as a modem. X "Settings" X "More..." X "NFC/ From the Home screen, "Apps" X Osaifu-Keitai settings" "Settings" X "More..." X "Tethering" "Bluetooth tethering" NFC/Osaifu- Restrict Osaifu-Keitai Keitai lock functions and its usage services. Note Reader/ Turn ON/OFF NFC • Pairing with this terminal is required to ® Writer, P2P reader/writer and P2P use Bluetooth . functions. For details, refer to "Pairing/Connecting ®...
Page 165
C onnecting to VPN C onnecting to VPN (Virtual Private Network) From the Home screen, "Apps" X "Settings" X "More..." X "VPN" VPN (Virtual Private Network) is a technique to access to the information protected in local Tap a VPN name to connect to network from other networks. VPN is generally Enter the required authentication equipped in companies, schools or other information X "Connect" facilities. Users can access the local network and view information outside the premise. E diting VPN To set VPN access from this terminal, security information from network administrator is From the Home screen, "Apps" X required. "Settings" X "More..." X "VPN" A dding VPN Touch and hold down a VPN name to edit From the Home screen, "Apps" X "Settings" X "More..." X "VPN" "Edit" X Add, delete or edit the • If an attention screen appears, tap information X "Save"...
Page 166
A lways use VPN S etting an additional access point 〈New APN〉 From the Home screen, "Apps" X "Settings" X "More..." X "VPN" From the Home screen, "Apps" X "Settings" X "More..." X "Mobile X "Always-on VPS" networks" X "Access Point Names" Select a VPN profi le X "OK" X "New APN" "Name" X enter the network profi le S etting Access Point name you want to create X "OK" Access point for connecting the Internet (sp- "APN" X enter the access point mode) is already registered. You can add or name X "OK" change it if necessary. For details about sp-mode, refer to website. Enter other items required by the When using mopera U or Business mopera network operator Internet, add access point manually. For details on mopera U, refer to mopera U X "Save" website. Note C hecking the access point in use • ...
Page 167
I nitializing access point D EVICE When initializing an access point, it returns to the default settings. S ound From the Home screen, "Apps" X "Settings" X "More..." X "Mobile Set sound settings such as phone ringtone, volumes and vibrate. networks" X "Access Point Names" X "Reset to default" X "Yes" BASIC M anner Mode Select from "Sound & Vibrate", "Vibrate only" or "Do not disturb". V olume Set the volumes for "Ringtone", "Notifi cation sound", "Touch feedback & system", and "Music, video, games & other media". RINGTONES & VIBRATIONS Ringtone Set a phone ringtone. Notifi cation Set up a notifi...
Page 168
NOTIFICATIONS Voice Set whether to read out the notifi cations sender's information and Do not Set whether to ring when the message contents of disturb there is an important a received message (SMS) notifi cation such as an automatically. incoming call, a new • In "Voice notifi cations message. language", set preferred • The alarm always rings. engine, speech rate and Lock screen Set whether to display listen to an example. contents (contents of a received mail, etc.) or notifi cations when the screen is locked. Apps Allow/block the notifi cations from each application. ADVANCED SETTINGS Vibrate on Set whether to vibrate when tapping any home touch button or dialpad (P54).
Page 169
D isplay FONT Font type Set the font displayed on the Set display settings such as screen brightness screen. or animations. Font size Select from "Minimum", SCREEN "Small", "Medium", "Large", B rightness Set screen brightness. "Very large", "Maximum". • If you place a check mark in ADVANCED SETTINGS "Automatic brightness", the screen brightness changes Smart screen Set if screen stays on when automatically according to you are watching the screen. the environment. Home touch Select a layout and a color S creen Set time duration before buttons for home touch buttons, or timeout screen turns off automatically. set whether to display the ...
Page 170
H ome Screen D isney Character Settings Set the Home screen settings. Select a Disney character to change the window image, live wallpaper, ring tone, etc. Select Home Switch home applications. of the mickey window cover collectively or individually. SCREEN • To use it, you need to download/update Wallpaper Set a wallpaper. "Disney マーケット (Disney Market)" application, and set up an Google account Screen swipe Select a screen eff ect. (P119, P187). eff ect Allow Home Set to go to the initial screen Collective settings screen or not when scrolling the From the Home screen, "Apps" X looping Home screen. "Settings" X "Disney character DATA settings" Home Back up or restore the ...
Page 171
I ndividual settings L ock Screen From the Home screen, "Apps" X Set to lock screen or not. Set settings if "Settings" X "Disney character necessary. • The display and setting items vary depending settings" on your selection from "None", "Touch", Tap a Disney character X swipe "Swipe", "Knock Code", "Pattern", "PIN", the screen to left/right to display "Password" to unlock the screen. the items to be changed X " 個別設定 SCREEN SECURITY (Individual settings)" X "OK" • The settings of the selected items are Select None Disable the security of screen unlocking screen. changed. lock Touch Tap to unlock screen. Swipe Swipe to unlock screen. Knock Tap the pattern that you Code set when the screen is OFF to unlock it.
Page 172
Select Password Enter a password to Randomize PIN Set whether the number screen unlock screen. Follow the entry layout on keyboard is lock on-screen instructions random when inputting PIN. to enter a 4 to 16-digit Hidden Set whether to display the password including password password input area when alphabets. tapping the screen. Smart Lock Set to unlock the touch CUSTOMIZE screen automatically by a Wallpaper Set wallpaper when locking trusted terminal, location or face that you have set up. screen. Shortcuts Customize the shortcut Screen swipe Set the screen eff ect when displayed on the lock eff ect swiping the screen to unlock. screen. Pattern eff...
Page 173
• If you entered an incorrect password for LOCK TIME fi ve times, a message is displayed to L ock timer Set time duration from the remind you to re-input the password after screen turns off till it is 30 seconds. If you forget the password, locked. tap "Forgot password?" on the reentry screen and log in with your Google Power button Set to lock the screen account set up on your terminal to unlock instantly locks immediately or not after screen. pressing the power key. • Note that you cannot unlock the screen if you forgot the PIN or the password when Note Google account has not set up yet. <Lock screen notifi cation> 〈On-Screen Unlock〉 • When the screen lock is set to "Knock • If you entered an incorrect screen-unlock Code"/"Pattern"/"PIN"/"Password", a patterns for fi ve times, a message is screen appears so that you can select displayed to remind you to re-input the pattern after 30 seconds. If you forgot ...
Page 174
G estures SENSOR Motion Calibrate the accuracy of Enable or disable each gesture. sensor sensor (the tilt and speed of ANSWER ME calibration the sensor). • Operate it when Gesture does Silence When this terminal is ringing not work properly. incoming or vibrating, fl ip the terminal calls over to make the display face * Operate only when the Home selection is downwards to stop ringtone or "Home". vibration. OTHERS Snooze or Flip the terminal over to make stop alarm the display face downwards to stop alarm. • Snooze function works if you have set "Snooze duration" to "Off " in Alarm/Clock application. Cinderella ...
Page 175
S torage B attery Display free space in internal storage and Confi rm the remaining battery, set to restrict microSD card, operate mount and format. the usage of each function when the battery is getting less. INTERNAL STORAGE BATTERY INFORMATION Total space Total space of the internal storage is displayed. Remaining Battery levels are battery icon displayed in percentages. Available Available space of the internal It displays whether the storage is displayed. battery is being charged, Apps, Used space of the internal the expected time to Audio etc. storage is displayed. charge fully/the usable total time. SD CARD Battery usage Confi rm the details of Total space Total space of the microSD ...
