Advertisement
2. INTRODUCTION & SPECIFICATIONS
Manufactured from corrosion resistant materials with stainless steel body and motor case. Massive maximum head of 40mtr makes this unit
ideal for wells. fitted with automatic cut-out. Minimum water depth of 32mm. Designed for clean water although these pumps will accept small
particles up to 0.5mm. Suitable for the effective drainage of cellars, sinks, cisterns, baths and the general transfer of water.
Model no:................................ WPS92A
cutout:.....................................Automatic
outlet:......................................1" BSP female
Maximum output:.................... 92ltr (20gal)/minute
Minimum Water Depth:............32mm
Maximum Water Depth:...........7mtr.
Maximum Particle Size:...........0.5mm
Maximum Head:......................40mtr.
Motor Power:...........................1000W
Supply:.................................... 230V
3.
OPERATING INSTRUCTIONS
WARNING! Ensure you read, understand and apply safety instructions.
IMPORTANT . As a guide limit the maximum continuous running time for the pump to six hours, followed by three hours downtime.
3.1.
fit appropriate discharge pipe to pump outlet and secure with clip. Ensure the diameter of the discharge pipe is same as, or greater
than, the outlet diameter. A smaller pipe will adversely effect the pump flow rate.
3.2.
Position pump in the water, and place the outlet pipe securely in the discharge receptacle or area. We recommend the pump is
submerged with its discharge outlet facing up to release any trapped air.
3.3.
Plug the pump into the electrical mains supply and switch on. The pump will automatically turn on as the level of water rises (fig.3A).
As water level lowers, the float will automatically switch the pump off as it reaches the minimum height (fig.3B). The float may be
adjusted by shortening or lengthening the cable using the notch in the handle. The pump will switch on if the water level is up to or
above the maximum length of the float cable. To function correctly the float must move freely. Ensure the float can do so and
that the cable is not restricted. check that the pump and discharge are working correctly.
3.4.
The water into which the pump is placed will act as the motor cooling agent. for this reason the pump must remain submerged at all
times. Should the pump have to be used in shallow water DO NOT operate for more than 10 minutes. failure to follow this rule will
damage the unit and will invalidate your warranty.
NOTE: See fig.4 to determine minimum clearance required if using the pump in a restricted area, such as a well or a trough.
4. MAINTENANCE
WARNING! With the exceptions listed below in "TROUBLESHOOTING", all pump, float, electrical cable service/maintenance and
repair must only be undertaken by an authorised service agent. Failure to observe this rule may be dangerous and will invalidate
your warranty.
WARNING! Ensure the pump is disconnected from the mains power supply before attempting any service or maintenance.
4.1.
Keep all parts of the pump clean. rinse, drain and allow to dry before storing pump.
4.2.
regularly check the water inlet on the base of the pump to ensure there are no blockages. To access the impeller, carefully undo the
base screws and remove base. clean impeller and replace base ensuring that the "o" ring is correctly located.
DO NOT dismantle any other part of the unit.
TROUBLESHOOTING
1. Water level below minimum suction depth.
a. Motor operates but
2. Air bubbles in pump accumulated during submersion,
there is no suction.
3. clogged intake filter or discharge pipe
b. reduced water
1. Discharge pipe bent, or pinched.
volume for level
2. Discharge pipe too narrow.
of water
3. Pump partially blocked.
c. The pump will not
1. no electrical power.
start or suddenly
2. float not working
stops during
3. Impeller is jammed.
operation.
Environmental Protection.
recycle unwanted materials instead of disposing of them as
waste. All tools, accessories and packaging should be sorted,
taken to a recycle centre and disposed of in a manner which
is compatible with the environment.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
© Jack Sealey Limited
or float is incorrectly positioned so pump does not stop
at minimum level and sucks in air.
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7Ar
1" BSP
female
port
Moulded 3 pin plug
with 10mtr flying lead
fig.2
WEEE Regulations.
Dispose of this product at the end of its working life in compliance
with the Eu Directive on Waste Electrical and Electronic Equipment.
When the product is no longer required, it must be disposed of in an
environmentally protective way. contact your local solid waste
authority for recycling information.
Original Language Version
Moulded
carry/hoist
handle
float
switch
fig.4
500 500
1. Stop the pump.
2. release air by inclining the pump and
re-immersing it in water.
3. remove dirt, and clean the unit.
1. Straighten pipe
2. use wider diameter pipe.
3. clean pump.
1. check cable, plug and fuse.
2. contact authorised service agent.
3. clean the pump.
www.sealey.co.uk
01284 757500
Web
sales@sealey.co.uk
01284 703534
email
WPS92A
fig.3
Issue: 1 - 14/11/13
Advertisement
