Table of Contents
Advertisement
Quick Links
ELECTRIC TELESCOPIC HEDGE TRIMMER AND
BRANCH LOPPER SET MODEL EKETC01
INSTRUCTION MANUAL
回
Please read these instructions carefully and make sure you understand them before using the
electric telescopic hedge trimmer and branch lopper set
PLEASE READ AND SAVE THESE INSTRUCTIONS FOR FURTHER REFERENCE!
ANY QUESTIONS OR PROBLEMS? Please call the ECKMAN Helpline on: 0844 441 3011 or go to www.ECKMAN.co.uk
Advertisement
Table of Contents
Related Manuals for Eckman Elite EKETC01
Summary of Contents for Eckman Elite EKETC01
- Page 1 ELECTRIC TELESCOPIC HEDGE TRIMMER AND BRANCH LOPPER SET MODEL EKETC01 INSTRUCTION MANUAL 回 Please read these instructions carefully and make sure you understand them before using the electric telescopic hedge trimmer and branch lopper set PLEASE READ AND SAVE THESE INSTRUCTIONS FOR FURTHER REFERENCE!
-
Page 2: Table Of Contents
Contents I. Technical Data....................3 II. Intended Use....................3 III. Explanation of Symbols on your product..........4 IV. Safety Instructions..................4-9 V. Part Identification..................9-10 VI. Assembly....................10-15 VII. e ..................16 VIII. Connection…...................16 IX. Operation....................16-18 X.Maintance And Servicing................18 XI.Guarantee.....................18 XII.EC Declaration Of Conformity..............19 XIII. Exploded View & Parts List..............20-23... -
Page 3: Technical Data
I. Technical Data： Model PHCEG02A-450/ PHCEG02A (EKETC01) 230V-240V～/50Hz Voltage/Frequency Input Power 450W/710W No load speed (Hedge 1800/min ./6500/min trimmer /Branch Lopper) Noise emission value LWA measured 95dB(A) / 99 dB(A) (Hedge trimmer /Branch Lopper) Hand / arm vibration a vhw <... -
Page 4: Explanation Of Symbols On Your Product
III. Explanation of Symbols on your product WARNING ! Read the user instructions carefully to make sure you understand all the controls and what they do. Remove plug from the mains immediately if the cable is damaged or cut. Do not expose to rain. Do not leave the product outdoors while it is raining. - Page 5 General Power Tool Safety Warnings WARNING ! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and /or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains operated (corded) power tool or battery operated (cordless) power tool.
- Page 6 Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and /or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
- Page 7 the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5. Service Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
- Page 8 for storage. Do not repair a damaged cable. Replace it with a new one. Always wind cable carefully, avoiding kinking. Use only on AC mains supply voltage shown on the product rating label. Under no circumstances should an earth be connected to any part of the product. This product is double insulated and does not require an earth.
-
Page 9: Part Identification
Maintenance and storage RISK OF INJURY ! Do not touch blades. → When finishing or interrupting work fit protective cover. Keep all nuts, bolts and screws secure to be sure the telescopic hedge trimmer is in safe working condition. Store disconnected, in a safe dry environment out of the reach of children. V. -
Page 10: Assembly
1. Shoulder Strap 2. Strap Connector 3. Main Handle 4. Throttle Control Locking Button 5. On/Off Switch 6. Power Cord (10m supplied with UK specifications) 7. Plug (European plug illustrated. Fused BS Approved Plug Supplied) 8. Extension Pole Locking Hexagon Screw (tighten with Hex key (included)) – in some cases instead of the hex key a hand tightening knob is provided for convenience 9. - Page 11 Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious personal injury. Shoulder Strap Assembly Connect the end of the strap with the spring clip to the handle as per Figure 15 below: Fig 15 Connect the other end of the strap with the ‘quick-release’...
- Page 12 Fig 17 Fig 18 Telescopic Hedge Trimmer Assembly One-time assembly is required Remove from packaging and extend the telescopic pole to its longest operating position as shown in Figure 1 as below. Fig 1 Using the Hand Knob supplied to tighten the extension pole by turning the knob clockwise. Make sure the knob has been tightened completely.
