Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for MB Connect Line mbNETFIX NFH100
- Page 1 NFH100 k f o r d l i n i o n o n l o a v e r s D o w e r : f r e e a n a g y o u r I X M E T F Q D V m b N...
-
Page 2: Table Of Contents
HW02. This Quick Start Guide provides a quick overview of selected operating procedures and functions of the industrial firewall mbNETFIX NFH100. However, the detailed manual with the important Notes and safety instructions can NOT be replaced by this document. -
Page 3: Safety Instructions
Safety instructions • Only qualified specialist personnel may install, • The router may only be connected to devices, start up, and operate the router. The national which meet the requirements of EN 60950. safety and accident prevention regulations must be observed. •... -
Page 4: Using Open Source Software
Using Open Source Software 3.1 General Information Our products contain, amongst others, so-called open-source software that is provided by third parties and has been published for free public use. The open-source software is subject to special open-source software licenses and the copyright of third parties. Basically, each customer can use the open-source soft-ware freely in compliance with the licensing terms of the respective producers. -
Page 5: Special Liability Regulations
Requests must be directed to the following address, if possible under specification of the serial number: MB connect line GmbH Tel. +49 (0) 98 51 / 58 25 29 0 Fernwartungssysteme Fax +49 (0) 98 51 / 58 25 29 99 Winnettener Str. -
Page 6: Brief Description
Brief description The mbNETFIX is a „self-learning“ easy-to-configure industrial firewall. It can be used in both bridge mode and gateway mode. Bridge mode Gateway mode Network A Network A Network A Network B 0 1 0 192.168.0x/24 192.168.0x/24 192.168.0x/24 172.16.0x/24 The configuration is made via the USB interface using the software mbNETFIX Manager (not included in delivery). -
Page 7: Include In Delivery
Include in delivery Please check that your delivery is complete: 1 x Plug-in bridge Art.-No.: 5.910.010.01.00 1 x mbNETFIX NFH100 1 x cabel USB A - USB-mini B 1 x Quick start-up quide Art.-No.:5.100.200.02.00 Art.-No.: 5.910.000.01.00 Art.-No.: 5.920.000.02.00 Should any of these parts are missing or damaged, please contact the following address:... -
Page 8: Displays, Controls And Connections
Displays, controls and connections 1 x WAN interface 3 x LAN interface 1 x USB slave 2.0 mini – 0V DC connection Power source connection 10 - 30 V DC Functional earth Prog Prog Prog Prog Function Function Digital input (10-30 V DC) (Low 0 –... - Page 9 Designation Status Description Device power source is switched off or device is not connected to power LED off source / power pack. (Power) LED on Power source is connected to terminal block and switched on. After the system has been checked and started, the LED flashes for the flashing duration of the starting up process.
-
Page 10: Getting Started
Getting started Before connecting the device to a network or PC, first ensure that it is properly connected to a power supply, otherwise it may cause damage to other equipment. The mbNETFIX can be operated in two modes (see chapter 4). During the initial commissioning and after each factory reset, the mbNETFIX is always set in Bridge mode, with active packet filter in both directions (Security By Default). - Page 11 Reset Reset Stat Stat a. Bridge mode: Stat Stat 10...30 10...30 After booting, the packet filter is 1. Connect equipotential bonding 10...30 10...30 INACTIVE. to the functional earth (FE). That is, the WAN > LAN and LAN > WAN 2. Connect the terminals transitions are open.
- Page 12 Prog Prog After switching on the Light code in bridge mode Function power supply the - packet filter active - Prog Prog Function LED Pwr lights up. Reset LED Stat on => the firewall is active Stat Stat Reset As soon as the system has LED Usr on =>...
-
Page 13: Using The Mbnetfix In Bridge Mode
Using the mbNETFIX in bridge mode Network A Network A 0 1 0 192.168.0x/24 192.168.0x/24 If you use the mbNETFIX in bridge mode and install it unconfigured in your network environment, start the device in bridge mode with packet filter INACTIVE (input 1 = HIGH). After booting, the packet filter is inactive and the learning mode is active. -
Page 14: Using The Mbnetfix In Gateway Mode
10 Using the mbNETFIX in gateway mode Network A Network B 192.168.0x/24 172.16.0x/24 If you use the mbNETFIX in gateway mode, start the device in Bridge mode with active packet filter. After booting, both the packet filter and the learning mode are active. That is, the WAN >... -
Page 15: Configuration Of The Mbnetfix
11 Configuration of the mbNETFIX The configuration of the firewall is made via the USB interface using the software mbNETFIX Manager (not included in delivery). In addition to a convenient graphical user interface (GUI) and public-key authentication, the „mbNETFIX Manager“ offers all the functions that an automation engineer knows from his PLC programming environment (eg export, import, duplicate, online comparison, online functions, etc.). -
Page 16: Technical Data
(EU) +49 (0) 98 51 / 58 25 29 900 / (US) +1-630-797-6067 MB connect line GmbH Hereby MB connect line acknowledges that the device mbNETFIX NFH100 is in complies with the essential Fernwartungssysteme requirements and other relevant provisions of directive Winnettener Str.
Need help?
Do you have a question about the mbNETFIX NFH100 and is the answer not in the manual?
Questions and answers