Download Print this page

Launch LTR-03 Quick Start Manual

Rf-sensor

Advertisement

Quick Links

LAUNCH
+86-755-84557891
overseas.service@cnlaunch.com
www.x431.com
LTR-03
RF-Sensor
QuickStartGuide
IMPORTANT: Read these instructions
carefully and use this unit properly before
operating. Failure to do so may cause damage
and/or personal injury and will void the product
warranty.
Safety Instructions
Any maintenance and repair work must be carried out
by trained experts. Failure to do so may result in the
failure of the TPMS sensor. LAUNCH does not
assume any liability in case of faulty or incorrect
installation of the unit.
CAUTION
When mounting/dismounting the wheel, follow
the operation guideline of wheel changer
manufacturer strictly.
Do not race with the vehicle on which the LTR-01
RF sensor is mounted, and always keep the
drive speed under 240km/h.
To guarantee optimal performance, the sensors
may only be installed with original valves and
accessories provided by LAUNCH.
Make sure to program the sensors using
LAUNCH-specific TPMS tool prior to
installation.
Do not install programmed TPMS sensors in
damaged wheels.
After installing the TPMS sensor, test the
vehicle's TPMS following the steps described in
the original manufacturer's user manual to
confirm proper installation.
FCC Warning
Note: Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user's authority to operate the
equipment. This equipment has been tested and
found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment.This
equipment should be installed and operated with
minimum distance 20cm between the radiator &your
body.
Disclaimer of Warranties and
Limitation of Liabilities
All information, illustrations, and specifications in this
manual are based on the latest information available at
the time of publication. The right is reserved to make
changes at any time without notice. We shall not be
liable for any direct, special, incidental, indirect
damages or any economic consequential damages
(including the loss of profits) due to the use of the
document.

Advertisement

loading
Need help?

Need help?

Do you have a question about the LTR-03 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Launch LTR-03

  • Page 1 Failure to do so may result in the Operation is subject to the following two conditions: could void the user's authority to operate the failure of the TPMS sensor. LAUNCH does not (1) This device may not cause harmful interference, equipment. This equipment has been tested and...
  • Page 2 Caution: Always observe LAUNCH to ensure proper sealing. It is mandatory to tire failure. this starting point during the replace the sensor if it is externally damage. Always whole dismounting process.
  • Page 3 首页 制作要求: 原始文件尺寸为:210mmx100mm 纵向对折 制作方式:横向风琴折,折后尺寸为: 70mmx100mm,然后 纵向 对 折, 最终成 品尺寸为70mmx50mm 印刷要求:黑白印刷,采用80g书写纸 对折后最终尺寸为:70mmx50mm...