Table of Contents
Advertisement
Quick Links
Apex Bike Shed Instruction Manual
________________________________________________________________
WARNING
UNPACKING SAFELY
Please follow these instructions to unpack your garden building safely
• Two people minimum to unpack
• Place the pallet on firm level ground
• Cut the plastic banding
• Remove each panel by removing screws one column at a time as indicated below
• Be careful of loose components inside the pack when removing panels
• Check all the components against the checklist prior to install
_______________________________________________________________
BASE KIT AND FIXING PACK
Please note – if you have ordered a base kit it's unlikely you will be able to see the base kit from
the outside of the pack - it will be inside your panels. The fixings are also inside the pack.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Power Apex Bike
Summary of Contents for Power Apex Bike
- Page 1 Apex Bike Shed Instruction Manual ________________________________________________________________ WARNING UNPACKING SAFELY Please follow these instructions to unpack your garden building safely • Two people minimum to unpack • Place the pallet on firm level ground • Cut the plastic banding • Remove each panel by removing screws one column at a time as indicated below •...
- Page 2 Power Apex Bike Shed...
-
Page 3: Table Of Contents
Contents Page 3 – Before You Start Page 4 – Timber & Base Details Page 5 – Components Checklist Page 6 – Pre-Assembly Page 7 – Floor Page 8 - 11 – Walls Page 12 – Gable Tops Page 13 – Roof Page 14 –... -
Page 4: Before You Start
We also strongly advise you to wear safety glasses when installing the felt to protect your eyes. 2 persons recommended Power Sheds Ltd cannot be held responsible for any damage or injury sustained due to incorrect unloading, unpacking, or assembly of any of our products. - Page 5 It is recommended that the floor is at least 25mm above the surrounding ground level to avoid flooding. If you have not chosen to purchase our Power Base, then other suitable bases would include a concrete base (75mm of concrete on top of 75mm of hardcore) or a paving slab base (slabs laid on top of 50mm of sharp sand).
-
Page 6: Components Checklist
Component checklist PAGE 5 OF 18... -
Page 7: Pre-Assembly
• 40mm galvanised nails If you have ordered a Power Base, you will also receive 80mm and 100mm screws. On the rare occasion that not enough screws are provided please contact us and make us aware so we can send more out to yourself. Please be aware we are unable to reimburse if you purchase your own. -
Page 8: Floor
50mm screws. Reminder Ensure bearers are added to the floor! USEFUL TIP! If you have purchased a POWER Base you can screw the floor to the timber POWER base below for maximum strength and security. PAGE 7 OF 18... -
Page 9: Walls
1. Please ensure you have removed the transport blocks as per page 6. 2. Your shed will come with a number of wall sections. The quantity of these will depend which size you ordered. Please see the components table to confirm which panels you should have for your Power Apex Bike Shed. - Page 10 4. Place the 4ft back wall panel and then the other 2ft / 3ft / 4ft end wall panel and again secure using the 50mm screws provided. 5. Attach the one panel which goes at the side of doors (called the door wings). Again, continue to use 50mm screws (three screws per join).
- Page 11 6. Before attaching the other door wing, attach the door sill which looks like a piece of framing in half. This will be screwed to the floor beneath with 35mm screws. We would strongly recommend to pre-drill the holes to avoid splitting. This sill should be 147mm from each end of the floor (but not the floor bearer) and attached to the very outside edge of the floor.
- Page 12 8. Once the two panels are on which go at the side both sides of the doors (door wings), you can add the door head. This is the part which has the ‘Power’ brand on. To secure these to the panels below you need to screw up through the door wings and into the door head.
-
Page 13: Gable Tops
Gable Tops 1. Line up the gable tops with the panels at the front and back. 2. Secure them to the wall panels with 50mm screws from the inside, screwing upwards through the framing. PAGE 12 OF 18... -
Page 14: Roof
Roof 1. Your apex will come with two roof panels. These are not handed so can go on either side and does not matter which direction the tongue and groove of the boards run as it will be covered by the felt and bargeboards. -
Page 15: Doors
Doors 1. Your shed will come with two doors which you will need to hang. The door with the lock on will go on the right (as you look at the shed from the outside) and the door with the shoot bolts will go on the left. 2. -
Page 16: Felt
Felt Health and Safety – Use safety goggles when installing the roofing felt. 1. Roll out the mineral roofing felt along the lower part of one side of the roof. Allow for sufficient overhang to fold down onto the roof bargeboard (but not the underside roof bargeboard). Note –... -
Page 17: Finishing Touches
2. Secure corner strips, which are 58mm wide, at each corner of your Power shed with 40mm nails (at least four per strip). An extra strip is provided to cover the joins between back wall panels. -
Page 18: Aftercare & Maintenance
USEFUL TIP – Looking for some inspiration? Our Instagram has images of hundreds of Power Sheds which have all been sent to us by customers and is a great way to look at the different ways you can build and paint your shed! - Page 19 (4x) board lengths (at either 4ft or 6ft depending what you ordered). Please note: These are 70mm wide and are the same material as the bargeboards. Be careful not to use these during assembly of your Power Shed – These boards are usually taped together. •...
- Page 20 Returns If Power is not for you and you’d like to return your shed within 14 days of delivery then we will collect the item from you without charging a collection fee. No fuss, no fees! All we ask is that you do not unpack the shed or take the shed off the pallet. You will be able to see the shed panels on the pallet if you want to double check the quality of the shed panels.
Need help?
Do you have a question about the Apex Bike and is the answer not in the manual?
Questions and answers