Page 2
The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Induo shall have no liability for any error or damage of any kind resulting from the use of this document.
Page 3
Induo accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the modem, or for failure of the modem to transmit or receive such data.
Page 4
Indunium 2i User Guide Protecting your modem To ensure error-free usage, please install and operate your modem with care. Do remember the follow: Do not expose the modem to extreme conditions such as high humidity / rain, high temperatures, direct sunlight, caustic / harsh chemicals, dust, or water.
Page 5
Indunium 2i User Guide Regulatory and Type Approval Information Table 1: Directives Directive of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and 2002/95/EC electronic equipment (RoHS)
3.2.16 Debug (Only Available under “Normal Mode”)..............39 Chapter 4. Typical Applications ......................... 41 AT Command Set (Only Available under Normal Mode) ............. 41 4.1.1 Starting Induo Modem Configurator ................. 41 4.1.2 Starting Windows Hyper Terminal..................41 4.1.3 AT Commands Examples....................43 GSM CSD Connection (Only Available under Normal Mode) .............
Page 7
GSM Alphabet ..........................71 Troubleshooting........................... 74 5.5.1 The modem’s LED does not light: ..................74 5.5.2 INDUNIUM 2I keep rebooting all the time:................ 74 5.5.3 No connection with modem through serial link ..............75 5.5.4 Receiving “No Carrier” Message ..................75 Terms and Abbreviations......................
Product
C oncept
1.1
Overview
The Indunium 2i is a rugged GSM/GPRS modem offering state-of-the-art GSM/GPRS connectivity for machine to machine (M2M) applications. The modem transmits data and short messages (SMS) over GSM/GPRS/EDGE mobile networks, also ...
Page 9
Indunium 2i User Guide SMA antenna (adhesive mount antenna with 2.5 m cable) x1 2-pin pluggable terminal block for power connector x1 CD with user guide and configuration utility x1 Note: Please notify your sales representative if any of the above items are missing or damaged.
Indunium 2i User Guide DB9 Male to 9-pin 5mm pluggable terminal block for serial port and DI/DO x1 1.3
Features
a nd
S pecifications
Configuration mode and Normal mode selecting by switch ...
Page 11
Indunium 2i User Guide On: short to GND Dry Contact Off: open Isolation 3K VDC or 2K Vrms Counter Frequency 900 Hz Digital Filtering Time Interval Software selectable Over-voltage Protection 36 VDC Type Sink Mode DO or pulse output Pulse Output Frequency...
Indunium 2i User Guide Chapter
2 . Installation
2.1
Overview
2.2
LED
I ndicators
Name Color Function RSSI (3 LEDs) Green Cellular signal strength level Please refer to Table ME Functions Indicating the working mode.
Indunium 2i User Guide ME Functions NET LED Function ME is in one of the following modes: - POWER DOWN mode - ALARM mode - CHARGE ONLY mode - NON-CYCLIC SLEEP mode - CYCLIC SLEEP mode with no temporary wake-up event in progress...
Indunium 2i User Guide 2.4
Installation
t he
S IM
C ard
Be sure to insert a SIM card before you use the modem. Note: A SIM card set with PIN code cannot be used normally in the modem. You need to use Modem Configurator to unlock the PIN code of the SIM card before using it in the modem.
Indunium 2i User Guide 2.6
Connect
t he
M odem
t o
E xternal
D evice
User can use the serial cable to connect the modem’s DB9 female connector to external controller / computer.
Indunium 2i User Guide Digital Output (Sink Type) 2.8
Grounding
t he
M odem
Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting devices.
Indunium-R Modem Configurator is a PC-based configuration software tool for managing and configuring Induo Indunium 2i modems. With a full graphics mode and Windows-based environment, even first time users will find it easy to learn how to use this new software tool. Indunium-R Modem Configurator can be used to configure the general phone settings and modes, but without needing to look up the appropriate AT commands.
“Modem Configurator” utility are: 1. Green software, no need installation; 2. Full graphics mode, easy to learn how to configure the Indunium 2i modems; 3. The configuration profile can be easily stored, and then replicated to other modems;...
Page 20
Indunium 2i User Guide up the modem. Double click “Modem Configurator.exe” to start the software. Select the correct serial port that is connected to the modem, then click button. After that you can see the popup window “Operation Succeed”. Note: The RS-232 connector uses the standard PINOUT. A direct male DB9 to female DB9 cable can be used to connect to a PC’s serial port.
Page 21
Show the modem’s current firmware and hardware version. Important Notice 1. You must save your parameter changes by clicking “Write” button and then reboot your INDUNIUM 2I by clicking “Reboot” button to take effect for the parameter changes. 2. Debug tab is only available under Normal Mode, other tabs are available under Config Mode.
