Download Print this page
Philips CEM210 Quick Start Manual
Philips CEM210 Quick Start Manual

Philips CEM210 Quick Start Manual

Philips car entertainment system quick start guide
Hide thumbs Also See for CEM210:

Advertisement

Quick Links

Register your product and get support at
EN Quick Start Guide
© 2009 Koninklijke Philips Electronics N.V.
All rights reserved.
CEM210_56_QSG_V1.0
CEM210
1
a
b
c
e
f
g
2
3
4
a
c
AMP
b
Overview of parts 1
For cars without ISO connectors
Check and identify the contents of your package:
In-car audio system
Caution
a
Sleeve
b
Be sure to connect the black ground (earth)
Front panel
c
lead first.
ISO connector
d
Trim plate
1
e
Connect the antenna and amplifier as
Rubber cushion
illustrated, if applicable.
f
2
Disassembly tools
g
Cut off the bigger end of the supplied
Screws (4 pieces)
standard connector.
h
3
Check the car's wiring carefully and connect
Connect wires
them to the supplied standard connector.
4
Connect the supplied standard connector to
Caution
the unit.
Ensure that all loose leads are insulated with
1
Green/black strip Left speaker (Rear)
electrical tape.
2
White/black strip Left speaker (Front)
3
Gray/black strip
For cars with ISO connectors
2 3
4
Purple/black strip Right speaker (Rear)
1
Pull out the ISO connectors from car
dashboard and connect them to the bigger
end of the supplied standard connector.
e RED
2
Connect the other end of the supplied
f BLUE
standard connector to the unit.
3
Connect the antenna and amplifier as
illustrated, if applicable. You can connect the
g BLACK
car audio to the amplifier through RCA-TO-
h Orange
RCA cables (not supplied).
i YELLOW To the +12V car battery which is
Connector
Connect to
1
ANTENNA
Antenna
Note
2
REAR LINE OUT R
Rear right speaker
Check wire connection before you mount the
3
REAR LINE OUT L
Rear left speaker
unit into a car.
If preset radio stations are lost when the
ignition key is turned OFF and then back
ON, reconnect the red leads crosswise to the
yellow ones.
5
d
h
a
a
a
b
c
d
a
b
b
b
c
d
e
c
c
f
g
h
i
d
d
Attach the front panel 5
3 4
1
Attach the trim plate.
2
Insert the right side of the panel in the
chassis until it is correctly engaged.
3
Press the left side of the panel and point the
left hole at the left pillar.
4
Release the panel to engage the left side.
Mount in the dashboard 5
1
If the car does not have an on-board drive or
navigation computer, disconnect the negative
terminal of the car battery.
If you disconnect the car battery in a car
that has an on-board drive or navigation
computer, the computer may lose its
memory.
If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
Right speaker (Front)
wires do not touch each other.
2
Remove the two screws on the top of the
unit.
Ignition key +12V DC when ON/
3
Remove the mounting sleeve with the
ACC
supplied disassembly tools.
Motor/electric antenna relay
4
control lead/Amplifier relay
Ensure that car dashboard opening is within
control lead
these measurements:
Ground
5
Install the sleeve into the dashboard and
Illumination switch
bend the tabs outward to fix the sleeve.
6
Place the supplied rubber cushion over the
energized at all times
end of the mounting bolt.
7
Slide the unit into the dashboard until you
hear a click sound.
8
Reconnect the negative terminal of the car
battery.
Turn on
Play audio files
1
1
Press z to turn on the unit.
Press
on the front panel to release the
To turn off the unit, press z for 3
panel.
seconds.
2
Insert a CD with the printed side facing up.
3
Close the panel.
Set clock
Play starts automatically.
»
1
Press MENU/DISP for 3 seconds.
To pause CD play, press 1
2
To resume CD play, press
Press 3 or 4 repeatedly to until the
currently time is displayed.
3
Insert the USB device
Turn z clockwise to set hour.
4
1
Press z to confirm.
Open the cover marked
5
panel.
Turn z anti-clockwise to set minute.
2
6
Insert the USB device into the USB socket.
Press z to confirm.
The unit star ts playing from the USB
»
device automatically.
View clock
1
Press MENU/DISP repeatedly until the clock
is displayed.
Listen to radio
1
Press SOURCE repeatedly to select Radio.
2
Press 3 or 4 to select band: [FM1], [FM2],
[FM3], [AM1], or [AM2] .
3
Press ∞ or § to tune to a radio station
manually.
To search for a radio station
/
automatically, press
for 3 seconds.
.
1
again.
on the front

Advertisement

loading
Need help?

Need help?

Do you have a question about the CEM210 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Philips CEM210

  • Page 1 Connect the antenna and amplifier as illustrated, if applicable. You can connect the car audio to the amplifier through RCA-TO- RCA cables (not supplied). © 2009 Koninklijke Philips Electronics N.V. All rights reserved. CEM210_56_QSG_V1.0 Attach the front panel 5 For cars without ISO connectors Attach the trim plate.
  • Page 2 • 接続されていないすべてのリード線が、絶縁 用テープで絶縁されていることを確認してく ださい。 コネクターがある場合 ダッシュボードから 出し、付属の標準コネクターの大きい方の 端に接続します。 付属の標準コネクターのもう一方の端を機器 に接続します。 必要に応じて、 アンテナとアンプを図に示すよ うに接続します。 カーオーディオとアンプの接 続には、 用します。 © 2009 Koninklijke Philips Electronics N.V. All rights reserved. CEM210_56_QSG_V1.0 コネクターがない場合 前面パネルの取り付け 5 トリムプレートを取り付けます。 注意 パネルの右側を正しくかみ合うまで、シャ • 最初に黒グランド(アース)リード線を接続 ーシに挿入します。 してください。 パネルの左側を押して、 左側の穴が左側のピ ラーを指すようにします。 必要に応じて、アンテナとアンプを図に示...