Page 176
T urn on battery saver A pps When the remaining battery is less than the Manage or delete the installed applications. set value, etc. set the battery saver to restrict the battery consumption by reducing the Confi rming downloaded application/ screen brightness, etc. all applications • Confi rm the description related to battery saver in Help. From the Home screen, "Apps" X "Settings" X "Apps" X tap an From the Home screen, "Apps" X application in "DOWNLOADED" "Settings" X "Battery" X "Battery tab/"ALL" tab/"DISABLED"tab saver" Turn on "Battery saver" Force stop Force-quit an application being activated. "Immediately"/"5% battery"/"15% battery" Disable/ Disable/enable Enable/ application or uninstall Uninstall application. Show Set if show notifi cation notifi...
Page 177
Deleting an application D isabling an application • Some preinstalled applications may not be Disabled application stops its operation and it able to be deleted (uninstalled). Part of the is not displayed on the Apps screen. applications can be disabled (P181). • It will not be uninstalled. • It is recommended that the applications • It is available for some applications or purchased from Play Store be delete (P122) services that cannot be uninstalled. from Google Play screen. From the Home screen, "Apps" X From the Home screen, "Apps" X "Settings" X "Apps" X "ALL" tab "Settings" X "Apps" X "ALL" tab Tap an application to disable Tap an application to delete "Disable" X "Yes" "Uninstall" X "OK" Note • When an application is disabled, the linked applications may not run properly. In such case, enable it again to run properly. Settings...
Page 178
E nable an application again L ocation From the Home screen, "Apps" X Set GPS settings, etc. "Settings" X "Apps" X "DISABLED" Mode (P147) RECENT LOCATION REQUEST Tap the application you want to enable again When there are applications that request the latest location information, the list is displayed. "Enable" LOCATION SERVICES D efault Message App Camera Set whether to record the location information in the Select a message application which is used photos or videos taken by the normally from "messaging" and "Hangouts". camera. From the Home screen, "Apps" X Google Set whether to use Google "Settings" X "Default message app" Location location information service "Messaging"/"Hangouts" Reporting so that the application can get the user location quicker. Gather the anonymous location information and send ...
Page 179
S ecurity PASSWORDS Password Set if show the last character Set password settings. typing of a hidden password or not as Content Select a lock type when locking visible you type. lock a fi le in gallery. PHONE ADMINISTRATION ENCRYPTION Phone Select a device administrator Encrypt Encrypt the system data saved administrators to activate in this terminal. phone in the internal storage. After Unknown Set if allow installation of that, PIN or password is required sources applications from sources other every time when the power is than Google Play. turned on to decode. • To cancel the encryption, Verify apps Disallow or warn before from the Home screen "Apps" installation of applications that ...
Page 180
S ecurity code on this terminal Clear Delete credential information credentials of all contents and VPN in Some functions provided for convenient use of credential storage. the terminal require the security code to use • To delete an installed them. Besides a password for screen lock of the certifi cate, you need to terminal, a network security code necessary delete credential storage. for the network services etc. are available. Make use of the terminal using an appropriate ADVANCED SETTINGS security code according to the purpose. Trust Set whether to execute the • Entered PIN/password for screen lock, agents selected operation when a network security code, PIN code and PUK trusted terminal is connected. code are shown as "•". ■ Cautions on using security codes Screen pin Set whether to fi x a certain application on the screen of • Avoid using a number that is easy to this terminal or not.
Page 181
• The PUK code is written on the ■ P IN code subscription form (copy for customer) The nano UIM card can set security code handed at the subscription in the Shop. If named PIN code. This code is set to "0000" you have subscribed at other than Shop, at the time of subscription, but you can you should bring your offi cial identifi cation subsequently change it. (such as driver's license), the nano UIM PIN is a 4- to 8-digit number (code) that card with you to the nearest Shop or must be entered for user confi rmation to contact "Information Center" on the last prevent unauthorized use of nano UIM card page of this manual. by a third party every time you insert the nano UIM card into the terminal or when the ■ PIN/password for screen lock terminal is powered on. You can set entering The security code is used for lock function of the PIN code enables making/receiving calls the terminal. and terminal operations. ■ N etwork security code ...
Page 182
■ P IN unblocking key (PUK) C hanging PIN The PIN unblocking key is an 8-digit number Enable PIN beforehand. used to unblock the PIN code. You cannot From the Home screen, "Apps" X change it by yourself. • If you enter the PIN unblocking key "Settings" X "Security" incorrectly ten times in a row, the nano UIM "Set up SIM card lock" card will be locked. If this happens, please contact a Shop. "Change SIM PIN" Enter the current PIN, and tap "OK" S etting PIN code Enter a new PIN and tap "OK" You can set to require the PIN code entry for using the terminal when the power is turned Enter the same PIN that you entered in step 5 and tap "OK" From the Home screen, "Apps" X "Settings" X "Security" "Set up SIM card lock" "Lock SIM card" Enter PIN and tap "OK" • Place a check mark in "Lock SIM card". Settings...
Page 183
E ntering PIN A ccounts & sync Follow the operations below if you are asked to Add or delete an account used in this terminal, enter the PIN when turning on this terminal. such as Google account. Set synchronization Enter the PIN of the nano UIM card, settings. and tap "OK" S etting account U nlocking PIN From the Home screen, "Apps" X "Settings" X "Accounts & sync" Follow the operations below to unlock PIN when you have entered PIN incorrectly for 3 "Add account" times in a row. Tap an account type you want to add From the PUK input screen, enter PUK code and tap "OK" Set according to the on-screen instructions Enter a new PIN and tap "OK" Note Enter the same PIN as you entered in step 2 and tap "OK" • The application automatically synchronizes data if "Auto-sync data" is turned on. Packet communication fee may be charged ...
Page 184
"Settings" X "Accounts & sync" terminal. You can also set voice input and output settings. Tap an account type to delete Language Select a language you use in Tap the account name to delete this terminal. X "Remove account" X "OK" KEYBOARD & INPUT METHODS Default Select default keyboard and input method. Google voice Tap to place a check mark typing to use. Also tap to set the settings. LG Japanese Tap to set settings keyboard (P62). Moji-Henshu Tap to confi rm the application information and open source license information. SPEECH Voice Search Set up a language to use in voice recognition. Text-to- Set speech settings. You can speech set preferred engine, speech output rate and listen to an example.
Page 185
I nitializing this terminal MOUSE/TRACKPAD Pointer Set pointer speed when this From the Home screen, "Apps" speed terminal is connected a with "Settings" X "Backup & reset" mouse or a trackpad. "Factory data reset" X "Reset phone" X "Delete all" X "OK" B ackup & reset • When deleting the data saved in microSD card, place a check mark in "Erase SD Initialize settings. card". BACKUP & RESTORE Note Backup my Set to backup on the Google • The battery level should be more than data server or not. 30% for initializing this terminal. Backup Set an account for backup. • Backup your data such as images, account Add an account to use as a videos and music on PC. For details backup in "Add account". about connection method, refer to "File ...
Page 186
S YSTEM Set time Set time manually. • Set up the settings after Set shortcut keys, date and time, accessibility, turn off "Auto-date & time". mickey window cover, print and terminal Select time Set time zone manually. information. zone • Set up the settings after turn off "Auto-time zone". S hortcut Key Use 24-hour Set to display the time in 24- Set whether to quickly access to QMemo+ or format hour or 12-hour format. camera when the screen is turned off or when Select date Set the date format. pressing and holding the volume key on the format lock screen. D ate & time Set settings about date and time. ...
Page 187
A ccessibility Voice Set whether to read out the notifi cations sender's information and Set application settings related to the message contents of accessibility. a received message (SMS) automatically. VISION • Set preferred engine, adjust TalkBack Enable user assistance speech rate and listen to services such as responding an example demonstration to user operations via audio in "Voice notifi cations and vibrations, reading out language". text . Also set settings of Screen shade Set the brightness to the speech, other feedback, minimum to save battery. touch exploration, etc. Accessibility Set whether to enable the Font size Select from "Minimum", shortcut start of accessibility function "Small", "Medium", "Large", from each of the screens.
