Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Beam GE-PON ONT C504W
Summary of Contents for Beam GE-PON ONT C504W
- Page 1 BEAM GE-PON ONT C504W Installation Guide...
-
Page 2: Key Features
Overview The C504W is a high-speed ONT based on EPON technology for home and the small office. It supports 4 FE, and IEEE 802.11b/g/n interface to the subscriber. It can be connected to PON OLT via a fiber optic cable to provide perfect TPS service. -
Page 3: Contents Of The Package
Contents of the Package User Guide Power Adaptor C504W Precautions Warning Before you install the C504W, read this section. This section contains important safety information you should know before working with the system. Power Considerations Be careful when connecting the system to the supply circuit so that wiring is ... - Page 4 To completely turn off the system, disconnect the power connection to all power supplies. For DC power supplies, locate the circuit breaker on the panel board that services the DC circuit, switch the circuit breaker to the off position, and tape the switch handle of the circuit breaker in the off position.
-
Page 5: Installation
Installation Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. 1. Connect the SC/PC connector on the side of a yellow single-mode optical fiber into the optical terminal of the optical outlet and the other connector into the PON port of C504W by pushing them until you hear a clicking sound. - Page 6 7. Make sure that the PON LED is ON in several seconds or minutes. If PON LED is red, the optical signal is very low, so please contact the carrier. 8. If everything is installed properly, the user can see the DATA LED blink while Internet data is sent/received.
-
Page 7: System Architecture
(Every 1 BEAM Link Down. Optic signal ON Call BEAM sec) Optical signal has been lost Call BEAM ORANGE BEAM Link Up but optical signal is very low Call BEAM No Data transmitting/receiving Call BEAM DATA GREEN BLINK Transmitting/receiving Data... - Page 8 Rear Panel Indication Description PON Interface 1.25G PON Port Wi-Fi Protect Setup RESET Resets the system to factory default. LAN 1~4 FE Ports ON/OFF Power Switch 5.0V 2.0 A Power Terminal Bottom...
-
Page 9: Troubleshooting
Make sure that the optical line is connected properly. Once the optic fiber is connected, the PON LED on the front panel of C504W should be turned on within few seconds. If the PON LED blinks, call BEAM Support to check the optical line connection. -
Page 10: Specification
Specification Item Description Standard IEEE 802.3ah Type Desktop System Architecture Size (mm) 215(W) x 159.5(D) x 43.6(H) Input: 110~220 V ±15%, 60 ± 3Hz Power Output: +5V, 2A (power adaptor used) Consumption: Max 5.0W (typical: 4W) PON interface 1 1.25G 1000Base-PX, 1 Core SMF Available Interface User interface 4 10/100base-Tx (IEEE 802.3u) - Page 11 System Operation and - Support OAM Remote Loop back test. Diagnostic Maintenance - Transmission distance: 10Km or 20Km(Optional) Optical - Transmission quality: BER 10 or lower Physical Characteristics characteristics - Transmission level : -1~ 4dBm Dielectric resistance 100Mohm or higher (based on DC 500V)
- Page 12 Certificate of Installation: (Customer copy) Product Name BEAM GE-PON ONT Model Name C504W Serial No. Date of Installation / 20 (MM/DD/YY) Name Account Number Address Phone E-mail Warranty does not cover damages resulting from accident, misuse or unsuitable operating environment...
- Page 13 Ways to reach BEAM Customer care: 040-66272727 Email: support@beamtele.com http://www.facebook.com/officialbeamfiber Bill Payment Modes: Visit Portal.beamtele.com -> My Account -> Pay bill Pay Online Visit www.beamtele.com -> Bill pay At the e-seva centers Other options Collection executive – Call us @ 66272727...
Need help?
Do you have a question about the GE-PON ONT C504W and is the answer not in the manual?
Questions and answers