Aquatic PRO CLASSIC Quick Start Manual

QUICK START GUIDE
PRO CLASSIC 6.5" SPEAKERS
(PC410)
GETTING STARTED
Make sure your boat, ATV, vehicle, stereo, or amplifier is off during the installation process. Please
read all installation instructions before beginning. If you have any questions, email us at
support@aquaticav.com or use the Aquatic AV App. Customer support on the app is available
Monday through Friday from 8 AM - 5 PM PST.
Contents
When first unpacking your new speaker, please check first that the package contains all the items
below. If something is missing, contact the store where you purchased the product.
One (1) pair of 6.5" Speakers
Grill
Four (4) mounting screws
Four (4) stainless steel speed clips
Tools Needed
Electric drill
Drill bit (sizes will vary based on surface
material)
Phillips screwdriver / Allen wrench
Appropriate saw or utility knife to cut the
surface material
18 AWG or larger speaker wire
Additional Accesories (sold separately)
The Aquatic AV RGB Controller (RG100)
RGB 12 ft Extension Cable (CB105)
RGB 24 ft Extension Cable (CB106)
RGB Y-Splitter (CB111)
Universal Male RGB and Female Speaker Adapter Kit (CB112)
NOTE: For customized installations, additional tools and materials may be needed. Please visit an
authorized Aquatic AV dealer before doing customized installations.
INSTALLATION
Mounting the Speakers
1. Please choose a mounting location with the following mounting considerations in mind.
During the installation of the Speaker, make sure to mount the speaker on a vertical surface. If
mounted on a horizontal surface, water can be let in and deposit around the Speaker. This can
harm the Speaker as time passes.
Make sure to turn off any power connection to the source unit, amplifier, or speakers during the
installation process. Also check that the wires and connections are isolated from each other, not
touching any surface. Otherwise, it can cause a short circuit, which may permanently damage the
equipment and void the Product Warranty.
WWW.AQUATICAV.COM
Quick Start Guide
Warranty information
Template
2.5 mm and 5.2 female speaker spade
connectors (recommended)
Wire strippers (optional)
Crimping tool (optional)
Electric tool (optional)
Marine sealant (optional)
NOTICE
Copyright © Aquatic AV 2021
QUICK START GUIDE
INSTALLATION (cont.)
2. Route the speaker wires (and LED wires, if applicable) from the source to the speaker location
with good clearance for the wires.
Considerations While Wiring Your Speakers
• Speaker wires are not included with the speakers. You should use 18 AWG or larger speaker
wires to connect the speakers to the stereo
• The leads on the speakers are terminated using make spade connectors. You should use
female spade connectors (Not Included) to connect the speaker wire to the speaker leads for
better connection
SPEAKER WIRE COLOR SPEAKER WIRE POLARITY
White
White with a black stripe
3. Trim the template and make sure it fits in the selected location with enough depth and clear-
ance
4. Using a drill bit appropriate for the mounting surface, drill a hole inside the dashed line on the
template to prepare the mounting surface for cutting
5. Using a jigsaw or rotary tool, cut the mounting surface along the inside of the line on the tem-
plate
6. Use a file and sandpaper to refine the size of the cutout if deemed necessary
NOTE: Do not over-tighten the screws, especially if the mounting surface is not flat. Bending the
speaker frame can cause distortion.
Dimensions
4 PIN RGB Connector
Length: 8.3" (210mm)
6.1"
(155.5 mm)
WWW.AQUATICAV.COM
PRO CLASSIC 6.5" SPEAKERS
SPADE CONNECTOR SIZE
Positive (+) 0.2" (5.20 mm)
Negative (-) 0.11" (2.8 mm)
3.4"
6.8"
(86.2 mm)
(174 mm)
2.3"
(58 mm)
5.1"
(130.1 mm)
Copyright © Aquatic AV 2021
(PC410)
5.1"
(130 mm)