pela tools 513137 Manual

pela tools 513137 Manual

Spot welding machine

Advertisement

Available languages

Available languages

Quick Links

Punktsvetstång
Spot Welding Machine
Item No:
513137

Advertisement

Table of Contents
loading

Summary of Contents for pela tools 513137

  • Page 1 Punktsvetstång Spot Welding Machine Item No: 513137...
  • Page 2: Allmänna Säkerhetsföreskrifter

    god funktion. Kontrollera att alla Kontaktinformation maskindelar, är hela och sitter korrekt Verktygsboden Erfilux AB monterade. Källbäcksrydsgatan 1 SE-507 42 Borås • Använd ej en defekt maskin. Lämna in den till Telefon: 033-202650 en auktoriserad serviceverkstad för reparation. Mejl: info@verktygsboden.se •...
  • Page 3 aldrig i närheten av brännbart material. Gnistor kan • VARNING: Var noga med att aldrig beröra övre antända materialet lång tid efter det att arbetet och undre delen av armarna (del #19, #19a) när avslutats. Om brandfara föreligger skall du svetsar på ett arbetsstycke. Låt armananas brandvakt vara utplacerad i minst en timma.
  • Page 4 • För att ansluta den övre armen (del #19) till bra svetspunkt och för att förhindra skador på punktsvetsen , lossar du de fyra skruvarna från armelektroderna. (Se Figur C, D och punktsvetsen (del #15) placerade på ovansidan sprängskissen.) och framsidan av apparaten. (Se Figur A, D, E •...
  • Page 5 • VARNING: Koppla alltid bort punktsvetsen från Problem Åtgärd elnätet innan några åtgärder utförs på den. Ingen svetsning Byt säkring eller återställ • Innan den tas i bruk igen skall man automatsäkring. kontrollera konditionen på punktsvetsen. Kontrollera säkring, återställ Kontrollera strömbrytaren, elkontakten och automatsäkring och kabeln, och eventuell förlängningskabel så...
  • Page 6 Läs igenom följande noggrant. PELA Tools har bifogat listan över delar enbart som referens. PELA Tools ger inte användaren några befogenheter att på egen hand byta ut eller reparera delar på produkten. PELA Tools menar uttryckligen att alla reparationer och byte av delar skall ske av en certifierad reparatör.
  • Page 7 Fig. A Fig. B...
  • Page 8 Fig. C Fig. D...
  • Page 10: Specifications

    Check that all machine parts are Contact intact and correctly installed. PELA Tools Solängsvägen 13 • Do not use a defective machine. Return it to an SE-513 70 Borås authorized service workshop for repair. Phone: 033-202650 E-mail: order@pelatools.com •...
  • Page 11 combustible material. Sparks can ignite the • WARNING: Be careful never to touch the upper material long after the work is completed. If there and lower arms (part # 19, # 19a) when welding is a fire hazard, the fire brigade must be deployed on a workpiece.
  • Page 12: Operation

    front of the appliance. (See Figures A, D, E and the arms and an arc arises between the the exploded view.) surfaces and there is no welding point. To increase the pressure between the arms, • Align the upper arm (part # 19) between the loosen the nut (part # 18).
  • Page 13: Troubleshooting

    • WARNING: Always disconnect the spot welder Troubleshooting from the mains before carrying out any Problem Measure operations on it. No welding Replace fuse or reset circuit • Before using it again, check the condition of the breaker. spot weld. Check the power switch, power plug Check fuse, reset circuit breaker and cable, and any extension cords for and check the power switch.
  • Page 14: Wiring Diagram

    Read the following carefully. PELA Tools has attached the list of parts for reference only. PELA Tools does not give the user any authority to replace or repair parts of the product on their own. PELA Tools explicitly states that all repairs and replacement of parts must be done by a certified repairer.
  • Page 15 Fig. A Fig. B...
  • Page 16 Fig. C Fig. D...
  • Page 17: Eu Declaration Of Conformity

    Declare under our sole responsibility that the product Machine: Spot Welding Machine Type designation: DN-100E Item number: 513137 fulfils all relevant provisions of the 2014/35/EU (LVD). To show compliance with the above Directives the following harmonized standards have been applied: Standards: EN 62135-1:2015 Notified body: TÜV SÜD Product Service GmbH...
  • Page 18 Verktygsboden Erfilux AB Källbäcksrydsgatan 1, SE-507 42 Borås...

Table of Contents