Table of Contents Warranty Policies & Claim Procedures Warranty Policies ..............................1-1 Warranty Claim Procedure ............................1-2 Safety Concerns General Safety Guidelines ............................2-1 Water Heater Module ............................... 2-1 Heat Transfer Fluid ..............................2-1 Material Safety Data Sheet ............................2-2 Material Safety Data Sheet ............................
Warranty Policies & Claim Procedures DRYAIR Inc. (referred to within as DRYAIR) warranties its new, unused equipment to be free of defects in material and workmanship at the time of delivery to the first retail purchaser. Warranty Policies Basic warranty policy •...
All warranty credits must be processed with the DRYAIR Warranty Claim Form. • All warranty parts, unless otherwise specified, are to be returned to DRYAIR along with a completed Warranty Claim Form. Note: Prior to returning warranty parts, please call for an authorization number and shipping instructions from the Warranty Department in Canada.
Safety Concerns General Safety Guidelines • Make certain that the operator reads and understands all the information in this manual. • All unauthorized people must be kept away from the equipment when in operation. • Maintain instructional and safety decals. Replace damaged decals. •...
Material Safety Data Sheet BOSS CHILL PG MSDS Canadian Centre for Occupational Health and Safety Issue: 2001-4 (November, 2001) ***MATERIAL SAFETY DATA*** CHEMICAL PRODUCT & COMPANY IDENTIFICATION PRODUCT NAME: ........PROPYLENE GLYCOL INDUSTRIAL PRODUCT CODE: ........70511 EFFECTIVE DATE: ........05/23/03 DATE PRINTED 10/09/03 MSD: 000248 COMPANY IDENTIFICATION: ....
Page 7
ACCIDENTAL RELEASE MEASURE (See Section 15 for Regulatory Information) PROTECT PEOPLE: Isolate area. PROTECT THE ENVIRONMENT: Contain liquid to prevent contamination of soil, surface water or ground water. CLEANUP: For small spills, clean up with absorbent material. Collect material in suitable and properly labeled open containers. For large spills, dike and pump into suitable and properly labeled containers.
Page 8
13. DISPOSAL CONSIDERATION (See Section 15 for Regulatory Information) DISPOSAL: DO NOT DUMP INTO ANY SEWERS, ON THE GROUND OR INTO ANY BODY OF WATER. All disposal methods must be in compliance with all Federal, State/Provincial and local laws and regulations. Regulations may vary in different locations. Waste characterizations and compliance with applicable laws are the responsibility solely of the waste generator.
Material Safety Data Sheet DOWFROST* HEAT TRANSFER FLUID MSDS Canadian Centre for Occupational Health and Safety Issue: 05/09/2002 Received: 09/10/2003 ***MATERIAL SAFETY DATA*** CHEMICAL PRODUCT & COMPANY IDENTIFICATION PRODUCT NAME: ........DOWFROST* HEAT TRANSFER FLUID MSDS#: ............1376 EFFECTIVE DATE: ........05/09/2002 COMPANY IDENTIFICATION: ....
Page 10
ACCIDENTAL RELEASE MEASURE SMALL SPILLS: Absorb with materials such as: cat litter, sawdust, vermiculite, Zorb-all. Collect in suitable and properly labeled containers. LARGE SPILLS: Dike area to contain spill. Recover spilled material if possible. See Section 13, Disposal Considerations for additional information.
Page 11
11. TOXICOLOGICAL INFORMATION ACUTE TOXICITY: Peroral: Rat; female; LD50 = 20300 mg/kg Percutaneous: Based on information for a similar material: Rabbit; LD50 = > 10000 mg/kg DEVELOPMENT TOXICITY: Contains component(s) which did not cause birth defects or any fetal effects in lab animals., The component(s) is/are:, Propylene glycol.
Page 12
STATE/LOCAL Pennsylvania (Worker and Community Right To Know Act): Pennsylvania Hazardous Substances List and/or Pennsylvania Environmental Hazardous Substance List: The following product components are cited in the Pennsylvania Hazardous Substance List and/or the Pennsylvania Environmental Substance List, and are present at levels which require reporting. COMPONENT CAS# AMOUNT...
The HR2250 Hose Reel comes with a 1500 feet hose packages of 3/4” hose (4 hoses x 375’=1500’). The HR2250 Hose Reel is designed • to carry up to 2250 feet so that 5 (5 hoses x 375’=1875’) and 6 (6 hoses x 375’=2250’) hose pachages are also available upon request. Transportation & Storage The reel can be transported by common carrier.
Setup/Operation Danger! It is very important that you read and understand this section before operating the hose reel! Failure to follow the procedures and cautions in this manual could lead to injury or possible death! Manual Controls The Hose Reel has a manual method of controlling the spool rotation “UNLOAD/LOAD” and a general ON/OFF power switch. Caution! When NOT operating the reel, put the reel speed toggle switch (1-1) in the “Off”...
Mechanical Drive Components Access to the internal mechanical drive components is through the access door. This door must be removed. Electric Motor • The electric motor used to drive the reel is manufactured by Marathon Electric. No regular maintenance is required. •...
Page 16
Although the torque limiter clutch is factory set at Dryair, periodic adjustment may be required. It is recommended the torque setting of the clutch be checked twice per season (see “Maintenance” section). With prolonged use, the two friction disks, located on either side of the A-plate sprocket, will eventually show wear.
Maintenance Danger! It is very important that you read and understand this section before operating the hose reel! Failure to follow the procedures and cautions in this manual could lead to injury or possible death! Precautions Electric shock will result in death or serious injury. •...
Electric Motor The electric motor used to drive the reel is a Marathon. • • No regular maintenance is required. Make sure that the motor is not in prolonged contact with moisture during operation • or storage. 5 - Marathon electric motor Gear Box Maintenance &...
• Although the torque limiter clutch is factory (Dryair) set, periodic adjustment may be required. It is recommended tha torque setting of the clutch be checked twice a season. With prolonged use, the two friction disks, located on either side of the A-plate sprocket, will eventually show wear.
Need help?
Do you have a question about the 2250 and is the answer not in the manual?
Questions and answers