Page 188
Notifi cation Set to turning on the LED RECOGNITION light during an incoming call Touch Set the screen area where or a notifi cation. control the touch operation is not Flash Set the camera fl ash to blink areas allowed. alerts during an incoming call or a SYSTEM notifi cation. Auto-rotate Automatically switch the Turn off all Set whether to turn off all the screen screen to portrait display/ sounds sounds. landscape display when this Captions Customize the subtitle terminal is rotated. settings for hard-of-hearing Password Use TalkBack to read the people. voice input password out loud.
Page 189
Accessibility Triple-tap the home key to Note settings toggle "TalkBack", "Invert colors" • You can download and set applications shortcut and "Touch assistant". You compatible with user assistance services can also jump to "Accessibility from Google Play. settings". When you choose • If you authorize the usage of TalkBack, be "Show all", you can select careful since personal information such functions to set at any time. as credit card numbers, etc. might also be recorded in exchanges via user interfaces. SERVICES If perchance, data and information which Switch The operations when were registered happen to be leaked, Access the back key, or home please be forewarned that XXX shall not key, etc. is pressed set bear any responsibility. whether controlling is to be • If TalkBack is allowed to use, the Touch substituted by physical key guide function also becomes valid. The combinations such as the Touch guide is a function which can read power key, etc. aloud and display explanations of the items where your fi nger is positioned. After you once turn on the Touch guide functions, tap ...
Page 190
M ickey Window Cover A uto- When the screen lock is set to unlock "Touch" or "Swipe", the screen Set up the Mickey Window Cover L01 which is lock is canceled automatically in the package. when the fl ip section is opened. Select apps Select applications used on the Help Help is displayed. Mickey Window Cover L01. Preview When a mail (Email) or a P rinting emails & message is received, set messages whether to display the Set or manage the printer which uses Google notifi cation on the mickey cloud print. window cover screen. From the Home screen, "Apps" X • When the screen lock is set "Settings" X "Printing" X "Cloud to "Knock Code"/"Pattern"/ Print" "PIN"/"Password", the check ...
Page 191
Software info Android version, baseband version, kernel Update App (P245) version, build number and Center Updates software version being Software (P240) used in this terminal are Update displayed. Network Network, mobile network Legal info Legal documents for LG type, service state, software, open source roaming, mobile network license, Google legal are state and IP address are displayed. displayed. Status Your phone number and Checking your own phone number IMEI are displayed. From the Home screen, "Apps" Battery The battery status, X "Settings" X "About phone" X remaining power and "Status" the usage state are • Your phone number is displayed in "My ...
Page 193
F ile Management Download Save data downloaded by the Storage Structure browser. Movies Save video data. This Terminal (Internal Music Save music data. Storage) Notifi cations Saves music data etc. to be set as notifi cation sound. Main created folders in the phone (internal storage) at the time of purchase are as Pictures The still image data is saved. follows. Podcasts Podcast data is saved. • Depending on operations on the terminal, Preload The data saved beforehand displayed folders may diff er. after purchasing is saved. Alarms Save music data etc. for Ringtones Save music data etc. for alarm sound. ringtone or alarm sound. Android Save setting data or ...
Page 194
• The UHS speed class of microSD card m icroSD card (External supported by this terminal is class 1. Storage) • The speed class of microSD card supported by this terminal is up to class 10. You can attach microSD card (including microSDHC card and microSDXC card) to the I nserting microSD card terminal and use it. • This terminal supports a microSD card of up Detach the back cover (P36) to 2 GB, a microSDHC card of up to 32 GB, Remove the battery pack (P47) and a microSDXC card of up to 128 GB (as of May 2015). With the metal contacts facing • A microSDXC card can only be used with down, insert the microSD card SDXC compatible devices. Do not insert a into the microSD card slot in the microSDXC card into a device incompatible direction of arrow mark until it is with SDXC since it may cause damage to the fi xed data stored in the microSDXC card. • To use microSDXC card again with damaged data inside, you need to initialize the microSDXC card with an SDXC compatible ...
Page 195
R emoving microSD card F ormatting microSD card When removing the microSD card, make sure Note that formatting microSD card erases all to unlock the SD card mount (safely remove) data in the microSD card. before removing it (P179). From the Home screen, "Apps" X Detach the back cover (P36) "Settings" X "Storage" Remove the battery pack (P47) "Erase SD card" X "Erase SD card" X "Erase everything" Pull microSD card straight out in • When the unlock screen appears, perform direction of arrow mark unlocking method and then tap "Erase everything". File Management...
Page 196
Cloud storage F ile Operations From the Home screen, "Apps" X "File Manager" F ile or Folder Operations "Dropbox" Use "File Manager" to display or manage the • To use Dropbox, you need to have a data, such as the still images, videos, music or Dropbox account. Follow the on-screen documents, which were saved in this terminal instructions. or in cloud storage. Creating a folder S torage in this terminal From the Home screen, "Apps" X From the Home screen, "Apps" X "File Manager" "File Manager" "All fi les" X "Internal storage"/"SD "All fi les"/"Music"/"Image"/"Video"/ card" X tap the folder if necessary "Document" X enter a folder name X "Save" Tap a folder or fi le When the application selection Note screen is displayed, select an • A folder can only be created in "Internal application to use X "OK"...
Page 197
Renaming a fi le or folder D eleting a fi le or folder From the Home screen, "Apps" X From the Home screen, "Apps" X "File Manager" "File Manager" "All fi les"/"Music"/"Image"/"Video"/ "All fi les"/"Music"/"Image"/"Video"/ "Document" X tap a folder if "Document" X tap a folder if necessary necessary Touch and hold a folder/fi le X Touch and hold a folder/fi le X "Rename" X Enter a name X "Save" "Delete" X "Yes" Note Note • When purchasing, some folders such as • When purchasing, some folders such as "Android" or "DCIM" which were created in "Android" or "DCIM" which were created in this main unit (internal storage) cannot this main unit (internal storage) cannot be moved or copied. be moved or copied. File Management...
Page 198
Moving/Copying a fi le or folder Searching Data From the Home screen, "Apps" X From the Home screen, "Apps" X "File Manager" "File Manager" "All fi les" X tap the folder if "All fi les"/"Music"/"Image"/"Video"/ necessary "Document" Touch and hold a folder/fi le X X enter keyword(s) you want to "Move"/"Copy" search Display the moving destination/copy destination folder X "OK" Note • When purchasing, some folders such as "Android" or "DCIM" which were created in this main unit (internal storage) cannot be moved or copied. File Management...
Page 199
Data Communication concrete between them, they may be ® B luetooth Communication unable to connect with each other. Note the above mentioned distance is not ® Connect this terminal to Bluetooth devices guaranteed. wirelessly, to exchange data. • Make sure to keep this terminal 2 m or ® • For Bluetooth compatible version or profi le, more away from another device such as refer to "Main Specifi cations" (P246). home electric appliances, AV devices, ® • For Bluetooth setting and operation OA devices, etc. Microwave oven can procedure, refer to the manual of the ® easily aff ect Bluetooth function, so keep ® Bluetooth devices being connected. this terminal 3 m or more away from • ...
Page 200
• Wireless connection is available when ■ Reception interference caused by wireless ® Bluetooth device is put in a bag or pocket. LAN devices ® However, lowering of communication • As this terminal's Bluetooth device speed or noise may result when you are in and wireless LAN devices use the same ® between the Bluetooth device and this frequency (2.4 GHz), reception interference terminal. may occur or the communications speed ® ® • The radio wave from Bluetooth may aff ect may lower if you use the Bluetooth device the operation of medical electronics etc. near the wireless LAN devices. Also, you ® Bluetooth communication in some cases may hear noise or have a connection may result in an accident, so turn off this problem. In these cases, do the following: ® ®...
