Table of Contents
Advertisement
Quick Reference Guide
Section 9
Problem
Unit running in AUTO but no
power in house.
Unit shuts down during
operation.
Unit shuts down during
operation.
Unit was running and shuts
down, attempts to restart.
Unit will not start in AUTO with
utility loss.
Unit will not start in AUTO with
utility loss.
Unit will not start in AUTO with
utility loss.
Unit will not start in AUTO with
utility loss.
Unit will not start in AUTO with
utility loss.
Unit will not start in AUTO with
utility loss.
Unit will not start in AUTO with
utility loss.
Unit will not start in AUTO with
utility loss.
Unit will not start in AUTO with
utility loss.
Unit will not start in AUTO with
utility loss.
Unit will not start in AUTO with
utility loss.
Unit will not start in AUTO with
utility loss.
Unit will not start in AUTO with
utility loss.
Yellow LED illuminated in any
state.
Yellow LED illuminated in any
state.
Yellow LED illuminated in any
state.
Yellow LED illuminated in any
state.
Yellow LED illuminated in any
state.
Yellow LED illuminated in any
state.
LED
Things to Check
GREEN
Check MLCB.
RED
Check the LED's / Screen for
alarms.
RED
Check the LED's / Screen for
alarms.
RED
check the LED's / Screen for
alarms.
NONE
See if screen says unit not
activated.
GREEN
Check screen for start delay
countdown.
RED
Check the LED's / Screen for
alarms.
RED
Check the LED's / Screen for
alarms.
RED
Check the LED's / Screen for
alarms.
RED
Check the LED's / Screen for
alarms.
RED
Check the LED's / Screen for
alarms.
RED
Check the LED's / Screen for
alarms.
RED
Check the LED's / Screen for
alarms.
RED
Check the LED's / Screen for
alarms.
RED
Check the LED's / Screen for
alarms.
RED
Check the LED's / Screen for
alarms.
RED
Check the LED's / Screen for
alarms.
YELLOW
Check the screen for
additional information.
YELLOW
Check the screen for
additional information.
YELLOW
Check the screen for
additional information.
YELLOW
Check the screen for
additional information.
YELLOW
Check the screen for
additional information.
YELLOW
Check the screen for
additional information.
Active Alarm
Solution
NONE
Check MLCB if the MLCB is in the ON position. If it is in
the ON position contact the servicing dealer.
HIGH TEMPERATURE
Check ventilation around the generator, intake, exhaust
and rear of generator. If no obstruction contact serving
dealer.
OVERLOAD REMOVE
Clear alarm and remove household loads from the
LOAD
generator. Put back in AUTO and restart.
RPM SENSE LOSS
Clear alarm and remove household loads from the
generator. Put back in AUTO and restart. It may be a fuel
issue so contact the servicing dealer.
NOT ACTIVATED
Refer to activation section in owners manual.
None
If the start up delay is greater than expected, contact
servicing dealer to adjust from 2 to 1500 seconds.
LOW OIL PRESSURE
Check Oil Level / Add Oil Per Owners Manual. If oil level
is correct contact servicing dealer.
RPM SENSE LOSS
Clear alarm. Check the battery using the control panel
under the MAIN menu using the BATTERY MENU
option. If it states battery is GOOD contact servicing
dealer. If it states CHECK BATTERY replace the battery.
OVERCRANK
Check fuel line shutoff valve is in the ON position. Clear
alarm. Attempt to start the unit in MANUAL. If it does not
start or starts and runs rough, contact servicing dealer.
LOW VOLTS REMOVE
Clear alarm and remove household loads from the
LOAD
generator. Put back in AUTO and restart.
FUSE PROBLEM
Check the 7.5 Amp fuse. If it is bad replace it with an
ATO 7.5 Amp fuse, if not contact servicing dealer.
OVERSPEED
Contact servicing dealer.
UNDERVOLTAGE
Contact servicing dealer.
UNDERSPEED
Contact servicing dealer.
STEPPER
Contact servicing dealer.
OVERCURRENT
MISWIRE
Contact servicing dealer.
OVERVOLTAGE
Contact servicing dealer.
LOW BATTERY
Clear alarm. Check the battery using the control panel
under the MAIN menu using the BATTERY MENU
option. If it states battery is GOOD contact servicing
dealer. If it states CHECK BATTERY replace the battery.
BATTERY PROBLEM
Contact servicing dealer.
CHARGER WARNING
Contact servicing dealer
SERVICE A
Perform SERVICE A maintenance, hit ENTER to clear.
SERVICE B
Perform SERVICE B maintenance, hit ENTER to clear.
Inspect Battery
Inspect Battery, hit ENTER to clear.
31
Advertisement
Table of Contents
