1. Manuals
  2. Brands
  3. ESD electronic Manuals
  4. Adapter
  5. PMC-ETH2
  6. Hardware manual

ESD electronic PMC-ETH2 Hardware Manual

2-port fast-ethernet adapter
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
PMC-ETH2
2-Port Fast-Ethernet Adapter
Hardware Manual
PMC-ETH2 Hardware Manual Rev. 1.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PMC-ETH2 and is the answer not in the manual?

Questions and answers

Summary of Contents for ESD electronic PMC-ETH2

  • Page 1 PMC-ETH2 2-Port Fast-Ethernet Adapter Hardware Manual PMC-ETH2 Hardware Manual Rev. 1.0...
  • Page 2 The changes in the document listed below affect changes in the hardware as well as changes in the description of the facts, only. Chapter Changes as compared with previous version First issue Technical details are subject to change without further notice. PMC-ETH2 Hardware Manual Rev. 1.0...
  • Page 3 Vahrenwalder Str. 207 30165 Hannover Germany Phone: +49-511-372 98-0 Fax: +49-511-372 98-68 E-mail: info@esd-electronics.com Internet: www.esd-electronics.com USA / Canada: esd electronics Inc. 12 Elm Street Hatfield, MA 01038-0048 Phone: +1-800-732-8006 Fax: +1-800-732-8093 E-mail: us-sales@esd-electronics.com Internet: www.esd-electronics.us PMC-ETH2 Hardware Manual Rev. 1.0...

  • Page 4: Table Of Contents

    1.1 Description of the PMC-ETH2 Board ........
  • Page 5 This page is intentionally left blank. PMC-ETH2 Hardware Manual Rev. 1.0...

  • Page 6: Overview

    EEPROM Figure 1: Block circuit diagram The PMC-ETH2 is a PMC target board in ‘single’ PCI -Mezzanine Card size. The PCI-to-PCI bridge enables the board to run at 33 MHz and 66 MHz PCI-bus clock rate. The two independent Ethernet interfaces are designed for 10 Mbit/s and 100 Mbit/s networks. The full duplex mode is supported at both speeds.

  • Page 7: Pcb View With Connector Assignment

    Overview 1.2 PCB View with Connector Assignment X900 Ethernet Port 1 X600 Ethernet Port 0 Figure 2: PCB view (PCB side turned to the carrier board) with connector position PMC-ETH2 Hardware Manual Rev. 1.0...

  • Page 8: Summary Of Technical Data

    33 MHz with 3.3 V or 5 V signalling voltage or Signalling voltage 66 MHz with 3.3 V signalling voltage Power supply voltage 3.3 V and 5 V via PCI-Bus Connectors P11, P12 according to IEEE Std. P1386.1-2001 PMC-ETH2 Hardware Manual Rev. 1.0...

  • Page 9: Ethernet Interface

    Physical interface Twisted Pair (IEEE802.3) 10/100BaseT Electrical isolation via repeating coil Connector 8-pin RJ45-socket in the front panel 2.4 Software Support The module runs with standard Ethernet system drivers of Linux and VxWorks. PMC-ETH2 Hardware Manual Rev. 1.0...

  • Page 10: Order Information

    Content: circuit diagrams, PCB top overlay drawing, data V.2086.25 sheets of significant components 1*) If module and manual are ordered together, the manual is free of charge. 2*) This manual is liable to charges, please contact our support. PMC-ETH2 Hardware Manual Rev. 1.0...

  • Page 11: Hardware Installation

    (caution label). 4. Open the case. 5. Remove the carrier board (if already installed) and plug the PMC-ETH2 module carefully on the carrier board. Pay attention that the PMC module is correctly installed on the carrier board. Fix the module with the screws on the carrier board. Use the four M 2.5 x 6 mm screws which are contained in the product package of the module.
  • Page 12 The first Ethernet interface is connected via the RJ45-socket X600 and the second Ethernet interface is connected via the RJ45 socket X900. 11. Connect the computer to mains again (mains connector or safety fuse). 12. Switch on the computer and the peripheral devices. 13. End of hardware installation. PMC-ETH2 Hardware Manual Rev. 1.0...

  • Page 13: Front Panel View With Leds

    Link-Status Ethernet (Link to hub, switch, etc.) Ethernet bit rate: 100 Mbit/s (LED on) Ethernet LED11 (10 Mbit/s, LED off) Port1 LED14 Receive-Status Ethernet (reception of Ethernet data packages) LED13 Transmit-Status Ethernet (transmission of Ethernet data packages ) PMC-ETH2 Hardware Manual Rev. 1.0...

  • Page 14: Connector Assignment

    AD17 FRAME# IRDY# DEVSEL# LOCK# n.c. n.c. V (I/O) AD15 AD12 AD11 AD09 C/BE0# AD06 AD05 AD04 V (I/O) AD03 AD02 AD01 AD00 n.c. Connector type complies with PMC SPECIFICATION IEEE1386.1-2001 n.c..not connected PMC-ETH2 Hardware Manual Rev. 1.0...

  • Page 15: Assignment Of The 64-Pin Pmc Connector P12

    TRDY# +3,3V STOP# PERR# +3,3V SERR# C/BE1# AD14 AD13 M66EN AD10 AD08 +3,3V AD07 n.c. +3,3V n.c. n.c. n.c. n.c. n.c. n.c. +3,3V n.c. Connector type complies with PMC SPECIFICATION IEEE1386.1-2001 n.c..not connected PMC-ETH2 Hardware Manual Rev. 1.0...

  • Page 16: Ethernet 10/100Baset Connection (X600, X900)

    X900 Signal Signal TP010 (TxD+) TP011 (TxD+) TP020 (TxD-) TP021 (TxD-) TP030 (RxD+) TP031 (RxD+) TP040 (CT1) TP041 (CT1) TP050 (CT1) TP051 (CT1) TP060 (RxD-) TP061 (RxD-) TP070 (CT0) TP071 (CT0) TP080 (CT0) TP081 (CT0) PMC-ETH2 Hardware Manual Rev. 1.0...

Table of Contents