Indunium 2i User Guide 3.2.2 Export
a nd
I mport
P rofiles
Users could export modem settings from one modem, then import the same settings to other modems, which makes it convenient to carry out “mass deployment” and “pre-configuration”.
Indunium 2i User Guide 3.2.3 Basic
This tab allows user to set follow items: Basic Item Description Default Write down the description name of the modem, such as write Device Name down the modem installation site name in order to identify each Modem modem.
Page 24
A major benefit of GSM technology is that it supports short messages (SMS) for easy communication over the mobile network. Indunium 2i´s proprietary SMS Direct allows you to expand your applications and reduce cost. For example, SMS Direct can be used to update the message on a highway display panel,...
Timestamp Timestamp format is dd.mm.yy hh:mm:ss Set daily limitation for sending SMS in SMS Direct function, when reaching the maximum limitation, INDUNIUM 2I will stop sending SMS any more at that day. 0 is no limitation. Max. SMS/Day Customer could also clear the counter by sending SMS to INDUNIUM 2I with SMS Control privilege, the SMS is “clear sms counter”...
Page 26
Indunium 2i User Guide After enable SMS-IN function, Receive windows will be available, the incoming short messages from specified Caller ID to the modem’s serial port Receive Disable will be displayed in this item. After enable SMS-Out function, Send windows will be available, user could...
Description Default Interval Timeout is the maximum timeout between two packets from serial port. INDUNIUM 2I will process as 2 SMS if the interval between two packets is larger than the value set in the box. Interval The units of the timeout is 100ms, default value is 2, which mean the default packet Timeout timeout is 200ms.
SMS sending time and content is configurable. Note: Only support text format SMS. 3.2.6 Reboot
Since cellular network is not as stable as fixed line, Induo Indunium 2i modems support various auto reboot function to keep modem working 24x7 without hang up. Reboot Note: This function is available under both “Config Mode”...
Page 29
Indunium 2i User Guide incoming call from specified Caller ID (phone number). The Caller ID (phone number) should be specified in “Phone Book” tab by inputting the phone number and tick “Call Reboot” checkbox. Tick the SMS checkbox to allow modem auto reboot with...
Indunium 2i User Guide 3.2.7 Networks
Networks Item Description Default Read SMS Service Service Center from SIM Read the Short Message service center. Center card Show the modem current registration status. There are 3 status: Registration 1. Not registered 2.
Indunium 2i User Guide Note: RSSI should remain higher than 12 to create/accept GSM CSD data calls or establish a GPRS connection. Users can only transmit/receive by SMS (short message) if the RSSI is less than or equal to 11.
Page 32
Indunium 2i User Guide whether it is ON or OFF Event Counter: under event counter mode Null: DI disabled Software filtering is used to control switch bounces. Filtering Input from 0 to 10000ms. Available when DI under Event Counter mode.
Page 33
Indunium 2i User Guide 3.2.10
DO
Type Logic 0 (OFF) Logic 1 (ON) open short This tab describes Digital Output settings. Networks Item Description Default Digital Output acts according to different alarm source. Selected from DI Alarm, SMS Control, Call Control, selection can be one or more.
Page 34
Indunium 2i User Guide Pulse: Generates a square wave as specified in the pulse mode parameters when triggered. Null: Do nothing. Specify the Digital Output status when power on. Null Status When Selected from OFF, ON. Power On OFF: Open.
Indunium 2i User Guide 3.2.11
Modbus
This tab describes Digital Output settings. Networks Item Description Default Enable Tick to enable Modbus RTU Slave function in the modem. Disable Slave ID Modbus slave ID, input from 1 to 247.
Indunium 2i User Guide Address Notification Read only parameters. Function Code The function code for the PLC polling the modem to check (0x02) whether there is new SMS. Have New SMS Read only parameters. (0x01) During polling, when there is new SMS, modem will reply 0x01.
Indunium 2i User Guide Networks Item Description Default Index 1 coil address=0x00 Index Index 2 coil address=0x01 Index n coil address=Index (n-1) coil address + 1 Send out SMS when coil value is 1. On Message Null Input the SMS here. (70 ASIC II char max) Send out SMS when coil value is 0.
Indunium 2i User Guide 3.2.14
Phone
B ook
Networks Item Description Default Phone NO. Input the telephone number. Tick the Call Reboot checkbox to allow modem auto reboot Disable Call Reboot with incoming call from this number.
Indunium 2i User Guide 3.2.15
Phone
G roup
Phone Group is only available for DI, DO, Coil and Register tabs. Select different phone numbers to include them in the same phone group. 38 / 77...
Indunium 2i User Guide 3.2.16
Debug
( Only
A vailable
u nder
“ Normal
M ode”)
In this tab, user could change serial port baud rate in Normal Mode. Please operate according to follow...
