ABB HT610930 Operation Manual page 199

Operation Manual / A150-M56/66/57/67 - A155-M..
Tables
Tables
Table 1: Definition of pictograms ............................... 9
Table 2: Personal protective equipment to be worn
at all times ...................................................................... 14
Table 3: Personal protective equipment to be worn
specific to the respective task ................................... 14
Table 4: Weight of complete turbocharger unit .... 29
Table 5: Fitting the turbocharger, value X, L........... 36
Table 6: Torque-controlled tightening of the pres-
sure screws ................................................................... 38
Table 7: Lubricating oil pressure at oil inlet before
turbocharger ................................................................. 45
Table 8: Lubricating oil temperature at the inlet... 46
Table 9: Maximum lubricating oil temperature at the
outlet .............................................................................. 46
Table 10: Tightening torque (86505)........................ 50
Table 11: Expected replacement intervals ............... 56
Table 12: Maintenance table....................................... 59
Table 13: Parameters for wet cleaning of com-
pressor ........................................................................... 62
Table 14: Turbine wet cleaning, recommended oper-
ating state ..................................................................... 65
Table 15: Wet cleaning of turbines, parameters for 1-
nozzle cleaning.............................................................. 66
Table 16: Wet cleaning of turbines, parameters for 6-
nozzle cleaning.............................................................. 67
Table 17: Tightening torque (81272) .......................... 72
Table 18: Tightening torque (81273) .......................... 72
Table 19: Value table for soaking ............................... 77
Table 20: Tightening torque (81152 / 81154) ........... 81
Table 21: Malfunctions when starting - Delayed
start-up .......................................................................... 82
Table 22: Malfunctions when starting - Vibrations 82
Table 23: Malfunctions when starting - Rubbing of
rotating parts................................................................ 82
Table 24: Malfunctions during operation - Lubricat-
ing oil pressure too low............................................... 83
Table 25: Malfunctions during operation - Speed re-
duces............................................................................... 83
© Copyright 2022 ABB. All rights reserved.
Table 26: Malfunctions during operation - Speed in-
creases............................................................................. 83
Table 27: Malfunctions during operation - Exhaust
gas temperature too high............................................ 84
Table 28: Malfunctions during operation - Charge air
pressure too low ............................................................ 84
Table 29: Malfunctions during operation - Charge air
pressure too high .......................................................... 85
Table 30: Malfunctions during operation - Engine
performance losses....................................................... 85
Table 31: Malfunction - Turbocharger surging ........ 86
Table 32: Malfunction - Sporadic surge blows ........ 86
Table 33: Malfunctions when stopping - Runout
noises ............................................................................... 87
Table 34: Malfunctions when stopping - Runout
time too short ................................................................ 87
Table 35: Malfunction of the speed measurement
system - No signal or poor signal amplitude .......... 88
Table 36: Malfunction of the speed measurement
system - Measured speed too high ........................... 88
Table 37: Malfunction of the speed measurement
system - Measured speed too low............................. 88
Table 38: Swivel lifting eyes......................................... 90
Table 39: Press-off screws........................................... 91
Table 40: Dismantling screw ....................................... 91
Table 41: Weights of assemblies ................................ 96
Table 42: Tightening torques ...................................... 97
Table 43: Tightening torques for insulation ............ 98
Table 44: 3 press-off screws ..................................... 105
Table 45: 6 press-off screws ..................................... 106
Table 46: Tightening torque (90012-01) .................. 111
Table 47: Permissible clearances A and B ................ 116
Table 48: Nozzle ring compression PD ..................... 117
Table 49: Tightening torque (90012-01) ................. 120
Table 50: Tightening torque (51007) ........................ 121
Table 51: Tightening torque (79041)........................ 122
Table 52: Tightening torque (72011) ....................... 123
Table 53: Permissible clearances N and R............... 126
HZTL4032_EN Revision S February 2022