Page 201
® Turning ON Bluetooth P airing/Connecting with ® Function to Make this Other Bluetooth Device Terminal Discoverable ® To transfer data by Bluetooth communication, perform pairing (pairing setting) with another From the Home screen, "Apps" X device in advance, and then register it to this "Settings" X "Bluetooth" terminal. ® • Depending on Bluetooth devices, there are Turn on "Bluetooth" devices with only pairing and those conduct till connection. Note From the Home screen, "Apps" X ® • When you do not use Bluetooth function, "Settings" X "Bluetooth" turn it off to save the battery. ® • The setting of the Bluetooth ON/OFF is not Turn on "Bluetooth" changed even when the power is turned off...
Page 202
When answering pairing request from Note another device • Even for devices requiring pass code When a screen asking for pairing when (PIN) when pairing, once pairing is ® performed, it is not necessary to enter connecting Bluetooth communication is the pass code (PIN) to reconnect after displayed, tap "Pair" or enter pass code (PIN) if required, then tap "OK". disconnected as long as the paring is not canceled. Disconnecting • You can set pairing even if it is a device unable to connect such as an Tap the device you want to incompatible profi le. However, it cannot disconnect from "PAIRED DEVICES" be connected even if you tap the device. list X "OK" • Tap on the paired device X "Connection access" to select whether to Canceling pairing always confi rm automatic connection or not. Tap beside the device that you • Devices that are not compatible with want to unpair from the "PAIRED SCMS-T cannot play data such as music DEVICES" list X "Unpair"...
Page 203
® R eceiving data via Bluetooth Sending/Receiving Data via function ® Bluetooth Function Pair/connect (P205) this terminal ® • Turn on Bluetooth function beforehand to with another Bluetooth ® device make this terminal detectable. The data is sent from the other ® Sending data via Bluetooth function ® Bluetooth device You can send data of phonebook (name card data ® Tap "Accept" when Bluetooth in vcf format), fi les such as photos or videos, etc. ® authorization request screen is to another Bluetooth device (PC etc.). • For sending, perform the operation from displayed on this terminal the menu such as "Share"/"Send" of each • ...
Page 204
A ndroid Beam N FC Communication You can transmit and receive data with a NFC is short for Near Field Communication. device equipped with Reader/Writer, P2P It is an international standard proximity functions. wireless communication system determined • Enable the Reader/Writer, P2P function and by ISO (International Organization for place a check mark in "Android Beam". Standardization). This terminal enables non- • If NFC/Osaifu-Keitai is set to lock, Android contact IC card function, Reader/writer beam cannot be used. function, P2P function, etc. • Depending on the application, Android beam Use NFC function to transfer data with other may not be used. compatible devices. • We do not guarantee any communication with • For holding over the other device, see P124. a terminal equipped with Reader/Writer, P2P functions. • If terms of use screen is displayed when sending or receiving data, confi rm the contents and follow the on-screen instructions. Data Communication...
Page 205
Transmitting data Sending data Transmit fi les of browser webpages, contacts, Enable the Android beam function on images and video to other NFC compatible the receiving end terminal terminals. Enable the Reader/Writer, P2P Example: To transmit images from Gallery function on this terminal and place Enable the Android beam function on a check mark in "Android Beam" the receiving end terminal (P168) Enable the Reader/Writer, P2P A lign the mark on this terminal function on this terminal and place and the transmitting end terminal, a check mark in "Android Beam" and bring them close together (P168) • The beam receiving starts. • is displayed in the status bar. From the Home screen, "Apps" • Reception status can be confi rmed via X "Gallery" X select an image to the notifi cation panel. transmit • After reception ends, a message is A lign the mark on this terminal ...
Page 206
* We do not guarantee operations • To recognize this terminal on your PC, a conducted in environment with dedicated driver and Windows Media Player upgraded OS or in added/changed 11 or later are required. environment. - For details about how to download and • Use a PC to back up the client's data operate the dedicated driver, refer to the saved in the internal storage of this homepage below. terminal and microSD card. http://www.lg.com/jp/support/software- • The data saved in the internal storage of manuals (In Japanese only) this terminal or microSD card from other - Y ou can download the latest Windows devices such as PCs may not be able to Media Player on Microsoft website. display on this terminal. Also, the data http://windows.microsoft.com/en-us/ saved in the PC from this terminal may windows/download-windows-media-player not be able to display on other devices. • Some functions such as shooting and playing a video may not work while this terminal is being connected with a PC. ...
Page 207
C onnecting this Terminal with a PC U sing as Media Device Connect this terminal and a PC with microUSB Insert the microUSB plug of microUSB Cable 01 (optional). This terminal is recognized Cable 01 (optional) in the microUSB as a media device (MTP) and you can transfer connection terminal of this terminal media fi les such as images, music or videos. • Insert the microUSB plug horizontally with C onnect this terminal to PC via USB mark facing up. microUSB Cable 01 (P211) Open the Notifi cation panel X Confi rm "Media device (MTP)" is displayed • When "Send images (PTP)" is displayed, "Send images (PTP)" X "Media device (MTP)". • If the "Install PC programs" screen is displayed on this terminal, tap "Cancel". Operate the PC to transfer data I nsert the USB plug of microUSB between the terminal and the PC Cable 01 in the USB port on PC • This terminal is recognized automatically on a PC.
Page 208
Using as Camera Device C onnecting with Printer Connect this terminal and a PC with microUSB You can print browser images or pictures with cable 01 (optional) and turn to Send images ® a Wi-Fi supported printer. (PTP) mode. You can transfer still images and ® • For operation method about Wi-Fi supported videos to the PC. printer, check the instruction manual. • Use the Send images (PTP) mode to transfer • This terminal and the printer need to be the data to the PCs which do not support ® connected with either the same Wi-Fi MTP. ® network or the same Wi-Fi Direct • The following fi le formats are compatible to a Connect this terminal to PC via ® Wi-Fi supported printer. microUSB cable 01 (P211) ■ File formats available to print out ...
Page 209
C onnecting with Other Timeout When SmartShare Beam is not being used, set the Devices time duration before it turns off automatically. U sing SmartShare Beam File Display the list of all the transfer fi les which were sent/ Use SmartShare Beam to send or receive history received by SmartShare contents. Beam. S etting SmartShare Beam Help Display Help. Set to publish the contents on this terminal on other client devices. From the Home screen, "Apps" X "Settings" X "More..." X "SmartShare Beam" Turn on "SmartShare Beam" (Device Change the name of this name) terminal which is displayed on another device. Storage Set a destination to save ...
Page 210
S ending fi les to client device via R eceiving fi les to client device via SmartShare Beam SmartShare Beam You can send contents in this terminal to other You can receive contents from other client client devices. devices. Example: Sending pictures from Gallery When "File transfer" screen is From the Home screen, "Apps" X displayed, "Yes"/"Accept" "Gallery" • is displayed on the status bar. Data reception starts. Select a picture you want to send • You can confi rm the reception condition X "SmartShare Beam" from notifi cation panel. • When data is received, a message screen Tap a device to send the picture is displayed at the bottom of the screen. ® • When it is sent by Wi-Fi Direct , turn on the SmartShare Beam on the client receiving device in advance. ® • ...
Page 211
Connecting with TV Note <Usage of SlimPort supported cable or You can connect this terminal with a TV to display videos and pictures. SlimPort supported accessory> • To connect this terminal with a TV, use a • Video or audio may not be output properly when connecting with a TV which does commercially available SlimPort supported not support HDCP. Depending on the cable or SlimPort supported accessory. contents, some may not allowed to output • HDMI terminal, HDTV terminal, VGA terminal from the content provider, some may be or DisplayPort terminal is necessary on the TV being connected with. checked on due to the functional issues. • Depending on TV, the required SlimPort • When starting outputting, images may not be displayed properly due to output supported cable or SlimPort supported mode switch problem depending on the accessory may diff er. TV being connected with. In that case, • We do not guarantee any operations with SlimPort supported cables and SlimPort switch input mode by TV remote. supported accessories. • Depending on the TV being connected with, data output from this terminal may • Connect from TV side in order. not be able to show full size. Change the ...