Page 41
Indunium 2i User Guide Receive and Send windows Item Description Default “Receive” Display the command replied by the cellular module after windows sending the AT commands “Send” windows Input the AT commands in this windows The same as “Enter” in windows Hypter Terminal, click to enable...
The modem supports the guidelines known as the “AT Command Set.” The AT Command Set is the industry standard line-oriented command language used to communicate with the modem. Note: AT Commands may be entered from terminal software such as Induo Modem Configurator’s Debug Tab or Windows HyperTerminal.
Page 43
Indunium 2i User Guide 3. Select the right COM port (i.e. COM7) and baud rate settings (115200, 8bits, none parity, 1 stop bit, no flow control). 42 / 77...
Indunium 2i User Guide 4. Input AT commands on the HyperTerminal screen (e.g. type “AT” to check the “OK” response from the modem). 4.1.3 AT
C ommands
E xamples
Followings are examples of some AT commands. Please refer to the AT command guide for a full description.
Indunium 2i User Guide 4.2
GSM
C SD
C onnection
( Only
A vailable
u nder
N ormal
M ode)
4.2.1 Overview
A Circuit-Switched Data Connection makes the wireless modem work in a manner similar to a regular analog modem.
Page 46
Indunium 2i User Guide 5. To disconnect the connection, type +++ in Send windows and enable Enter, then click Send. The modem will respond with OK to indicate that you have already switched back to the command mode. 6. Type ATH and then press Enter to disconnect.
Indunium 2i User Guide 4.2.3 Answering
a
C SD
C onnection
1. To answer a call manually, when the Indunium-R Modem Configurator displays the RING response, type to answer a call manually, when the Indunium-R Modem Configurator displays the RING response, type ATA , enable Enter and click Send.
Indunium 2i User Guide 3. To disconnect the modem, type +++. The modem will respond with OK, which means that you have already switched back to command mode. 4. Type ATH and press Enter to disconnect. 4.3
Using
Short
Message
Service
by
Using
AT
Commands
(Only
Available
...
Indunium 2i User Guide 2. Type AT+CMGS=”< phone number >” and then click Send. The terminal will automatically move to the next line, which starts with >. Type your message to the right of the >. 3. Enable Ctrl + Z and click Send to deliver the message.
4.4
Using
S MS
D irect
( Only
A vailable
u nder
C onfig
M ode)
Induo’s proprietary SMS Direct Mode has the following features: 1. Transparently converts serial data to short message or vise versa without using AT Commands.
Page 51
Indunium 2i User Guide The modem provides multi-slot Class 10, which means that there are 4 Rx timeslots plus 1 Tx timeslot, or 3 Rx timeslots plus 2 Tx timeslot. The CS-1 to CS-4 Coding Schemes must be supported by the provider.
Page 52
Indunium 2i User Guide and then click Next. 3. Next, click Standard Modem Types->Standard 19200 bps Modem, then click Next. 4. Select the port you want to install the modem on, we select COM7 here, then click Next. 51 / 77...
Page 53
Indunium 2i User Guide 5. The modem installation is finished, click Finish. 6. At this point, the modem driver should be listed on the “Modems” tab under “Phone and Modem Options.” 52 / 77...
Page 54
Indunium 2i User Guide Modem Diagnostics Follow these steps to verify that the modem is installed properly and has been activated. 1. From the Control Panel, open Phone and Modem Options, click the Modem tab, and then click Properties. 53 / 77...
Page 55
Indunium 2i User Guide 2. Click the Diagnostics tab, and then click Query Modem. 3. If the query is successful, both commands to the modem and responses from the modem will be displayed. 54 / 77...
Page 56
Indunium 2i User Guide Setting up the APN Before using the GPRS on the Windows DUN, the APN (Access Point Name) must be added as a modem initialization command. Detailed instructions are shown below. 1. From the Control Panel, open Phone and Modem Options, click the Modem tab, and then click Properties.
Page 57
Indunium 2i User Guide 3. Enter the following commands in the Extra initialization commands: text box. AT+CGDCONT=1,”IP”,”< APN >” Replace <APN> with the correct service for your account. For example: AT+CGDCONT=1,”IP”,”cmnet” 4. Click OK to close the Properties window. Modify Modem Baud Rate to 115200 bps under Normal Mode 1.
Page 58
Indunium 2i User Guide 2. Click the Modem tab next, select 115200 at Maximum Port Speed then click OK. Adding Windows DUN Follow these steps to add Windows Dial-up Networking. 1. In the Control Panel, open Network Connections, and then click Create a new connection.
Page 59
Indunium 2i User Guide 3. Select the Set up my connection manually option, and then click Next. 4. Select the Connect using a dial-up modem option, and then click Next. 58 / 77...
