Subscribe to Our Youtube Channel
Related Manuals for Orava VS-600
Summary of Contents for Orava VS-600
- Page 1 Electric hair cutter, beard, moustache with integrated suction system VS-600 Instruction manual VS-600...
-
Page 2: Intended Use Of The Device
AC / DC adapter cable connected or with the AC / DC charging cable connected. ORAVA electrical devices are manufactured according to the state of the art and recognized safety rules. Nevertheless, improper and unprofessional use or use contrary to the intended use may result in injury or danger to the life of the user or third party. - Page 3 • Keep the instruction manual as close to the device as possible throughout its service life. Always keep the instruction manual together with the device for future use and use by new users. • Use the device only for the intended purpose and in the manner specified by the manufacturer.
- Page 4 1.3 Electrical safety • Before connecting the device to the power supply for the first time, make sure that the voltage on the device label corresponds to that of the household electrical socked. • The electric device is designed to power from 1/N/PE ~ 230 V 50 Hz. •...
- Page 5 • Do not bend, crush or otherwise expose the power cord of the device to mechanical stress or external heat sources. Damage to the power cord may result in electric shock. • When the power cord is damaged, disconnect the device from the mains and do not use it again.
- Page 6 1.5 Cleaning, maintenance and repairs • Observe the normal user cleaning and maintenance of the device in the recommended way. Do not use solvents or harsh cleaners for cleaning. Pollution and visible stains from finger contact, respectively. The hands can be cleaned using detergent detergents specially designed to clean household devices.
- Page 7 2. Special safety instructions. Read carefully! • The electrical device is designed and manufactured in such a way as to enable safe operation and use by persons without professional qualifications. Despite all the precautions that have been taken by the manufacturer for safe use, operation and use carry some residual risks and associated hazards.
- Page 8 Inspection/Commissioning • We recommend that you perform both initial and follow-up periodic inspections of the device. Use the device only with accessories and spare parts supplied and approved by the manufacturer. • Never use the device if it is incomplete, damaged or damaged during its use (eg falling).
- Page 9 • Always keep the device under supervision during use and operation! • This is not intended to be operated by a programmer, an external timer or remote control, as there is a risk of fire if covered or incorrectly positioned. •...
- Page 10 • Follow the operating and manual instructions for operating the device (operating time / operation and breaks). Clean the device regularly and thoroughly - empty from hair and dirt. Equipment contamination may result in reduced operating parameters and possible consequential damage. •...
- Page 11 Warning! • Never open or disassemble the battery pack. Damage can lead to short circuit and harmful substances. Seek medical advice if affected. • Do not allow the battery to come into contact with fire and do not expose it to direct sunlight or excessive heat.
- Page 12 Operation Device Description: 1. cutting blades 0.5 to 18 mm 2. opening the hair tray 3. tray door 4. On/Off switch 5. adapter light connected 6. connector for battery charging 7. comb attachment 8. cleaning brush 9. AC adapter 10. container with silicone oil 11.
- Page 13 Before use • Make sure the device is clean and functional. Set the comb attachment to the desired length. • Only mount and attach the attachment when the device is switched off! Doing so may cause injury or equipment damage. •...
-
Page 14: Cutting Procedure
Cutting Procedure: Cut the short hair lengths gradually until you cut the final length according to the comb attachment. • Use the comb attachment. • Start cutting with the comb attachment. • Do not force the cutter while cutting. • Hold the cutter gently with the attachment on the cutting head facing up. fig. - Page 15 During cutting or after cutting We recommend that you empty your hair / hair tray after each cut. If you cut your hair, beard, or moustache with long and dense hairs, you may also need to empty the tray during cutting to maintain optimum suction performance. Cleaning and oiling •...
-
Page 16: Technical Specifications
A-sound power level with respect to the reference sound power of 1 pW. Supplied accessories: AC adapter, cleaning brush, comb attachment, oil, comb Subject to change! Producer: ORAVA retail 1, a.s. Seberíniho 2 821 03 Bratislava Slovenská republika Importer: ORAVA retail 1, a.s.
Need help?
Do you have a question about the VS-600 and is the answer not in the manual?
Questions and answers