Subscribe to Our Youtube Channel
Related Manuals for Emulex OneConnect OCe10102 CNA
Summary of Contents for Emulex OneConnect OCe10102 CNA
- Page 1 OneConnect OCe10102 CNA Installation Manual One Network. One Company. P004450-02A Rev. A Connect with Emulex.
- Page 2 Information furnished by Emulex is believed to be accurate and reliable. However, no responsibility is assumed by Emulex for its use; or for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent, copyright, trade secret or related rights of Emulex.
-
Page 3: Table Of Contents
Installing the Converged Network Adapter ..................2 Viewing the LEDs ..........................7 References ..............................8 Specifications ..........................8 FCC and Regulatory Notices ......................9 Declaration of Conformity ......................10 Laser Safety Notice ........................12 Emulex OneConnect OCe10102 CNA Installation Manual Page iii... -
Page 4: Introduction
Fibre Channel over Ethernet (FCoE) functionality for convergence of Fibre Channel (FC) traffic onto 10 Gigabit EE fabric. Emulex CNAs combine two major functional components: a 10 Gigabit networking MAC and an FC IOC to interface with a unified lossless Ethernet switch. The CNA serves as a common interface for both storage and IP traffic retaining familiar FC and networking software stacks, OS drivers, and management. -
Page 5: Prerequisites
FC industry uses the World Wide Name (wwn) derived from the IEEE address for FC connectivity. If the adapter has two ports, it has two IEEE addresses and two wwns, one for each port. Use the serial number when communicating with Emulex. Record these numbers before installation. - Page 6 6. Observing Electrostatic Discharge (ESD) precautions, store the transceiver in an ESD-safe place. 7. Remove the mounting bracket screws from the top of the CNA. Figure 4 shows the screws that attach the bracket. Figure 4: Removing the Bracket Emulex OneConnect OCe10102 CNA Installation Manual Page 3...
- Page 7 (that is, multimode to multimode). Figure 5 shows the CNA and the optical transceivers. Figure 5: CNA with Optical Transceivers Emulex OneConnect OCe10102 CNA Installation Manual Page 4...
- Page 8 1 meter Direct Attach Note: Some CNA models ship without transceivers for use with Direct Attach Copper cables. CAUTION: Take care not to plug optical cables into cages without transceivers in them. Emulex OneConnect OCe10102 CNA Installation Manual Page 5...
- Page 9 1. Connect the optical cable to the LC connectors on the CNA (see figure 6). Or: Insert the Direct Attach Copper transceiver into the SFP+ cage on the CNA (see figure 7). Figure 6: Connecting Fiber Optic Cable Figure 7: Connecting the Direct Attach Copper cable Emulex OneConnect OCe10102 CNA Installation Manual Page 6...
-
Page 10: Viewing The Leds
LED is summarized below: Activity: (Green) (Ethernet Link) Blink = Activity Off = No activity Link (Amber) On (constantly) = Link up OFF = Link down Figure 8: CNA LED Indicators Emulex OneConnect OCe10102 CNA Installation Manual Page 7... -
Page 11: References
• Taiwan BSMI, Class A • Korea KCC, Class A • RoHS Compliant (Directive 2002/95/EC) • China RoHS compliant Vibration, peak 0.25g (5 Hz to 500 Hz) acceleration (Sweep Rate = 1 octave/min.) Emulex OneConnect OCe10102 CNA Installation Manual Page 8... -
Page 12: Fcc And Regulatory Notices
The reader is cautioned that changes or modifications made to the equipment not expressly approved by Emulex could void the user's authority to operate this equipment. The above statement applies to products marketed in the USA. -
Page 13: Declaration Of Conformity
WARNING: This is a class A product. In a domestic environment, this product may cause radio interference requiring the user to take adequate measures. Note: Changes or modifications not expressly approved by Emulex Corporation could void the user's authority to operate this equipment. - Page 14 Costa Mesa, CA. James M. McCluney, President and Chief Executive Officer European Contact: Emulex Corporation Telephone: 44-118-977-2929 7 & 8 Forest Court Fax: 44-118-977-3237 Oaklands Park Fishponds Road Wokingham, Berkshire RG41 2FD, England Emulex OneConnect OCe10102 CNA Installation Manual Page 11...
-
Page 15: Laser Safety Notice
PCIe expansion slot. In the United States, all optical small form factor transceivers sold by Emulex are certified as Class 1 laser products that conform to the requirements contained in the Department of Health and Human Services (DHHS) regulation 21 CFR subchapter J. - Page 16 Short wavelength and long wavelength small form factor transceivers embedded in Emulex host adapter are non-OFC. For non- OFC links, a compatible laser device must be non-OFC and certified as a Class 1 laser product.
- Page 17 DHHS and European conformity labeling on the small form factor transceiver, and the system level documentation and labeling. Copies of the certificate of conformity for any small form factor transceiver sold by Emulex can be obtained upon request from Emulex Corporation, Costa Mesa.
Need help?
Do you have a question about the OneConnect OCe10102 CNA and is the answer not in the manual?
Questions and answers