Advertisement
Quick Operation
Power On
1
1. Dig the groove to disassemble the device. Remove the front and rear panel. Remove the
insulating strip to power on the device.
Note: Do not disassemble the device with sharps.
2. Assemble the front panel and rear panel by aligning the Indicator groove on the front panel with
the indicator light pipe on the rear panel.
4
2
Pair Keyfob
1. Power on the swing barrier.
2. After entering the normal mode, set
bit-1 of the four-bit DIP switch on the
master lane control board to ON and
the swing barrier will enter the pairing
mode.
6
Indicator Light Pipe
Indicator Groove
3. Reboot the swing barrier and make
sure no other swing barriers have paired
with the keyfob within the available
pairing distance.
4. Hold Close for more than 10s, the
keyfob starts pairing.
Within 50 cm
After pairing completed, the keyfob's
indicator will flash twice.
If pairing failed, the indicator is off.
You can also pair the keyfob via
iVMS-4200 control client. For details,
see Remote Configuration in User
Manual of Swing Barrier.
5
7
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.
FCC compliance: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for
help.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized
European standards listed under the RE Directive
2014/53/EU, the EMC Directive 2014/30/EU, the
RoHS Directive 2011/65/EU.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific
battery information. The battery is marked with
this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg).
For proper recycling, return the battery to your
supplier or to a designated collection point. For
more information see: www.recyclethis.info
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the
European Union. For proper recycling, return this product to
your local supplier upon the purchase of equivalent new
equipment, or dispose of it at designated collection points. For
more information see: www.recyclethis.info
(1) 이 기기는 가정용으로 전자파적합등록을 한 기기로서
주거지역에서는 물론 모든 지역에서 사용할 수 있습니다.
(2) 당해 무선설비는 전파혼신 가능성이 있으므로
인명안전과 관련된 서비스는 할 수 없음。
Advertisement
