Advertisement
Caution
-
Use, charge and store the appliance at a
temperature between 15°C and 35°C.
-
Only use the adapter supplied to charge the
appliance.
-
If the adapter is damaged, always have it
replaced with one of the original type in order
to avoid a hazard.
-
Do not use an attachment or comb if it
is damaged or broken, as this may cause injury.
-
This appliance is only intended for clipping
human scalp hair, shaving the human beard
line and trimming the human beard, moustache,
sideburns, nose hair, ear hair and eyebrows. Do
not use it for any other purpose.
-
If the appliance is subjected to a major change
in temperature, pressure or humidity, let the
appliance acclimatise for 30 minutes before
you use it.
-
Do not place the beard trimming comb or the
hair clipping comb on the precision attachment.
Compliance with standards
-
This Philips appliance complies with all
standards regarding electromagnetic fields
(EMF). If handled properly and according to the
instructions in this user manual, the appliance
is safe to use based on scientific evidence
available today.
Charging
Charge the appliance fully before you use it for the
first time or after a long period of disuse.
It takes approx. 10 hours to charge the battery
fully. A fully charged appliance has a cordless
operating time of up to 35 minutes. When you
charge the appliance for 3 hours, you can use it for
15 minutes.
The appliance does not run from the mains.
Make sure the appliance is switched off during
charging.
Insert the appliance plug directly into the
1
appliance (Fig. 2).
The charging light on the adapter indicates
,
that the appliance is charging. (Fig. 3)
Optimising the lifetime of the
rechargeable battery
-
Do not leave the appliance connected to the
mains for more than 24 hours.
-
Discharge the battery completely twice a year
by letting the motor run until it stops. Then
fully recharge the battery.
Clipping scalp hair
Preparing for clipping
Only use the appliance on dry scalp hair. Do not
use it on freshly washed scalp hair.
Make sure that the appliance is fully charged.
1
It is not possible to run the appliance from the
mains when the battery is empty.
Make sure that the head of the person whose
2
hair you intend to cut is at the same level as
your chest.
This ensures that all parts of the head are clearly
visible and within easy reach.
Comb the hair in the direction of growth
3
with the barber's comb.
Clipping with hair clipping comb
Put the hair clipping comb on the trimming
1
attachment and push it home ('click') (Fig. 4).
Press the hair length selector and slide
2
the comb to the desired setting (see table
below). (Fig. 5)
The selected setting appears in the window
,
to the left of the hair length selector.
Note: When you clip for the first time, start at the
highest setting (9) to familiarise yourself with the
appliance.
settings of hair clipping comb
Setting
Hair length after clipping
1
2mm
2
4mm
3
6mm
4
8mm
5
10mm
6
12mm
7
14mm
8
16mm
9
18mm
To clip in the most effective way, move the
3
appliance slowly against the direction of hair
growth. (Fig. 6)
-
Do not move the appliance too fast. Make
smooth and gentle movements.
-
Make sure that the flat part of the comb is
always fully in contact with the scalp to obtain
an even result (Fig. 7).
-
Make overlapping passes over the head to
ensure that all hair that should be cut is cut.
-
Pass the appliance slowly over the crown
from different directions to achieve an even
result (Fig. 8).
Regularly remove the comb to blow and/or
4
shake out hair that has accumulated.
You have to adjust the clipping length again after
you have removed the comb.
Contouring without hair clipping comb
Be careful when you clip without comb, because
the appliance removes every hair it touches.
To remove the comb, press the hair length
1
selector (1) and slide the comb upwards (2).
(Fig. 9)
Use the appliance without the hair clipping
2
comb to contour edges.
-
To shape the contours round the ears, tilt the
appliance in such a way that only one edge
of the trimming attachment touches the hair
ends (Fig. 10).
-
To contour the nape hairline, hold
the appliance with the teeth of the trimming
attachment pointing towards the skin. (Fig. 11)
-
To contour the sideburns, hold the appliance
with the teeth of the trimming attachment
pointing towards the skin (Fig. 12).
Trimming
Preparing for trimming
Make sure that the hair is dry and clean.
1
Comb the hair in the direction of growth
2
with the barber's comb.
Beard trimming with comb
Put the beard trimming comb on the
1
trimming attachment and push it home
('click). (Fig. 13)
Press the hair length selector and slide it to
2
the desired setting (see table below). (Fig. 14)
The selected setting appears in the window
,
to the left of the hair length selector.
Note: When you trim for the first time, start at the
highest setting (9) to familiarise yourself with
the appliance.
Note: Using setting 1 with the comb installed results
in a 'stubble look'.
settings of beard trimming comb
Setting
Hair length after trimming
1
2mm
2
4mm
3
6mm
4
8mm
5
10mm
6
12mm
7
14mm
8
16mm
9
18mm
To trim in the most effective way, move the
3
appliance slowly against the direction of hair
growth. (Fig. 15)
Do not move the appliance too fast. Make smooth
and gentle movements and make sure the surface
of the comb always stays in contact with the skin.
Regularly remove the comb to blow and/or
4
shake out hair that has accumulated.
You have to set the trimming length again after
you have removed the comb!
Beard trimming without comb
Trimming without the comb results in a very short
stubble beard.
To remove the comb, press the hair length
1
selector (1) and slide the comb upwards
(2) (Fig. 16).
Never pull at the flexible top of the comb. Always
pull at the bottom part.
Make well-controlled movements and touch
2
your beard only lightly with the trimming
attachment.
Defining beard, moustache and
sideburns
To remove the comb, press the hair length
1
selector (1) and slide the comb upwards
(2) (Fig. 16).
Press the release button (1) and pull the
2
trimming attachment off the appliance
(2). (Fig. 17)
Put the precision attachment on the appliance
3
('click'). (Fig. 18)
Hold the appliance upright when you use the
,
precision attachment. (Fig. 19)
Advertisement