- Page 13 Fig 2 Adjusting the extension pole length: Release the extension pole knob by turning it anti-clockwise. Place one hand on one pole section and the other hand on the other section. Pull the pole sections together to shorten the overall length or pull apart to lengthen. See Figure 19 below; Fig 19 NOTE: Extend the telescopic pole only to the length required to reach the hedges and branches being...
- Page 14 Fig 3 Fit and tighten the two Head Locking Knobs - see Figure 4 bellow. (Note The locking knob fixing holes should be on the same side with the extension pole Locking Knob fixing holes) Fig 4 Installing the guide bar and saw chain to the chainsaw/lopper attachment: 1.
- Page 15 Fig 8 See Fig 9 . Fig 9 3.Adjust the chain tension by turning the chain tension SDS outer knob until the tie straps just touch the bottom of the bar rail. Turning clockwise tightens the chain tension. Then check the chain for smooth rotation and proper tension while moving it by hand (wear gloves).
-
Page 16: A P P L I C A T I O N R A N G E
NEVER use the chainsaw without chain oil as this will cause almost immediate damage and will not be covered by the warranty. A small empty 100ml capacity bottle is supplied to measure the oil for filling the branch lopper oil tank. Only fill the oil reservoir ¾ full. Do not over-fill more than 3/4. Chain oil is available from all good retailers of garden machinery and DIY stores. - Page 17 STARTING AND STOPPING See Figure 11 as bellow. Fig 11 Connect the hedge trimmer plug to power supply. To start the blade movement, push the lock-off button and then pull the trigger switch. To stop blade movement, release the trigger switch. ADJUSTING PIVOTING HEAD See Figure 12.
-
Page 18: X.maintance And Servicing
Always keep both hands on the hedge trimmer/branch lopper handles. Never hold shrubs or branches with one hand and operate hedge trimmer /branch lopper with the other. Failure to heed this warning can result in serious injury or even death. WARNING: Clear the area to be cut before each use. -
Page 19: Xii.ec Declaration Of Conformity
Equipment Category - (As defined in the Directive) Product Name:ELECTIC HEDGE TRIMMER AND BRANCH LOPPER SET Factory Model/ECKMAN Model: PHCEG02A-450/EKETC01 Description: 230-240V/50HZ The technical documentation is kept by:Ningbo Energy Power Tools Co., Ltd Add: Chengjia Cun Dongqiao Industrial Zone, Yinzhou District, Ningbo 315157 China, The conformity assessment procedure followed was in according with annex (EN60745-1:2009+A11.EN ISO... -
Page 20: Exploded View & Parts List
XIII. Exploded View & Parts List NAME NAME Cable and plug Lock set A Bushing Tamper screws M5*14 Isobar board Hexagon nuts M5 Screw ST4*16 Big extension rod Screw ST3*10 Knob Terminal Neck Stopper Hang buckle Right power joint Foam soft set Left power joint Block set Left handle... - Page 21 NAME NAME Chain saw joint lower cover Chain oil tank seals Nut M6 Chain oil tank Left hosing Short fuel tank Capacitor Screw ST4*12 Bearing housing Small oil pump Bearing 628 Long fuel tank cCarbon brush Guides to adjust the pieces Brush holder Cross recessed long screws Brush holder briquetting...
- Page 22 Small oil pump Locating bush Woodruff key Guides cover BIg gear Guides Briquetting Positioning shaft Chain wheel Circlip ø12 Sprocket gasket Circlip ø9 Socket screw M6*32 Bearing 609 Right hosing Chain gas tank cap Connection fixed button The oiler Gellar ring 89 Chain saw joint upper cover Ring-pull briquetting...
- Page 23 NAME NAME Connection fixed button Locknut M5 Joint cover of hedge trimmer Washer ø5 Right rotating button Greed washer ø5 Rotating button support Screw ST5*20 Rotating button spring Center support Left rotating button Washer of Driven wheel(1mm) Joint lower cover of hedge trimmer Needle bearing HK0812 Left hosing Gear...