Advertisement
3. SPECIFICATION
Model No: ...................................................................SDH90
CO2 Equivalent: ......................................................... 0.0006t
Dehumidifying Capacity: ..................... 90L/day(30°CRH80%)
Freezing Pressure (Max): ...........................................2.5MPa
Global Warming Potential (Rating): ...................................... 3
IP Rating: ........................................................................IP22
Maximum Airfl ow: ...................................................... 500m³/h
Power: ...........1000W ( 27°C RH60%) 1350W(30°C RH80%)
Refrigerant: ........................................................R290/0.30kg
Steaming Pressure (Max): .........................................1.0MPa
Supply: ...........................................................................230V
Working Space: .......................................................90-200m²
Working Temperature: ................................................. 5-35ºC
4. OPERATION
fi g.1
BUTTON
ON/OFF (fi g 1-5)
+
(fig 1-10)
-
(fig 1-11)
Timer (fi g 1-6)
NOTE: Efficiency of the dehumidifier is influenced by the air outside the room. For operating efficiency, try to avoid opening and
closing the windows and doors. For best performance, operate the dehumidifier within the usable operating temperature.
4.1.
OPERATION
4.1.1.
Plug the unit in to the mains socket, a beep will be heard when inserting the plug.
4.1.2.
Press the "ON/OFF" switch and the operation light will illuminate, the humidity display will light to display the previous set humidity.
The initial setting for humidity is 60%, after 3 seconds the display will show the current humidity.
4.1.3.
Press the humidity up or down buttons to adjust to the desired humidity required.
If the required humidity is 3% below the current humidity the unit will start automatically, if the set humidity is 3% more than the current
humidity the dehumidifier will automatically stop.
4.1.4.
When setting the humidity to less than 30%, the unit will run continuously and the display will read "CO".
4.1.5.
To shut the dehumidifier down press the "ON/OFF" switch.
NOTE: If the humidity setting is greater than the current humidity the unit will not run.
WARNING! The fan motor and compressor must run for at least 3 minutes while dehumidifying.
DO NOT start the dehumidifi er immediately after shutting down, allow 3 minutes before restarting.
4.2.
TIMER FUNCTION
4.2.1.
To set Timer for power ON mode, with the unit in power OFF state, press the Timer button (fi g 1-6). The Timer ON LED (fi g 1-1) will
fl icker and the current set time will be displayed. Use the Increase/ Decrease buttons (fi g 1-10, fi g 1-11) to set the required value to
between 0 and 24 hours. After 10 seconds the selected value is set and the Timer ON led will fl icker.
4.2.2.
To set the Timer for power OFF mode, with the unit in power ON state, press the Timer button (fi g 1-6). The Timer OFF LED
(fi g 1-1) will fl icker and the current set time will be displayed. Use the Increase/ Decrease buttons (fi g 1-10, fi g 1-11) to set the
required value to between 0 and 24 hours. After 10 seconds the selected value is set and the Timer OFF led will fl icker.
© Jack Sealey Limited
OPERATION INSTRUCTIONS
Changes between Switch on and Switch off .
Adjust diff erent set values in diff erent states;
1. Increases the humidity value set (RH10% to 95%)
2. Increases the timing (hour) set (00 to 24)
Adjust diff erent set values in diff erent states;
1. Decreases the humidity value set (RH10% to 95%)
2. Decreases the timing(hour) set (00 to 24)
Short press the button to switch a cycle to off .
Set on/off Timer and Exit
Original Language Version
ITEM
OPERATION
1
Timer Indicator
2
Temperature Indicator
3
Dehumidifi cation Indicator
4
Humidity Indicator
5
ON/OFF Control
6
Time Set Control
7
Defrosting Indicator
8
Air Speed Indicator
9
Water Full Indicator
10
Increase Control
11
Decrease Control
SDH90 Issue 1 28/02/22
Advertisement