Page 212
® ® Disconnecting Wi-Fi Miracast D isplaying on Wi-Fi Miracast supported device ® Supported Device via Wi-Fi Connection Tap a device to disconnect X "OK" ® Connect this terminal and a Wi-Fi Miracast Note ® supported device via Wi-Fi connection to show • Video or audio may not be output properly videos and pictures on TV or on a display. ® when connecting with a device that does • Turn on Wi-Fi function beforehand. not support HDCP. Depending on the From the Home screen, "Apps" X contents, some may not be allowed to "Settings" X "More..." X "Miracast" output from the content provider, some Turn on "Miracast" may be checked on due to the functional issues. ® • Tap "Search for devices" if the Wi-Fi ...
Page 213
U sing Overseas O verview of International Note Roaming • For country codes/international call access codes/universal number The international roaming service allows you international prefi x, supported countries/ to use your terminal in the service areas of areas and network operators, refer to overseas operators affi liated with XXX, with website. the same phone number and email address. Calls and SMS can be used without changing settings. ● Available network This terminal is placed in class 5. You can use it in LTE network, 3G network and GSM/ GPRS network service areas. It can also be used in countries/regions supporting 3G 850MHz/GSM 850MHz networks. Please check the information about the available areas. Using Overseas...
Page 214
A vailable Service Before Using Overseas Overseas C onfi rming before Departure Main GSM Before using this terminal overseas, check the communication 3G850 (GPRS) following information in Japan. service ● C ontract × * Calls ○ ○ ○ • Check whether you have applied for WORLD WING. For more details, contact ○ ○ ○ ○ "General Inquiries" on the back cover of this Email * ○ ○ ○...
Page 215
P re-confi guring Settings for Using Overseas ● Network service confi guration S etting data roaming If you have subscribed Network service, voice mail service, call forwarding service, To perform packet communication overseas, number notifi cation service, etc. are available you need to turn on data roaming. overseas. However, some network services From the Home screen, "Apps" X are unavailable. "Settings" X "More..." X "Mobile • Starting "Remote operation settings" networks" service is required when using networks "Data roaming" X confi rm notes service overseas. You also can set "Remote operation settings" after arriving abroad. screen and tap OK - From Japan (P96) S etting a network operator ...
Page 216
S etting network mode Inquiries • If your terminal or nano UIM card is lost or From the Home screen, "Apps", X stolen overseas, contact XXX immediately "Settings" X "More…" X "Mobile from your current location and carry out the networks" X "Preferred network procedure to suspend usage. For contact type" information, refer to the back cover of this manual. Please note that you are liable for "LTE/3G/GSM(Auto)"/"LTE/3G"/ any call or communication charges incurred "3G/GSM"/"3G"/"GSM" after the loss or theft of this terminal. • You will need the country's "international About date & time call access code" or "universal number If you place a check mark in "Auto-date & time" international prefi x" if calling from a land-line and "Auto-time zone" in "Date & time", the time phone overseas. and time zone of this terminal's clock will be automatically changed when information about the local time and time zone is received from the network of the overseas operator to which you are connected. • The automatic time/time zone setting may not work properly depending on the overseas operator. In that case, set the time zone manually. • ...
Page 217
X "Call to <country How to Make and Receive name>"/"Call without int'l prefi x" Calls at Your Location • The country name set in "Country code" of "International dial assist" is displayed in the above <country name>. For example, M aking Calls to Other in case of "Japan" (+81), "Call to Japan" Countries (including Japan) is displayed. Tap "End call" to end the call You can use the international roaming service to make calls to other countries while Note overseas. • For information of available countries or • When placing a check mark in "Automatic network operators, see website. conversion function" of "International dial From the Home screen, "Phone" X assist", enter a number starts from area "Dial" tab code the same as when you call in Japan X X tap "Converted number". Enter "+" (touch and hold down "0" ) X country code X area code X other party's phone number in order • If the area code begins with "0", remove the fi rst "0" when entering the number. However, "0" may be required in some countries and regions such as Italy.
Page 218
M aking a Call Domestically M aking a Call to WORLD WING Users You can make a call to the other party's land- line phone or a mobile phone in the same way When the other party that you are making a as in Japan. call to is a WORLD WING user, make a call as From the Home screen, "Phone" X if you are making an international call to Japan "Dial" tab even if the other party is in the country in which you are staying. Enter the other party's phone • Dial "+" and "81" (country code of Japan) number fi rst and then dial the phone number omitting • To make a call to a land-line phone, enter the "0" at the beginning as if you are making the area code and the other party's phone a call to Japan because the call is routed number. through Japan regardless of the destination. Tap "End call" to end the call Using Overseas...
Page 219
R eceiving Calls Overseas M aking a Call from Other Parties You can receive calls in the same way as in Japan. ● Having the other party call you overseas from Japan Note Have the other party call you by dialing your • When you receive a call while using the phone number in the same way as you do international roaming service, the call when you are in Japan. is forwarded internationally from Japan, ● Having the other party call you overseas regardless of the country from which from a country outside Japan the call is made. The call is charged You need to have the other party dial the the same as the call to Japan, and the international call access code and "81" receiver is charged the incoming call regardless of the destination because the charge. call is routed through Japan. • Even if the other party has made a call International call access code of the country with notifi cation of the Caller ID set, in which the caller is staying is -81- 90 (or you may not be notifi...
Page 220
S etting International International Automatic Set ON/OFF dial assist conversion of Automatic Roaming function conversions. • When it is turned Setup to use the international roaming service on, an international or international phone calls. dial assist screen • Depending on the overseas network operator, appears for calls roaming cannot be setup in some cases. with "+" entered at From the Home screen, "Phone" the beginning of the X X "Call settings" X " R oaming phone number. Tap settings" "International call" to convert "+" to an Change the settings if necessary international access code registered in Restricting incoming During the international "International prefi x". calls roaming, set to restrict ...
Page 221
N etwork Remote Set network services A fter Returning to service operation such as voicemail Japan (charged) from overseas. • Activate "Remote When you return to Japan, this terminal Caller ID operation settings" automatically connects to the network. If it notifi cation beforehand. is unable to connect, change the following request • For operations settings. service from overseas, • Set "Preferred network type" to "LTE/3G/GSM (charged) international call (Auto)" (P220). Roaming fee to Japan in the • Place a check mark in "Choose automatically" call country you use is ...
Page 222
Appendix/Index ■ Charging T roubleshooting (FAQs) Symptom Check item Cannot • Is the battery pack installed Troubleshooting charge correctly? → P46 • First, check whether software update is notifi cation • Is the adapter plug and required. If so, update the software (Software LED light cigar lighter plug properly Update → P240). does not light inserted into power outlet • If it does not improve after confi rming the up or blink or cigar lighter socket? check items, contact "Repairs" (in Japanese • Are the adapter and this only) on the back cover of this manual or a terminal set properly? repair counter specifi ed . • When using the AC adapter (optional), is the AC adapter ...
Page 223
■ Terminal operations Symptom Check item Battery life is • The battery pack is a Symptom Check item short consumable accessory. Becomes • While operating or The usage duration of hot during charging, or if you operate the battery per 1 charge operation or applications or watch decreases gradually charging TV for a long time while each time the battery charging, the terminal, is recharged. When the battery pack or adapter operation time is too short may become hot. There is even if the terminal is no operation problems and fully charged, purchase a you can continue to use it. new battery pack of the specifi ed type. Battery life is • This terminal, internal short battery or adapter may Power is ...
