Download
Share
Print this page
Twinhead Durabook Z141 User Manual
  1. Manuals
  2. Brands
  3. Twinhead Manuals
  4. Server
  5. Durabook Z141
  6. User manual

Twinhead Durabook Z141 User Manual

Raid server
Hide thumbs

Advertisement

Quick Links

Download this manual
P/N: 62+031000+00
© 2021 Twinhead International Corp and/or its affiliates. All rights reserved.
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the Durabook Z141 and is the answer not in the manual?

Questions and answers

Summary of Contents for Twinhead Durabook Z141

  • Page 1 P/N: 62+031000+00 © 2021 Twinhead International Corp and/or its affiliates. All rights reserved.

  • Page 2: Package Contents

    Z14I_RAID Server User Manual Package Contents If any of following items is damaged, please contact your retailer. Adapter Power code Expansion brackets Expansion chassis with Bottom cover RAID transfer bracket Rubber gasket Door brackets IO doors...
  • Page 3 Z14I_RAID Server User Manual RAID Expansion Chassis & SSD Module Screws Screw Name Screw Type Quantity ISOT-M3.0X10L 6 (bumpers) ISOT-M3.0X7L 8 (bumpers) 4 (expansion brackets) 2 (RAID transfer bracket) ISOT-M2.6X4L 14 (bottom cover) 6 (rubber doors) ISOT-M2.6X8L 4 (expansion chassis) &...

  • Page 4: Installation

    Z14I_RAID Server User Manual Installation This section will guide you on how to install the RAID expansion chassis and replace the RAID SSD module. Installing the RAID Expansion Chassis To install the RAID expansion chassis, follow the steps below: 1. Remove the 14 screws securing the bumpers. ISOT-M3.0X10L (marked with orange-white circle): 6 screws...
  • Page 5 Z14I_RAID Server User Manual 3. Pry to remove the mylar from the lower case. 4. By aligning with the screw holes, install the expansion brackets onto their respective slots. NOTE • Ensure that the 4 O-rings ( ) are properly embedded on the upper part of the screw holes (marked with the blue-white circle).
  • Page 6 Z14I_RAID Server User Manual 6. By aligning with the screw holes, install the RAID transfer bracket onto its slot. NOTE • Ensure that the 2 O-rings ( ) are properly embedded on the upper part of the screw holes (marked with the blue-white circle).
  • Page 7 Z14I_RAID Server User Manual 8. Connect the PCIe coaxial cable to the mainboard connector. Then connect the PCIe power cable to the mainboard connector and secure the latch. 9. Route the PCIe power and coaxial cables through the opening on the expansion chassis.
  • Page 8 Z14I_RAID Server User Manual and then fasten the 4 screws to secure the expansion brackets. 10. Attach the 6 screws (ISOT-M2.6X3L) first to secure the expansion chassis to the lower case. Then continue to attach the remaining 4 screws (ISOT-M2.6X8L). ISOT-M2.6X3L (marked with blue-white circle): 6 screws...
  • Page 9 Z14I_RAID Server User Manual NOTE • Ensure that the O-ring is embedded with the ISOT-M2.6X8L screw ( ). 11. Connect the other end of the PCIe coaxial cable to the expansion module board connector. Then connect the other end of the PCIe power cable to the expansion module board connector and secure the latch.
  • Page 10 Z14I_RAID Server User Manual 14. By aligning with the screw holes, install the bottom cover onto the expansion chassis. NOTE • Ensure that the protruding parts of the bottom cover (marked with the red-white frame) are properly positioned with the respective location of the rubber doors.
  • Page 11 Z14I_RAID Server User Manual 15. Attach the 14 screws (ISOT-M2.6X4L) to secure the bottom cover. 16. By aligning with the protruding parts of the bottom cover, install the low-profile rubber doors onto their respective slots on the bottom cover. 17. Place the door brackets onto their respective compartments on the installed rubber doors.
  • Page 12 Z14I_RAID Server User Manual 18. Attach the 6 screws (ISOT-M2.6X4L) to secure the rubber doors. 19. Close the rubber doors.
  • Page 13 Z14I_RAID Server User Manual Replacing the RAID SSD Module To replace the RAID SSD module, follow the steps below: 1. Open the rubber door. 2. Press the latch downwards and pull to remove the RAID SSD module assembly from its compartment. 3.
  • Page 14 Z14I_RAID Server User Manual cover. 4. Remove the RAID SSD module upper cover. 5. Remove the screw (ISOT-M2.0X3L) securing the RAID SSD module. 6. Remove the RAID SSD module.
  • Page 15 Z14I_RAID Server User Manual 7. Install the RAID SSD module. 8. Attach the screw (ISOT-M2.0X3L) to secure the RAID SSD module in place. 9. Replace the RAID SSD module upper cover.
  • Page 16 Z14I_RAID Server User Manual 10. Attach the 4 screws (ISOT-M2.0X3L) to secure the RAID SSD module upper cover. 11. Insert the RAID SSD module assembly into its compartment. Make sure it is firmly seated. 12. Close the rubber door.
  • Page 17 & O RING chassis) 6 (expansion ISOT-M2.6X3L 2.5 ± 0.3 Kgf-cm chassis) 4 (RAID SSD module 2.0 ± 0.3 Kgf-cm upper cover) ISOT-M2.0X3L 1 (SSD module) 2.0 ± 0.3 Kgf-cm Twinhead International Corp. 11F, No.550, Ruiguang Rd., Neihu, Taipei 11492, Taiwan, R.O.C.