Subscribe to Our Youtube Channel
Related Manuals for Moosoo YT-E-005A
Summary of Contents for Moosoo YT-E-005A
- Page 1 HOUSEHOLD ICE MAKER Instruction Manual Model：YT-E-005A/B 110 - 120V 60Hz For any questions and malfunctions of the appliance during use, please contact our customer service email: usa@imoosoo.com...
-
Page 2: Table Of Contents
CONTENT PRODUCT INTRODUCTION OPERATING INSTRUCTIONS CLEANING AND MAINTENANCE TROUBLESHOOTING RECYCLING (DISPOSAL OF THE PRODUCT) -
Page 3: Product Introduction
PRODUCT INTRODUCTION Product feature ■ Fast ice-making Adopting compressor refrigerating technology, ice maker produce bullet shape ice efficiently. ■ Environment protection R134a refrigerants and cyclopentane vesicants are hydrocarbons that do not destroy the ozone layer or increase greenhouse effect. ■ Climate type Usable for SN,N,ST,T types of climate. - Page 4 Ice making space 4-1 Ice maker box(water box) 4-2 Evaporator 4-3 Connecting rod 4-4 Ice shovel plate Storage The storeroom is divided into two parts, the upper part is ice storage area and the lower part is water storage area. 5-1 Ice storage basket 5-2 Water max mark 5-3 Water min mark...
- Page 5 Danger: Do not store or use inflammable articles, such as gas, paint, gasoline, etc. near the ice maker, and do not put inflammable and explosive articles, such as alcohol, gasoline, etc. in the ice maker to prevent explosion and fire. Danger: Do not place the ice maker in a damp, spattered area.
-
Page 6: Operating Instructions
Electrical connection ■ Power supply: The ice maker is powered by alternating current (see product nameplate for specific power supply specifications), and the allowable voltage fluctuation range is ±10%. ■ To ensure safe use, the socket and its connecting wire must be able to withstand more than 10A current. - Page 7 ■ Standby mode － After plugging in the machine, the working indicator light flickers as the machine enters standby mode. － Under ice-making mode, short press the ice-making button, then the working indicator light will stop flickering, and the machine will go into standby mode. ■...
- Page 8 Water injection and drainage ■ Water injection － Water injection is required when the water volume in the storage area is lower than the minimum water level mark. － Add drinking water into the the water storage area. － Each water injection shall keep the water volume between the maximum and minimum water level marks and shall not exceed the maximum water level marks.
-
Page 9: Cleaning And Maintenance
CLEANING AND MAINTENANCE Cleaning ■ Precautions for storage room and external cleaning： － Please unplug the machine before cleaning. － Make sure water does not touch the circuit. － Use a soft towel dipped in warm water or a neutral detergent to scrub the inside and outside surfaces of the ice maker. -
Page 10: Troubleshooting
－ The ambient temperature is too low. Ice cube is too small Ambient temperature is too high or the water temperature is too high. Strange noise When the cooling system is working, the freezing medium flowing in the tube will make noise. When the cooling system is working, the fan will make noise. -
Page 11: Recycling (Disposal Of The Product)
Problem Possible cause Potential solutions The temperature sensor connection wire falls off, Ice full indicator light flashes Contact customer service for breaks or internal short (while you can still make ice ) help circuit There is a continuous reminder Operate according to Kindly Refer to Kindly Reminder that the ice box is not reset Reminder...
Need help?
Do you have a question about the YT-E-005A and is the answer not in the manual?
Questions and answers
My ice maker flashes ice and water at the same time and won't make any ice just keeps doing a cycle of the tray going up and down
The Moosoo YT-E-005A ice maker may be flashing ice and water while not making ice due to the following possible causes:
1. Water shortage – The water reservoir may be empty. Refill it with drinking water.
2. Ice full indicator triggered – The ice storage basket may be full. Remove some ice to allow new ice production.
3. Blocked or malfunctioning sensor – The sensor detecting ice levels or water levels may be dirty or obstructed. Clean the sensor and ensure it is not blocked.
4. Power issues – Ensure the ice maker is properly plugged in and there is no power failure.
If the issue persists after checking these factors, try restarting the machine.
This answer is automatically generated
How do reactivate senor
To reactivate the sensor on the Moosoo YT-E-005A, allow the ice to melt naturally. If the issue persists, check if the temperature sensor connection wire is loose, broken, or has an internal short circuit. If needed, contact customer service for assistance.
This answer is automatically generated
where can you order a plug that drains the water at the back of the machine