1. Manuals
  2. Brands
  3. Logan Manuals
  4. Cables and connectors
  5. SPACE 2000
  6. Operation manual

Logan SPACE 2000 Operation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
LOGAN S.r.l. Strada Panealba,2 - 10040 VOLVERA (TORINO ) ITALY
TEL. (0039).(011). 990.60.60 - ( 4 linee r.a. )
FAX. (0039).(011). 985.90.73
- www.logansrl.it
e-mail
info@logansrl.it
HIGH INTEGRATION
DIGITAL READOUT
Operation Manual
LOGAN S.r.l. Str.da Panealba, 2 10040 VOLVERA (TORINO ) ITALY
TEL. (0039).(011). 990.60.60 - ( 4 lines with a.r. ) FAX. (0039).(011). 985.90.73
www.logansrl.it
e-mail: info@logansrl.it

Advertisement

Table of Contents
loading

Related Manuals for Logan SPACE 2000

Summary of Contents for Logan SPACE 2000

  • Page 1 LOGAN S.r.l. Strada Panealba,2 - 10040 VOLVERA (TORINO ) ITALY TEL. (0039).(011). 990.60.60 - ( 4 linee r.a. ) FAX. (0039).(011). 985.90.73 - www.logansrl.it e-mail info@logansrl.it HIGH INTEGRATION DIGITAL READOUT Operation Manual LOGAN S.r.l. Str.da Panealba, 2 10040 VOLVERA (TORINO ) ITALY TEL.
  • Page 2 SPACE 2000 (T and M versions) OPERATION MANUAL Operation Manual (Code 19.06.3030.01) LOGAN S.r.l. Str.da Panealba, 2 10040 VOLVERA (TORINO ) ITALY TEL. (0039).(011). 990.60.60 - (4 lines with a.r. ) FAX. (0039).(011). 985.90.73 www.logansrl.it e-mail: info@logansrl.it...

  • Page 3: Table Of Contents

    SPACE 2000 (T and M versions) OPERATION MANUAL TABLE OF CONTENTS OPERATING INSTRUCTIONS--------------------------------------------------------------- Overview ----------------------------------------------------------------------------------- Operation panel -------------------------------------------------------------------------- Basic operating functions--------------------------------------------------------------- Power supply connection -------------------------------------------------------------- Origin/tool enabled selection (optional)--------------------------------------------- Simultaneous absolute zero-setting-------------------------------------------------- Absolute pre-selection ------------------------------------------------------------------ Zero-setting and relative pre-selection --------------------------------------------- Absolute - Relative Switching -------------------------------------------------------- Absolute zero memorisation (piece zero) –...

  • Page 4: Operating Instructions

    SPACE 2000 (T and M versions) OPERATION MANUAL OPERATING INSTRUCTIONS Overview In order to clearly understand the operating procedures described in this manual, the meanings of the following terms must be absolutely clear. See the figure below: SPACE 2000 - M version “INCR”...

  • Page 5: Operation Panel

    SPACE 2000 (T and M versions) OPERATION MANUAL Operation panel SPACE 2000 T - SPACE 2000 RIF T version INCH logan 12345.67 INCH 12345.67 TOOL INCH 12345.67 TOOL INCR Axis selection key X Z Z ..Number keys for dimension setting...
  • Page 6 SPACE 2000 (T and M versions) OPERATION MANUAL SPACE 2000 M - SPACE 2000 RIF M version INCH logan 12345.67 INCH 12345.67 INCH 12345.67 INCR Axis selection key X Y Z ..Number keys for dimension setting Decimal point setting key...
  • Page 7 SPACE 2000 (T and M versions) OPERATION MANUAL SPACE 2000 M 4 axis version INCH logan 12345.67 INCH 12345.67 INCH 12345.67 INCH 12345.67 INCR Axis selection key ….. Number keys for dimension setting Decimal point setting key Sign setting key...

  • Page 8: Basic Operating Functions

    Indications on the appropriateness of the function are provided that make perfectly clear how, why and when the respective function can be used. To facilitate learning, the operative functions of the SPACE 2000 are described in the order in which they will most probably be used. Given that many are...
  • Page 9 SPACE 2000 (T and M versions) OPERATION MANUAL The first division line is followed by the necessary conditions that must exist prior to starting the procedure. This part of the description must be given careful attention because in many cases the successful use of a procedure depends on the manoeuvres performed previously.

