Advertisement
Quick Links
Advertisement
Summary of Contents for Clack CleanSource
- Page 1 CleanSource Drinking Water System Owner’s and Operator’s Manual ‑ ‑...
- Page 2 INTRODUCTION Thank you for purchasing your new CleanSource Drinking Water System, ® an advanced filtration system combined with state–of–the–art electronic capacity monitoring. Your new system was designed to be a convenient, highly capable countertop water filter for today’s needs. Its integrated meter provides information on filter life.
-
Page 3: Parts List
PaRTs lIsT 1. Filter Housing 2. O-ring 3. UltraCarb Ceramic Filter 4. Faucet 5. Base Assembly 6. Diverter Valve and Tubing Assembly 7. Scouring Pad 8. Adapter and Gasket Kit 9. Battery Door (not shown) 10. Two (2) AAA Batteries Included and Installed (not shown) ‑... - Page 4 PRePaRaTION Unscrew the Filter Housing (item 1) from the Base Assembly (item 5) by holding the base securely and turning the Filter Housing in a counterclockwise direction (Figure 2). Remove the protective packaging from the UltraCarb Ceramic Filter (item 3). IMPORTaNT NOTe: This packaging Figure 2 material must be removed and the filter...
-
Page 5: System Installation
Figure 5 and Gasket Kit (item 8) is provided to obtain a proper fit. Place the CleanSource Drinking Water System on a flat surface near the sink. With the water spout pointing into the sink, turn on the COLD water and divert the water through the filter by turning the Diverter Valve’s white handle 90... - Page 6 15 seconds before using. THe FlOW MeTeR Your CleanSource Drinking Water System features Figure 6 a state-of-the-art water meter to monitor the life of the replaceable UltraCarb Ceramic Filter (Figure 6). When water is flowing through your filter, one...
- Page 7 RePlaCe: The red warning light indicates the filter capacity is exhausted. Replace the UltraCarb Ceramic Filter before continuing to use your system. CleaNING THe UlTRaCaRB CeRaMIC FIlTeR Clean the UltraCarb Ceramic Filter whenever the water flow falls below an acceptable rate. Sanitary precautions should be taken whenever handling soiled components of your filter.
- Page 8 Set filter aside. each time the UltraCarb Ceramic Filter is cleaned or replaced, it is recommended that the Cleansource Drinking Water system is cleaned and sanitized. Fill the Filter Housing with warm soapy water and scrub the inside surface with a soft brush or sponge.
- Page 9 Place the housing and base right side-up with the faucet pointing into the sink. Allow to stand for 15 minutes. After allowing the CleanSource Drinking Water System to stand for 15 minutes, rinse the chlorine solution from the system by turning on the COLD WATER faucet and opening the Diverter Valve to the system.
- Page 10 RePlaCING THe UlTRaCaRB CeRaMIC FIlTeR When the flow meter’s red warning light flashes, replace your old UltraCarb Ceramic Filter with a new filter. Follow steps1, 2 and 3 under “Cleaning the UltraCarb Ceramic Filter.” Discard the used UltraCarb Ceramic Filter. Follow steps 6 through 12 in the CleaNING THe UlTRaCaRB CeRaMIC FIlTeR section.
- Page 11 particles and expel excess air. Make sure the O- ring is properly seated in the filter housing. IMPORTaNT: Each time a new UltraCarb Ceramic Filter is installed you will need to replace the two AAA batteries (Figures 11 & 12). Replacing the batteries will reset the water meter to the original 1,000 gallon and 18 month capacity.
-
Page 12: Warranty
Clack Corporation will repair or replace, at its discretion, any part of the system deemed defective. This warranty does not cover the replaceable batteries or the disposable UltraCarb Ceramic Filter (part number S8068) whose service life depends on feed water conditions.
Need help?
Do you have a question about the CleanSource and is the answer not in the manual?
Questions and answers