1. Manuals
  2. Brands
  3. CDV Americas Manuals
  4. IP Access Controllers
  5. PROMI 1000
  6. Instructions manual

CDV Americas PROMI 1000 Instructions Manual

Stand alone access control system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Edition 06/2004
This device comes with a varistor.
The varistor must be connected on the strike terminal (electro-
magnet...) operated by the device.
If this product operates more than one strikes, each of them
should have a varistor.
The varistor controls the overload produced by the strike coil –
back emf.
If you are using a « Shear Lock » electromagnetic lock, it is recommended to use a sepa-
rate power supply than the one connected to the PROMI 1000 !
PROMI 1000
STAND ALONE ACCESS CONTROL SYSTEM
G0301FR0222V01

Advertisement

Table of Contents
loading

Summary of Contents for CDV Americas PROMI 1000

  • Page 1 The varistor controls the overload produced by the strike coil – back emf. If you are using a « Shear Lock » electromagnetic lock, it is recommended to use a sepa- rate power supply than the one connected to the PROMI 1000 ! PROMI 1000 STAND ALONE ACCESS CONTROL SYSTEM...

  • Page 2: Table Of Contents

    An synoptic is available at the end of the user manual. The synoptic is usefull to have a general overview on the complete programming instructions. PROMI 1000 USER MANUAL ... 6 ... 6 ... 7 ...

  • Page 3: Presentation Du Produit

    - Printer with or without DTR signal (MTP640 Kyoline printer recommended) - Capability to connect an external reader up to 50 meter - Anti pass back (PROMI 1000 to exit and reader to enter) - 1 relay output RT contact 3A/125V~...

  • Page 4: Factory Default Values

    Edition 10/2003 B. Factory Default Values Operating mode: 0 badge and Pin code Door open time: 1 second Alarm time delay: 00 alarm disabled Key-in keypad time: 10 seconds Master code: 12345 No time zone No Holiday Anti pass back disabled...
  • Page 5 Edition 10/2003 reference: TP50XSE2C RS232 with DTR signal (printer on line) 9600 bauds 1 start 7 bits Parity: even 1 stop IBM mode 40 characters CR = skip line DTR signal: high: printer on line low: printer off line Terminal Paper error: When paper roll is finished, the printer LED flashes fast, The data is stored in the memory buffer of the printer until it is full.

  • Page 6: Programming

    Edition 10/2003 II. PROGRAMMING A. Colors and audible signals The letter in bolt represents the LED color. (O for orange, G for green and R for red) the digit represents the number of beep emitted. The LED turns green and the 1 beep is emitted. The LED turns Red and 1 beep is emitted.

  • Page 7: Menu 01 - Operating Mode

    --- Press * to skip the pin code Another search is launch to select an available user number. ------------------------------------------------------------------------------------------------------------------------- When all the user numbers are full then the PROMI 1000 displays an error. ------------------------------------------------------------------------------------------------------------------------- An error is displayed when a badge has been already programmed...

  • Page 8: Menu 02 - Door Release Time

    Press # go Then press #. back to MENU The PROMI 1000 returns to the main menu The PROMI 1000 returns to the main menu The PROMI 1000 returns to the main menu The PROMI 1000 returns to the main menu...

  • Page 9: Menu 05 - Setting Date And Hour

    Saturday and Sunday --- enter 9 Example: start time 9h30, stop time 22h50, Monday to Friday. Enter 09 30 Press # go Then press#. The PROMI 1000 returns to the main menu back to MENU The PROMI 1000 returns to the main menu 22 50...

  • Page 10: Menu 07 - Holidays

    Press 0 to deactivate the anti pass back mode. Wait 5 seconds for the complete deactivation. Press 1 to activate the anti pass back. The PROMI 1000 must be used as the exit reader and the remote reader as the entry reader.
  • Page 11 At the end of the printing the a message “END PRINTING” appears on the report. The LED lights on in green Press # to go back Then press #. to the Main MENU Press 2 to print the configuration report of the PROMI 1000 control unit. --------------------------START PRINTING--------------------------- Mod 2 Touv 01s Talarm 640s...

  • Page 12: Menu 10 - Badge Enrolment Unit

    Press 0 to select the controller built-in as the badge enrolment reader, press 1 to select the re- mote reader as the badge enrolment reader. Code Username 022DC567 12458 023ABD99 54831 023AA1C0 023A9305 89657 02397F8A 55632 The PROMI 1000 returns to the main menu The PROMI 1000 returns to the main menu ------...

  • Page 13: Menu 11 Delete Schedules

    Press 13 to enter in the setting holiday menu Enter the user number (000 to 999) The LED lights on in red The PROMI 1000 returns to the main menu The PROMI 1000 returns to the main menu The PROMI 1000 returns to the main menu...

  • Page 14: Exit From Programming

    Q. Exit from programming You must be in the main menu to exit from programming, press # Once you exit from programming the PROMI 1000 is on stand-by the LED flashes in orange. III. OPERATING INSTRUCTIONS The key-in time between two digit is set at 10 seconds. Behond that time the data computed is canceled.

  • Page 15: Operating Modes

    --- Mode 0 (badge and Pin code) Present the badge in front of the PROMI 1000 unit. A beep is emitted when the badge is valid. Enter the 5-digit pin code. If the Pin code is valid the relay is activated and the access is granted.

  • Page 16: Event Printing

    Edition 10/2003 After 3 incorrect badge and/or PIN code are entered, the PROMI 1000 reader and the second proximity reader are locked out during 2 minutes and the alarm relay is activated. 2 audible beeps sound when the badge/PIN code are not valid. The LED lights on in red during the time of the lockout.

  • Page 17: Memory

    All the data on the memory G. Anti pass – back To start the anti passback mode go to menu 08. The PROMI 1000 must used as an exit unit and the remote reader as the entry reader. It is important to present the badge on the entry reader and on the exit reader. The access is granted only when the badge was presented on the exit reader.
  • Page 18 IV. PROGRAMMING DIAGRAM Key-in programming time: 2minutes and key-in keypad time: 10 seconds, no schedule no holiday Enter the master code twice The PROMI 1000 will search for the first free user num- Operating mode Press 0 for badge and Pin code...
  • Page 19 15 seconds + press # (press 0 to stop printing report) DTR on press to select the PROMI 1000 reader Delete Schedules: then * twice to delete the holiday Press 1 to grant access Press 0 to deny access...

  • Page 20: Wiring Diagram

    230 V 12VAC/DC Input voltage 230 V 12VAC/DC Input voltage 230 V 12VAC/DC The PROMI 1000 and the remote reader must be separated between each other by 60 cm. Also, if two PROMI 1000 are installed next to each other a...
  • Page 21 N/O contact Common contact N/C contact N/O alarm contact Remote reader red LED Remote reader green LED Request-to-exit input Common of Push button and door contact Alarm input Remote reader data Remote reader buzzer RX printer Common printer DTR signal printer on line...
  • Page 22 User num- Badge Pin Code Username Holiday...

  • Page 23: Template

    VI. TEMPLATE PROMI1000 Wiring access Area 30 x 40 20.5 75.5...

Table of Contents

Save PDF