  • Page 10: Power Supply Connection

    SPACE 2000 (T and M versions) OPERATION MANUAL Power supply connection During this phase, the SPACE 2000 self-diagnostics program runs an internal operating check and then prepares itself for the following operations to be performed by the operator if the outcome is positive.

  • Page 11: Origin/Tool Enabled Selection (Optional)

    10 digital readouts and not just one. Necessary conditions: the SPACE 2000 must be set in position display conditions (“POS” LEDs ON) Select the key : orG= tool=...

  • Page 12: Simultaneous Absolute Zero-Setting

    OPERATION MANUAL INCR Simultaneous absolute zero-setting With this function, the SPACE 2000 permits the absolute zero-setting of all the axes displayed simultaneously. The operator must bring the axes of the machine to the zero point, which we also refer to as the “piece zero” and which all the most important dimensions of the working to be performed refer to.

  • Page 13: Absolute Pre-Selection

    OPERATION MANUAL Absolute pre-selection INCR With this function, the SPACE 2000 permits the entry of an absolute dimension independently for each axis displayed. The entry of an absolute dimension is necessary whenever the operator takes a position whose distance from the “piece zero” is known as a point of reference.

  • Page 14: Zero-Setting And Relative Pre-Selection

    (see “Simultaneous absolute zero-setting” and “Absolute pre-selection”) Necessary conditions: the SPACE 2000 must be set in position display conditions ("POS" LEDs on) Select axis involved A flashing "0"...

  • Page 15: Absolute - Relative Switching

    PIECE ZERO; the opposite passage is made automatically for many functions. The SPACE 2000 shows the absolute dimension display with the ABS LED ON. The display of the relative dimensions refers to the zero set by the latest zero- setting or the relative pre-selection.

  • Page 16: Absolute Zero Memorisation (Piece Zero) - "F1

    MACHINE ZERO (only if the transduction has more than one) the SPACE 2000 must be set in position display conditions ("POS" LEDs on) 3 axes “T” version - the axes summing function must have been disabled with the “F8” function key pag.24 The “F1”...

  • Page 17: Absolute Zero Restoration (Piece Zero) - "F2

    MACHINE ZERO (only if the transduction has more than one) the SPACE 2000 must be set in position display conditions ("POS" LEDs on) 3 axes “T” version the axes summing function must have been disabled with the “F8” function key pag.24 The “F2”...

  • Page 18: Average Point Calculation - "F3

    SPACE 2000 must be set in position display conditions ("POS" LEDs on) The “F3” message Select the function by pressing the...

  • Page 19: Automatic Relative Pre-Set - "F4

    OPERATION MANUAL Automatic relative pre-set With this function, the SPACE 2000 permits the re-selection of the latest relative dimension set with the use of the relative pre-selection command. This function is used to perform working at equidistant steps using the "return to zero"...
  • Page 20 SPACE 2000 (T and M versions) OPERATION MANUAL EXAMPLE M VERSION T VERSION “X”-AXIS MOVEMENT “X” DISPLAY N° OPERATIONS ON THE SPACE 2000 Bring the axis to position “A” PIECE ZERO and then perform absolute INCH zero-setting (pag.14) INCR 0,00 Reach point “B”...

  • Page 21: Millimeter - Inch Conversion - "F5

    If the system is working in inches, the “INCH” LED lights up; otherwise the dimensions displayed are expressed in millimeters. When the SPACE 2000 is switched, it prepares for working in the conditions it was in when switched off. Remember that “F5” function works only on the dimension display and not for the setting of values, which must always be expressed in millimeters.

  • Page 22: Radius - Diameter Switching (Only T Version) - "F7

    OPERATION MANUAL Radius - diameter switching (only T version) This function enabled only in the SPACE 2000 T version switches the display of the X-axis (diametral axis) from radius to diameter and vice-versa. With diameter displayed on the X-axis display, the "DIA" LED lights up.

  • Page 23: Longitudinal Axes Summation Enabling (Only T Version) - "F8

    Axes summation enabling (only for 3-axes T version and 4-axes M version) This function enabled only in the SPACE 2000 3-axes T version switches from independent 3-axes display to 2-axes display, one of which is the summation of two axes.

  • Page 24: Machine Parameter Programming (M.p.)

    This command permits the programming of the machine parameters that define SPACE 2000 functionality. The operations described in this paragraph are usually used during the installation and initial operation of the SPACE 2000 most often conducted by LOGAN technical personnel. Whenever possible, machine parameter programming has already been performed by LOGAN in accordance with the supply specifications: for this reason, the information in this section is provided only for reference.