Page 224
Symptom Check item Symptom Check item Slow reaction • It might occur if a large T erminal • It may be caused by when tapping amount of data is saved operation is applications installed to the the touch in terminal or data with unstable terminal after purchase. If screen or extremely large size are problems improve when you pressing the processed between this start in Safe mode (a function keys terminal and microSD card. to activate the terminal in a mode similar to default), The nano UIM • Is the nano UIM card problems may be improved by card is not inserted in the right uninstalling the application. recognized direction? → P45 - How to activate Safe mode Clock is ...
Page 225
■ Calls Symptom Check item Terminal * When Safe mode Symptom Check item operation is starts, "Safe mode" Cannot make • Is this terminal in Airplane unstable appears on the bottom a call even if mode? → P165 left of the screen. the call key * To stop Safe mode, has been turn the power OFF tapped once and restart it. - Before starting Safe The ringtone • Is the ringtone volume set mode, backup necessary does not to minimum? → P171 data. sound • Is it set to public mode - Widgets that you have (power OFF) or manner ...
Page 226
■ Screen Symptom Check item Calls are not • Turn the power off and on, Symptom Check item connected or remove and attach the The display is • Has the screen backlight does not battery pack or nano UIM timeout been set? disappear card. → P173 when you • Due to the radio wave • Has the screen brightness move, or types, making/receiving been adjusted? → P173 calls cannot calls may be unavailable • Is the battery level low? be made or even with state of "in the → P47 received even service area" and even when • Has power safe been set? when the radio wave is indicated as ...
Page 227
■ Mail ■ TV (Full seg/1Seg) Symptom Check item Symptom Check item Email is not • Is there a check mark in Cannot watch • Are you at a location that received "Email" of "Account & sync"? TV (Full is outside of the digital automatically Place a check mark in it. seg/1Seg) terrestrial broadcast → P111 service area, or where the • Do you set "Update broadcast wave is weak? schedule" to "Manual"? Set • Are the channels Sync schedule. → P110 confi gured? → P137 Can be • For devices that do not ■ Camera viewed support SCMS-T, the TV images, but sound cannot be heard (Full Symptom Check item there is no ...
Page 228
■ Osaifu-Keitai ■ Overseas use Symptom Check item Symptom Check item Osaifu-Keitai • If you remove the battery This terminal ■ Antenna mark appears cannot be pack or activate Omakase is not • Have you applied for used Lock, Osaifu-Keitai function available to WORLD WING? cannot be used regardless use overseas Check whether you have of NFC/Osaifu-Keitai lock applied for WORLD WING. settings. ■ Icon which indicates out of • Is NFC/Osaifu-Keitai set to service area appears lock? → P125 • Are you at a location that is • Did you swipe the mark outside of the international ...
Page 229
Symptom Check item Symptom Check item Data • Set Data roaming to ON. The other • Even if the other party communication → P219 party's has made a call with is not available number is not notifi cation of the Caller overseas displayed/ ID set, you may not be A diff erent notifi ed of the Caller ID This terminal • Has the approximate number is depending on the network has become limit of usage fee been displayed/ or network operator. Also, unusable exceeded? The the number you are notifi ed suddenly For "International roaming ...
Page 230
® ■ Data management ■ Bluetooth function Symptom Check item Symptom Check item ® Data transfer • Are you using a USB HUB? This terminal • Put the Bluetooth is not working If you use a USB HUB, cannot compatible device data transfer may not work fi nd/be (commercial) on standby properly. connected to and register it on this ® a Bluetooth terminal. If you want to The data • Remove and attach compatible delete a registered device saved on microSD card. → P198 device and register it again as a microSD ...
Page 231
■ Map and GPS Function E rror Message Symptom Check item Error Message Description AUTO-GPS • Check if the AUTO-GPS No SIM card The nano UIM card is service function is deactivated due not working properly. information to low battery power. If the problem is not cannot be • Check if the AUTO-GPS resolved by removing set. function is deactivated and reinserting the due to low battery power. nano UIM card, contact If the AUTO-GPS function "Repairs" (in Japanese is deactivated by the "Low- only) on the back cover power operation settings", of this manual. the AUTO-GPS service information cannot be No service You cannot use this set. In that case, change terminal because it is the "Low-power operation ...
Page 232
Error Message Description Error Message Description • Not enough It is displayed when Invalid recipient The phone number space on all there is not enough or contact entered storage. To free space to save a in SMS recipient is up space, delete fi le, application or invalid. The phone some fi les. media contents, or to number unavailable to • If you keep using, operation part function use as a recipient or a some functions or application. You can contact has not been and applications delete fi les or media registered in Contacts may not be contents or uninstall is entered. Enter the operated. Try to applications to ensure correct phone number free space by ...
Page 233
Error Message Description Warranty and After- Sales Service Login information When setting up Email incorrect. Try again account, an incorrect Email address or Warranty password has been input. Input the correct • Be sure to receive a warranty at the time of Email address or purchase of this terminal. Read contents of password. the warranty and confi rm information such Network unavailable When setting up Email as " 販売店名・お買い上げ日 (shop name and account, it cannot date of purchase)" and keep it in a safe access to the server place. If necessary items are not described, due to the abnormality immediately contact the shop of purchase. of the network. Confi rm The warranty for free repair is valid for one the network state. year from the date of purchase. * Back Cover L40, Battery Pack L24, TV Optimizing app XX This will display when Antenna Cable L01 and Mickey Window of XX . you are notifi...
Page 234
* Phonebook data can be saved on microSD caused by your inappropriate handling card in this terminal. (such as damage to external connection * Data such as phonebook entries can be terminals, earphone/microphone jack, LCD, backed up using cloud. etc.), or when it is not repaired by a repair counter specifi ed. • You will be charged even during the After-Sales Service warranty period if malfunction is caused by the use of devices and consumables other When this terminal breaks down than those specifi ed. Before repair, read "Troubleshooting" in this ■ Repair may not be possible in the following manual for detailed information. If the problem cases still persists, contact "Repairs" (in Japanese • When, as the result of inspection, only) on the back of this manual. corrosion is found due to exposure to water, condensation or sweat, or any of the Repairs internal boards are damaged or deformed (damage to the external connection Bring your terminal to a repair counter terminals, earphone/microphone jack, LCD, specifi ed Repairs are accepted during business or cracked body could be the case as well). hours of a repair counter. Also, you must bring ...
Page 235
■ Replacement parts Replacement parts (parts required to maintain functions) will in principle be kept in stock for 4 years after termination of production. However, depending on the malfunctioning part, repair may not be possible due to a lack of replacement parts. Even after the stock period has expired, the repair of some malfunctioning parts may • Note that the settings and other information be possible. Therefore contact "Repairs" (in may be cleared (reset) as a result of Japanese only) on the back of this manual. malfunction, repair or other handling. In this case, make the settings again. Precautions • When the repair is executed, MAC address ® ® of Wi-Fi /Bluetooth address in this terminal • Never modify this terminal or accessories. may be changed regardless of repaired part. - Doing so may result in fi re, injuries or malfunctions. • Magnetic components are used in the parts that - The modifi ed terminal may be repaired only are described below. Do not allow cash cards or if the owner agrees on that all the modifi...
Page 236
Memory dial (Phonebook function) S oftware Update and downloaded data When you change the model or repair this About Software Update terminal, data that has been imported, downloaded or created by you may be The software update is a function which you changed or lost. XXX shall have no liability for can connect to the network and confi rm if an any change or loss of any kind. Under some update is required. It downloads the update fi le circumstances, XXX may replace your terminal as required and installs it. with its equivalent instead of repairing it. In this When the update is necessary, follow the case, most data from the old terminal cannot instructions from (software update) on the be transferred to the replacement terminal. status bar, or visit website. The following contents are included in the software update. In order to use this terminal safely and comfortably, please make sure to update to the latest version. • Function improvement, new functions • Easier to operate • Quality improvement • New security patch Appendix/Index...
