Subscribe to Our Youtube Channel
Summary of Contents for VeloFox DM 06
- Page 1 DM06 Display Functionality Introduction Product Name：Color IPS Display Product Model：DM 06 第1 页/共 30页...
- Page 2 1.02 Hangzhou VeloFox Intelligent Technology Co,. Ltd. Ver. Firmware Modification History Version No Reviser Date Revision content V1.01 Leo Liao 2020.12.15 Initial version V1.02 Leo Liao 2021.03.02 1. Add declaration 2. Modify parameter contents 第2 页/共 30页...
- Page 3 Please consult your drive system supplier for additional function requirements and data display. If you have any questions about DM06 functional definition, please consult our sales or technical support team. Our company (VeloFox ®) reserves all the rights to interpret and explain DM06 functional definitions. Hangzhou Velofox Intelligent Technology Co., Ltd...
-
Page 4: Table Of Contents
1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. A. Product Introduction ........................5 1. Product name and model ......................5 2. Product introduction ........................ 5 3. Range of application ........................ 5 4. Appearance and size ........................ 5 5. Display coding rules ......................... 6 B. -
Page 5: Product Introduction
1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. A. Product Introduction 1. Product name and model IPS display of electric power assist bikes Product model：DM06 ⚫ DM06 includes two versions of UART communication and CAN BUS communication DM06_U corresponds to UART communication version；... -
Page 6: Display Coding Rules
1.02 Hangzhou VeloFox Intelligent Technology Co,. Ltd. Ver. size ofφ22.2mm, φ25.4mm, φ31.8mm 14.5 mm 61 mm Holder size ： φ 22.2mm ， φ 25.4mm，φ31.8mm 5. Display coding rules As shown in above picture: Production serial number Manufacture year and week number Manufacture factory code，M0, M1，M2, M3... -
Page 7: Product Manual
1.02 Hangzhou VeloFox Intelligent Technology Co,. Ltd. Ver. Parameter character value（reserved） Parameter character value (wheel size value, 700C=70, 27.5=27) Parameter character value（speed limit information, range from 04 to 46） Parameter character value （voltage，24/36/43/48/52，can be expanded） Customer software version number (may omit) Customer code B. -
Page 8: Installation
② Place remote button on the left side of horizontal tube, using M3*10 hex set to screws and tighten. For more remote button models, please refer to Velofox product catalogue ③ Connect the 5 pin plug to the docking plug of the controller... -
Page 9: Interface
1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. 4. Interface 4.1 Boot interface Boot logo interface is displayed for 3 seconds after the display is turned on. When the communication connection is established, display enters the main interface which shows information obtained from the controller. -
Page 10: Function Interface Introduction
1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. ③ 3.5 inch HD high brightness IPS LCD screen meets the need for customization of the boot interface and UI interface 4.3 Function interface introduction Boot interface and basic function interface Light... -
Page 11: Other Function Interfaces
1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. Other function interfaces Function interface I —— Battery information page Function interface I mainly display battery info, including battery voltage, capacity, changing cycles, and range info. Acumulated changing cycles are provided by battery BMS, if BMS does not provide relevant information, it shows ----. - Page 12 1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. motor will follow data provided by controller, if requested info is not available from controller, display will calculate using collected voltage and electric currents data. * Power output shared between rider and motor requires controller’s support.
- Page 13 1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. user to carry out daily vehicle maintenance. Notification interface can be cancelled by short press M button manually. After connecting to service tool box, the maintenance reminder can be reset through after-sales diagnostic tool, and meanwhile, the maintenance record will be registered.