  • Page 25: Machine Parameter Table

    The table below provides a brief description of each parameter and the respective range of standard values for lathe and milling machine applications. The final column must be filled out by LOGAN Technical Service whenever the application in question requires specific values other than standard.
  • Page 26 SPACE 2000 (T and M versions) OPERATION MANUAL INDEPENDENT PARAMETERS PER AXIS These parameters define the operation of each axis independently and are distinguished from one another by the numerical value of the first digit. M.P. DESCRIPTION VALUES LATHE MILLER SPEC.

  • Page 27: Machine Parameter Description

    With parameter P00, the SPACE 2000 defines whether the application is for a lathe (P00= 0”n”) or a milling machine or boring machine (P00= 1”n”). The value “n” varies from 1 to 4 axes for the Space 2000, and from 1 to 3 axes for the Space 2000 “ RIF”.
  • Page 28 SPACE 2000 (T and M versions) OPERATION MANUAL “P04” START BIT BIT no. PARITY STOP BIT VALUE START 7 BIT DATA ---------- 1 STOP START 7 BIT DATA ---------- 2 STOP START 7 BIT DATA EVEN 1 STOP START 7 BIT DATA...
  • Page 29 SPACE 2000 (T and M versions) OPERATION MANUAL P08 = Zero achieved signal operation mode The zero achieved signal is an optional that requires hardware variations in the main board. The values that can be programmed for this parameter are as follows : The zero achieved signal is enabled by the passage of the display over the “0"...
  • Page 30 With parameter Px0, the SPACE 2000 defines axis disabling with the “0” value and axis enabling with the "1" value. For the X-axis (P10), the SPACE 2000 accepts only the value “1” because this is the axis for dialogue with the user.
  • Page 31 SPACE 2000 (T and M versions) OPERATION MANUAL The pulse sent by the transducer connected to the SPACE 2000 is multiplied by “4” in order to obtain the maximum direct resolution available and is then multiplied by the “Resolution factor”.
  • Page 32 SPACE 2000 (T and M versions) OPERATION MANUAL The possibility to modify the resolution factor in units of tenths of thousandth with respect to the smallest unit of measurement displayed provides the way to make linear correction for any errors that might be present in the tool machine axis.

  • Page 33: Service Messages

    SPACE 2000 (T and M versions) OPERATION MANUAL SERVICE MESSAGES Service messages guide the user in selecting the right operative sequence during the enabling of the SPACE 2000 various commands. N° MESSAGE MEANING “ABS” Indicates the selection of the ABS/INCR key and is used during simultaneous zero-settings or absolute pre-selection.

  • Page 34: Error Messages

    SPACE 2000 (T and M versions) OPERATION MANUAL ERROR MESSAGES Error messages help the user establish the operating limits of the SPACE 2000 or its anomalies. N° MESSAGE MEANING “Par. inc.” A) Indicates the presence of one or more incoherent parameters if displayed when the equipment is switched on;...
  • Page 35 P12-P22-P32. In any case, the internal counters of the SPACE 2000 do not lose the position, and by inverting the movement and returning within the range of values that can be displayed, working can be continued without error.

  • Page 36: Instructions For Repair

    SPACE 2000 (T and M versions) OPERATION MANUAL INSTRUCTIONS FOR REPAIR Contact Technical Assistance Service: LOGAN s.r.l. Str.da PANEALBA, 2 10040 – VOLVERA (TO) ITALY Tel: .+39.011.990.60.60 (4 lines with a.r.) Fax: .+39.011.985.90.73 www.logansrl.it e-mail: info@logansrl.it...

  • Page 37: Declaration Of Conformity

    SPACE 2000 (T and M versions) OPERATION MANUAL EC – D ECLARATION OF CONFORMITY HE MANUFACTURER logan s.r.l. S.da Panealba, 2 10040 VOLVERA (TORINO) ITALY Tel. 011 - 990.60.60 (4 lines with a.r.) Fax 011 - 985.90.73 www.logansrl.it e-mail: info@logansrl.it cap.soc.
  • Page 38 SPACE 2000 (T and M versions) OPERATION MANUAL SPACE 2000 SPEC VERSION OPTIONS SERIAL LINE ZERO ACHIEVED BUFFER BATTERY SERIAL NUMBER SOFTWARE VERSION POWER SUPPLY TRANSDUCER POWER SUPPLY AXES NO. INSPECTION DATE INSPECTOR...

  • Page 39: Notes

    SPACE 2000 (T and M versions) OPERATION MANUAL NOTES...

Table of Contents