Page 60
Indunium 2i User Guide 5. Type the name of your service provider in the text input box, and then click Next. 6. Type *99***1# in the Phone number text input box, and then click Next. 59 / 77...
Page 61
Indunium 2i User Guide 7. Type the User name and Password in the appropriate text boxes, and then click Next. 8. Click Finish. 60 / 77...
Page 62
Indunium 2i User Guide 9. Click Dial to establish the connection. 61 / 77...
Note: PIN setting, Phone Book settings and COM settings will not be restored to factory default. 5.3
SMS
C ommands
f or
R emote
C ontrol
INDUNIUM 2I supports remote configuration and remote modem status reading via SMS. An SMS command has following structure: Password:cmd1,a,b,c;cmd2,d,e,f;cmd3,g,h,i;...;cmdn,j,k,n...
Page 64
6. E.g., 1234:1001,INDUNIUM 2I;0004 In this command, password is 1234, and we set device name as “INDUNIUM 2I”, then save parameters and reset the modem to take effect with command 0004.
Page 65
Indunium 2i User Guide 0 - disable pin lock 1 - enable pin lock pin(4 - 8 bytes) flag2: 0 - disable change pin 1 - enable change pin *newPin(4 - 8 bytes and can be null) Set SMS Control...
Page 67
0 - 60s (power on delay turn on module) Set Singal Update cmd,value value: 5 - 1200s Frequency index: 0 - 3(0 - INDUNIUM 2I will auto generate a index when the init string Set Init String cmd,index,content array isn't full) content: max 40 bytes...
Page 69
Indunium 2i User Guide *group: 1 - 10 (phone group) flag: xxxx (binary format: 000 - 111) flag.0 : 0 - disable DI alarm control DO output 1 - enable DI alarm control DO output flag.1: 0 - disable SMS control DO output 1 - enable SMS control DO output flag.2 :...
Page 70
Indunium 2i User Guide return: 1 - comm 2 - comm type 3 - device name Get Base 4 - ME Type Parameters 5 - IMEI 6 - auto CSD 7 - auto delete SMS 8 - sms control passwd...
Indunium 2i User Guide 1 - include in this phone group Get Modbus return: Parameters modbus parameters Get Coil Parameters return: coil parameters Get Register return: register parameters Parameters Get DI Parameters return: DI parameters Get DO Parameters return: DO parameters Note: 1.
Indunium 2i User Guide 5.5
GSM
A lphabet
Standard SMS can contain 160 characters. However, the characters typed must be part of the so-called 7-bit default alphabet as specified by GSM 3.38. You can see in the table below that this alphabet contains all ASCII characters and some accented characters.
Page 73
Indunium 2i User Guide 0×1B14 27 20 CIRCUMFLEX ACCENT 0×1B28 27 40 LEFT CURLY BRACKET 0×1B29 27 41 RIGHT CURLY BRACKET 0×1B2F 27 47 REVERSE SOLIDUS (BACKSLASH) 0×1B3C 27 60 LEFT SQUARE BRACKET 0x1B3D 27 61 TILDE 0x1B3E 27 62 RIGHT SQUARE BRACKET 0×1B40...
Page 74
Indunium 2i User Guide 0×3F QUESTION MARK 0×40 INVERTED EXCLAMATION MARK ¡ 0×41 LATIN CAPITAL LETTER A 0×42 LATIN CAPITAL LETTER B 0×43 LATIN CAPITAL LETTER C 0×44 LATIN CAPITAL LETTER D 0×45 LATIN CAPITAL LETTER E 0×46 LATIN CAPITAL LETTER F 0×47...
à 5.6
Troubleshooting
This section of the document describes possible problems encountered when using the Induo INDUNIUM 2I modem and their solutions. 5.5.1 The
m odem’s
L ED
d oes
n ot
l ight:
...
Indunium 2i User Guide 5.5.3 No
c onnection
w ith
m odem
t hrough
s erial
l ink
Check if the serial cable has been connected properly. Check if the serial cable has been made by following pin assignment given in table PIN Assignment for RS232 and RS485.
Page 77
Indunium 2i User Guide Alternating Current Access Point Name of GPRS Service Provider Network Conformité Européene (European Conformity) CHAP Challenge Handshake Authentication Protocol Circuit Switched Data Clear to Send Decibel Decibel Relative to an Isotropic radiator Direct Current Data Carrier Detect...
Page 78
Indunium 2i User Guide Real Time Clock Request to Send Receive Direction Subscriber Identification Module Subminiature Version A RF Connector Short Message Service TCP/IP Transmission Control Protocol / Internet Protocol Terminal Equipment, also referred to as DTE Transmit Direction UART...