Quoizel MBH8407K Assembly Instruction Sheet

6 CORPORATE PARKWAY
, .
GOOSE CREEK SC 29445
. .
www quoizel com
Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (1) A19 Medium Base Bulb 100W Maximum
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Fixture can only be mounted in the direction indicated on page 2.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Fixture Body
A
x 1
-
STEP 1 Instal Shade
A. Unscrew the Lock Screw, remove the Cage, the Glass Shade and
the Tab from the Fixture Body ( ).
inside of the shade.
B. Place Glass Shade into the Cage, secure by place the Tab into the
Cage press on the Glass Shade.
C. Align the label "A" on the bottom of the fixture hood to the label "A"
on the top edge of the cage. Place the fixture hood onto the top
edge of the cage and secure with lock screws. Hand tighten until
snug with screwdrivers.
Figure 1
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
2017 QuoizelInc.
Assembly Instruction Sheet #IS-MBH8407K
for product cleaning tips. Go to the
30-45 minutes
Crossbar Assembly
B
x 1
Alternate
Mounting
C
screw
x 2
A Remove the Styrofoam from
Fixture Hood
Label "A"
Tab
Glass Shade
Label "A"
Lock Screw
Cage
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
For Style MBH8407K
Care + Maintenance selection.
-
STEP 2 Install Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (B). Attach
the Crossbar Assembly (B) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (C) if your
installation requires a shorter mounting screw.
Outlet Box
Mounting Screw
or Alternate Short
Mounting Screw
-
STEP 3 Test Fit the Backplate to the Crossbar Assembly
A. Remove the mounting balls from the Crossbar Assembly (B). Place
the backplate and Fixture Body (A) onto the Crossbar Assembly (B)
and secure with mounting balls. Note: The backplate and Fixture
Body (A) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screws
or alternate short mounting screws on the Crossbar Assembly (B)
by unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws or alternate short mounting screws
in or out of the crossbar until the correct length is achieved. Once
the backplate and Fixture Body (A) is secure, remove the mounting
ball and Fixture Body (A) and proceed to Step 4.
Figure 3
1of2
_R1
.
Supply Wires with
Ground Wire
B
Outlet Box Screws
(not included)
Figure 2
Mounting Screw
or Alternate Short
Backplate
Mounting Screw
Mounting Ball
B
Hex Nut and
Lock Washer
RevisedDate:2017-08-03
A