-
Page 14: Button Definition
1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. Setting interface Within 10s after turning on display, long press M button to enter the setting interface, short press to switch between setting interfaces. Short press to enter parameter picking state. 、... -
Page 15: Definition Of Button Operation
1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. Power- on button Adjust button Function button Power button: Turn on/off the display Adjust button: Adjust the assisting power level during riding and switch functions Long press the adjust buttons to perform specific function operation Function button: Switch interface functions and enter into parameter setting interface 5.2 Definition of button operation... -
Page 16: Assist Level Switch
1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. 6.2 Assist level switch During normal working state，short press buttons to switch assist level, and change assist 、 mode Power assist display modes as shown below： Digital gear: 0-5 levels Short press 、... -
Page 17: Light Control Function
1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. Basic interface Function interfaces 6.4 Light control function Display supports automatic lights-on/off function, when loaded with battery and is turned on, the default is to automatically turn on/off lights, that is the display automatically detects the ambient light intensity and controls the turning on/off of the lights. -
Page 18: Walk Assist Function
1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. 6.6 Walk assist function When speed is 0, long press button to enter walk assist mode, motor outputs power according to the set speed and control the actual walk speed, display shows the walk assist icon and the real-time speed. - Page 19 1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. After battery capacity is lower than 5% or the voltage is lower than low voltage value, display will enter the low-voltage mode. In this mode battery level showed level 0 and border blink at 1Hz, with no power output from the motor, and disabled assist level switch.
-
Page 20: Setting Function
1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. 7. Setting function Display provides specific parameter setting functions. The optional items of setting function will be deleted according to different market and product standards. The following is the complete parameter setting, information reading function description under the default state of display. Please contact our sales and technical support team for confirmation in case of any discrepancies. - Page 21 1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. Imperial Clock SET TIME Customization Default= setting 12：00 Maintenan MAINTENACE Fixed value Default= 5000km reminder Value= Default LEVEL1,backlig Value= Backlight BACK LIGHT ht level 60% LEVEL 3 level Value= LEVEL 2 setting...
-
Page 22: Advanced Setting Function
1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. According Controlle Controller read only r info information communicat ion protocol * Advanced Go to advanced ADVSET=Advanc setting setting secondary advanced ed setting options parameter setting settings interface Reset to RESET Reset... - Page 23 1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. field. The selected password digits will be highlighted with a white background. Short press 、 to edit password value, and short press M button again to confirm the input. The password input interface is as follows：...
- Page 24 1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. Dig-3: PAS= Power Value= Digital 3 gear assistant Mode Dig-3； Power Dig-5； levels assist Dig-5： ICON display Digital 5 gear setting levels ICON： Eng version gears Power PAS= Pedal Value= L1-L5 assist...
- Page 25 1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. Number Default Value= 2-63 of poles value：2 Pulse=assistan for power ce started Step=1 assist Number of pulse magnet starting magnets Current Default CurLtd= current Value= 0- limit Value：12 limitation 31.5A setting Step=0.5A Controller’s...
-
Page 26: Reference Table For The Circumference Value Corresponding To Common Wheel Diameters
1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. Reference table for the circumference value corresponding to common wheel diameters 9. Data clearance Data clearance is aimed at the removal of data information such as subtotal mileage TRIP, average speed, and maximum speed. 10s after display is turned on when display is at function interface, long press M button to show data clearance window, and short press button to select accordingly. -
Page 27: Error Information
1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. After clearance, the subtotal mileage TRIP is 0, average speed, and max speed is 0. ODO information can’t be cleaned manually on the display, professional service tools are required. 10. Error information Display can warn bike faults. -
Page 28: Wire Definition
11.1 Standard wires definition: The standard outlet of the display is in the form of a designated waterproof connector. The standard outlet needs to match the corresponding conversion wire. Velofox has set a corresponding standard for conversion wire length and interface standards. -
Page 29: Standard Conversion Wire Specifications
1.02 Ver. Hangzhou VeloFox Intelligent Technology Co,. Ltd. Table 1 Standard wire definition Adaptor-C2H: 第29 页/共 30页...
Need help?
Do you have a question about the DM 06 and is the answer not in the manual?
Questions and answers