Page 237
• During the installation, you cannot make Note a phone call, receive an incoming call, use • The update can be run with the data saved communication functions or other functions. in this terminal. However, the data may not • All key operations are disabled during the be protected depending on your terminal update. The update cannot be stopped either. conditions (malfunction, damage, getting • After fi nishing the update, it will be restarted. wet, etc.). It is recommended to back up • Part of the settings may be initialized after necessary data beforehand. Please note that the update, set them up again. some data cannot be backed up. • If a PIN has been set, the PIN entry screen appears during the restart after rewriting and you are required to enter your PIN. P recautions • Consult a repair counter specifi ed when • Once updating your terminal, you cannot update fails and all operations are disabled. downgrade to any former software. • SMS sent during a software update are • When updating, the original information about stored at an SMS center.
Page 238
• Make sure to upgrade with battery fully Updating Software remained. • Do not power off or remove the battery pack When this terminal needs to update, the update during update. fi le will be downloaded automatically, and the • It is recommended that this terminal be put in installation will then be reserved. (Software a place with good reception and not be moved Update) is displayed on the status bar. while downloading. The update may stop When it is purchased, the setting of when it is put in a place with bad reception. automatically reserving installation is set to ® • When the download via Wi-Fi starts, fi nish "ON". the download without moving it out of • Depending on the update contents, it needs ® the Wi-Fi environment. If the download is you to install it without installation being ® discontinued due to the Wi-Fi disconnection, reserved. "Download stopped【Reason】 ・No Service" Drag or swipe the status bar downward ...
Page 239
Changing installation reservation W hen the icon is not displayed on time status bar You can change the reserved time yourself. Follow the procedures below to update. ■ Install immediately From the Home screen, "Apps" X "Settings" X "About phone" Drag or swipe the status bar X "Update Center" X "Software downward to open the notifi cation Update" X "Start Update" panel X tap a notifi cation • When there is a update fi le, the update starts. "Start Update" X "OK" After the download fi nished, "Start installing" X "OK" ■ Changing the reserved time • The installation starts. Drag or swipe the status bar • If the "OK" was not tapped, the installation downward to open the notifi cation starts after 10 seconds. panel X tap a notifi cation • ...
Page 240
Select "Download and install" or Application Update "Download" • "Download and install": After the ■ After the update, check if there are any download is fi nished, the installation is application updates. If the applications are implemented automatically. not updated, the performance will not be • "Download": Even after the update fi le stable, or the functions are improper. Please has been downloaded, the installation make sure to update to the latest version. is not implemented automatically. To • Update from the notifi cation icon install, you need to implement the After the update is fi nished, restart this installation yourself. terminal and the notifi cation icon (Updating has been completed) will appear. Note Drag or swipe the status bar downward to • When the software in this terminal is the open the notifi cation panel X "Updating latest one, "No upgrade is needed. Use it has been completed" X "OK", update the as it is." appears. applications from the update list.
Page 241
connections. • For precautions on application update, refer Change settings if necessary to "Precautions" (P241) of software update. • For the latest software information, refer to Update Set to automatically check LG Electronics website. notifi cation whether there are updatable http://www.lg.com/jp/support/software- cycle apps, and set the notifi cation manuals (In Japanese only) cycles. Auto- Set to automatically update D ownloads update upgradeable apps or not. apps From the Home screen, "Apps" X "Settings" X "About phone" X "Update Center" X "App Updates" • When "Legal Documents for LG Software" screen is displayed, "Next" X confi rm "Terms of Use for LG Software" and "LG Software Privacy Policy", then place a check mark X "Agree". "Download" Appendix/Index...
Page 242
M ain Specifi cations AC adapter Approx. 140 minutes 05 (optional) Charging time Terminal DC adapter Approx. 140 minutes 04 (optional) Model name KS1604 Watch time Approx. 340 minutes Size (H×W×D) Approx. 144 mm× Record Approx. 2640 1Seg Approx. 74 mm× time * minutes (saved in the Approx. 9.6 mm internal storage) (Max. thickness: Approx. 10.8 mm) Watch time Approx. 300 minutes Weight Approx. 149 g Record Approx. 70 minutes Full seg time (saved in the internal ...
Page 243
® Type CMOS with fl ash on Bluetooth Line-of-sight Within approx. 10 Image the back side communication meters pickup distance * Size Main camera: 1/3.0 inch device Front camera: 1/6.9 inch Compatible HFP, HSP, OPP, SPP, fi le * HID, A2DP, AVRCP, Eff ective pixels Main camera: Approx. PBAP, PAN (PAN- 13.2 million pixels NAP), PAN (PANU), Front camera: Approx. aptX, SBC 2.4 million pixels Earphone/ Terminal Recorded pixels Main camera: Approx. 3.5φ microphone diameter (maximum) 13.1 million pixels jack...
Page 244
*4 This varies depending on the obstacles • Charging time is an estimate for charging an between the communicating devices and empty battery pack with the terminal power the reception quality. off . For charging with the terminal power on, it ® *5 These are Bluetooth standards that takes longer. provide specifi cations for communications ® between Bluetooth compatible device. Battery Pack L24 • Continuous call time is an estimate of the battery life during a continuous call with Battery type Lithium-ion battery normal signal reception. Nominal voltage 3.8 V • Continuous standby time is an estimate of the battery life during a continuous Nominal capacity 2,920 mAh standby with normal signal reception. In certain circumstances, the standby time TV Antenna Cable L01 may drop to as low as half the time shown due to the battery charge, function settings, Length Approx. 140 mm temperature, or radio wave reception in the ...
Page 245
Languages compatible F ile format This terminal supports the display or playback ■ Display languages of the following fi le formats. Japanese/English * Azerbaijani/Indonesian/Malay/Bosnian/ Type File formats Catalan/Czech/Danish/German/Estonian/ Spanish/Basque/French/Arabic/Croatian/ Audio mp3, m4a, wav, ogg, amr, wma, Icelandic/Italian/Swahili/Kurdish/Latvian/ aac, mka, mid, fl ac, isma, 3ga, xmf Lithuanian/Hungarian/Dutch/Norwegian/ Image bmp, gif, jpeg, png, wbmp, webp Uzbek/Polish/Portuguese/Romanian/ Slovak/Slovenian/Finnish/Swedish/ Video mp4, 3gp, m4v, mkv, wmv, avi, ts, Vietnamese/Turkish/Greek/Bulgarian/ ogm, webm, ismv, asf Kazakh/Serbian/Ukrainian/Georgian/ Photos and videos are saved in the following Armenian/Farsi/Nepalese/Marathi/Hindi/ fi le formats. Bengali/Punjabi/Gujarati/Tamil/Telugu/ Kannada/Malayalam/Sinhalese/Thai/ Type File formats Burmese/Cambodian/Korean/Chinese Photo...
Page 246
Estimate number of photos and video S pecifi c Absorption Rate ■ Number of shooting photos (estimate) (SAR) of Mobile Phones KS1604 microSD card This model [KS1604] mobile phone complies Resolution (main unit)* (1GB) with Japanese technical regulations and international guidelines regarding exposure to 3120×3120 Approx.1,900 Max. approx. radio waves. (9M) This mobile phone was designed in observance of Japanese technical regulations regarding The number of images when the fi le size is 4 MB. exposure to radio waves(*1) and limits to * The number of saved images at the time of exposure to radio waves recommended by a purchase. set of equivalent international guidelines. This ■ Video recording time (estimate) set of international guidelines was set out by the International Commission on Non-Ionizing KS1604 microSD card Resolution Radiation Protection (ICNIRP), which is in ...
Page 247
power level, the actual SAR level of the phone R adio Frequency (RF) while operating can be well below the maximum Signals value. This is because the phone is designed to operate at multiple power levels so as to use THIS MODEL PHONE MEETS THE U.S. only the power required to reach the network. In GOVERNMENT'S REQUIREMENTS FOR general, the closer you are to a wireless base EXPOSURE TO RADIO WAVES. station antenna, the lower the output. Your wireless phone contains a radio Before a phone model is available for sale transmitter and receiver. to the public, it must be tested and certifi ed Your phone is designed and manufactured not to the FCC that it does not exceed the limit to exceed the emission limits for exposure established by the U.S. government-adopted to radio frequency (RF) energy set by the requirement for safe exposure. The tests Federal Communications Commission of are performed on position and locations (for the U.S. Government. These limits are part example, at the ear and worn on the body) as of comprehensive guidelines and establish required by FCC for each model.The highest permitted levels of RF energy for the general SAR value for this model phone as reported population. The guidelines are based on to the FCC when tested for use at the ear is standards that were developed by independent 0.440 W/kg, and when worn on the body is scientifi c organizations through periodic and 1.420 W/kg. (Body-worn measurements diff er thorough evaluation of scientifi...
Page 248
The FCC has granted an Equipment ® Wi-Fi This device is capable of Authorization for this model phone with all Caution operating in 802.11a/n mode. reported SAR levels evaluated as in compliance For 802.11a/n devices operating with the FCC RF exposure guidelines. SAR in the frequency range of 5.15 - information on this model phone is on fi le with 5.25 GHz, they are restricted for the FCC and can be found under the Display indoor operations to reduce any Grant section at http://transition.fcc.gov/oet/ potential harmful interference for ea/fccid/ after search on FCC ID ZNFHRF. Mobile Satellite Services (MSS) in For body worn operation, this phone has the US. been tested and meets the FCC RF exposure WIFI Access Points that are guidelines. Please use an accessory capable of allowing your device to designated for this product or an accessory operate in 802.11a/n mode(5.15 which contains no metal and which positions - 5.25 GHz band) are optimized for the handset a minimum of 1.5 cm from the indoor use only. body. If your WIFI network is capable of operating in this mode, please In the United States, the SAR limit for restrict your WIFI use indoors to wireless mobile phones used by the not violate federal regulations to public is 1.6 watts/kg (W/kg) averaged ...
Page 249
Part 15.105 statement F CC Statement for the This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide This device complies with part15 of FCC reasonable protection against harmful rules. Operation is subject to the following two interference in a residential installation. conditions: This equipment generates uses and can (1) This device may not cause harmful radiate radio frequency energy and, if not interference. installed and used in accordance with the (2) This device must accept any interference instructions, may cause harmful interference received, including interference that may to radio communications. However, there is cause undesired operation. no guarantee that interference will not occur in a particular installation. if this equipment Part 15.21 statement does cause harmful interference or television Change or Modifi cations that are not expressly reception, which can be determined by approved by the manufacturer could void the turning the equipment off and on, the user is user's authority to operate the equipment. encouraged to try to correct the interference by one or more of the following measures: Part 15.19 statement - Reorient or relocate the receiving antenna. This device complies with part15 of FCC rules.
Page 250
E uropean Union Directives I mportant Safety Conformance Statement Information AIRCRAFT Switch off your wireless device when boarding an aircraft or whenever you are instructed to do Hereby, LG Electronics Inc. declares that this so by airline staff . If your device off ers a 'fl ight product is in compliance with: mode' or similar feature consult airline staff as • The essential requirements and other relevant to whether it can be used on board. provisions of Directive 1999/5/EC DRIVING • All other relevant EU Directives Full attention should be given to driving at all The above gives an example of a typical times and local laws and regulations restricting Product Approval Number. the use of wireless devices while driving must be observed. ® Wi-Fi This device is intended for sale in (WLAN) Japan only. HOSPITALS This equipment may be operated ...
Page 251
PETROL STATIONS Hearing Aids Obey all posted signs with respect to the use Some digital wireless phones may interfere of wireless devices or other radio equipment with some hearing aids. In the event of in locations with fl ammable material and such interference, you may want to consult chemicals. Switch off your wireless device your hearing aid manufacturer to discuss whenever you are instructed to do so by alternatives. authorized staff . NOTE : Excessive sound pressure from earphones and headphones can cause INTERFERENCE hearing loss. Care must be taken when using the phone in close proximity to personal medical devices, To prevent possible hearing damage, such as pacemakers and hearing aids. do not listen at high volume levels for long periods. Pacemakers Pacemaker manufacturers recommend that a minimum separation of 15cm be maintained For other Medical Devices: between a mobile phone and a pacemaker to Please consult your physician and the device avoid potential interference with the pacemaker. manufacturer to determine if operation of your To achieve this use the phone on the opposite phone may interfere with the operation of your ear to your pacemaker and do not carry it in a medical device. breast pocket. CAUTION RISK OF EXPLOSION IF BATTERY IS ...
Page 252
E xport Administration I ntellectual Property Regulations Right Japan Export Control Regulations ("Foreign Exchange and Foreign Trade Law" and relevant C opyrights and Portrait laws and regulations) may apply to this product Rights and its accessories. U.S. Re-export Regulations (Export Administration Regulations) applies to You have no right to copy, modify, or distribute this product and its accessories. If you export contents such as text, images, music, map or re-export this product or its accessories, data, or software downloaded from websites please follow the necessary procedures at on the Internet, or photos shot by the camera your own risk and expense. For details on the of this product without permission from the procedures, contact the Ministry of Economy, copyright holder except when the copy or Trade and Industry or the U.S. Department of quote is for personal use that is allowed under Commerce. Copyright Law. Note that it may be prohibited to shoot or record live performances or exhibitions even for personal use. Refrain from taking portraits of other people and uploading such portraits to websites using this product without their consent, as this violates portrait rights. Appendix/Index...
Page 253
® ® ® • Microsoft , Windows , Windows Vista , and T rademarks ® Windows Media are trademarks or registered trademarks of Microsoft Corporation in the • "Catch Phone (Call waiting service)" is a United States and/or other countries. registered trademark of Nippon Telegraph and • Google and Google logo, Android, Google Play Telephone Corporation. and Google Play logo, Google Map, Google • The microSD Logo, microSDHC Logo, and Calendar, Google+ and Google+ logo, Gmail microSDXC Logos are the trademarks of SD- and Gmail logo, YouTube and YouTube logo 3C, LLC. are trademarks or registered trademarks of Google, Inc. • HDMI (High-Defi nition Multimedia Interface) is • The Bluetooth word mark and logos are trademarks or registered trademarks of HDMI owned by the Bluetooth SIG, INC. and any use Licensing LLC. of such marks by XXX, INC. is under license. ®...
Page 255
U nlocking SIM Information Unlocking SIM is available on this terminal. Unlocking SIM enables a SIM card from other To obtain the source code under GPL, LGPL, makers to be used. MPL and other open source licenses, that is • The service and function may be limited. XXX contained in this product, please visit shall not be liable for performance. http://opensource.lge.com . • For details on unlocking SIM lock, refer to In addition to the source code, all referred website. license terms, warranty disclaimers and copyright notices are available for download. Insert a SIM card of other LG Electronics will also provide open source manufacturers code to you on CD-ROM for a charge covering Press the power key for 2 seconds the cost of performing such distribution (such or longer as the cost of media, shipping, and handling) upon email request to opensource@lge.com. • "Network locked" appears on the lock This off er is valid for three (3) years from the screen. date on which you purchased the product. When the screen is locked, set a method to unlock it Input SIM unlock code in "SIM network unlock PIN" fi eld X "UNLOCK"...