Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Sparky Group HP10 Series
Summary of Contents for Sparky Group HP10 Series
- Page 3 HP10 Series 1-Phase AC EV Charging Station User Manual About this User Manual Read carefully before installation, maintenance and operation! ▷ Failure to read this manual carefully may lead to improper operation. ▷ Failure to follow the safety notes may lead to a danger of death, injury and damage to the device, supplier cannot accept any liability for claims resulting from this.
-
Page 4: Table Of Contents
HP10 Series 1-Phase AC EV Charging Station User Manual CONTENTS 1. ABBREVIATIONS ............................4 2. SAFETY NOTES ............................5 2.1. Safety signs used ............................5 2.2. Environment ..............................6 2.3. Installation ..............................7 2.4. Operation ................................. 7 2.5. Maintenance ..............................8 3. - Page 5 HP10 Series 1-Phase AC EV Charging Station User Manual 6.5. Normally stop charging ..........................26 6.6. Abnormally stop charging .......................... 27 7. FAULT HANDLING AND MAINTENANCE ....................28 7.1. Fault Handling ............................. 28 7.2. Maintenance ..............................30 WARRANTY AGREEMENT ............................ 31 DECLARATION OF CONFORMITY(DOC) ......................
-
Page 6: Abbreviations
HP10 Series 1-Phase AC EV Charging Station User Manual 1. ABBREVIATIONS Abbreviations Description International Electrotechnical Commission Electrical Vehicle, this can be BEV (battery EV) or PHEV (plug-in hybrid EVSE Electric Vehicle Supply Equipment [IEC61851-1] On-board charger (of an EV) Liquid Crystal Display... -
Page 7: Safety Notes
HP10 Series 1-Phase AC EV Charging Station User Manual and connect the shell of the equipment to be protected to the PEN line 2. SAFETY NOTES 2.1. Safety signs used The following warning signs, mandatory signs and information signs are used in this manual, on and in the AC EV Charging station. -
Page 8: Environment
HP10 Series 1-Phase AC EV Charging Station User Manual Indicates important texts, notes or tips. Indicates recycling information. Indicates assemblies or parts that must be disposed of properly. Do not dispose of them in the household waste. 2.2. Environment ▷... -
Page 9: Installation
HP10 Series 1-Phase AC EV Charging Station User Manual 2.3. Installation Safety protection must be done when installing the EV Charging station. ▷ Installation and wiring should be done by personnel with professional qualification, otherwise, hazardous electric shock may result. -
Page 10: Maintenance
HP10 Series 1-Phase AC EV Charging Station User Manual ▷ It is strictly prohibited to use the charging station when the charging adapter or charging cables are defective, cracked, worn, broken or the charging cables is exposed. If you find any, please contact the supplier in time. -
Page 11: Standards Compliance
3.2. Charging connection According to EN IEC 61851-1:2019 , HP10 series products meet the Case C connection. Case C: Connection of an EV to a supply network utilizing a cable and vehicle connector permanently attached to the EV charging station. -
Page 12: Charging Interface
The charging connector of HP10 series products meet IEC 62196-2, Type 2 plug (with charging cable). Fig. 3-2 Type 2 plug on HP10 series products HP10 series products provide a Type 2 female plug with charging cable, it only charging an EV with a Type 2 vehicle inlet. - 10 -... -
Page 13: Product Information
Welcome to use AC EV Charging station produced by our company. The shape & dimensions of AC EV charging station shown as Fig. 4-1. Fig. 4-1 The shape & dimensions of HP10 series The block diagram of AC EV charging station is shown as Fig. 4-2. -
Page 14: Model Number Definition
HP10 Series 1-Phase AC EV Charging Station User Manual 4.2. Model number definition The model number definition of charging station follows the rules as shown in Fig. 4-3. HP10 □ □□ Maximum output rated current 16: 16A; 32: 32A Phase number:... -
Page 15: Mechanical Parameters
HP10 Series 1-Phase AC EV Charging Station User Manual 4.3.2. Functional description Model series HP10 1-phase series Charging Mode Mode 3 Charging Control Remote: “APP-controlled” Local: “Button-controlled” or “Card-controlled” 4 LED lights; Indicator Lights Indicate 4 statuses include standby, charging, fault and network Networking interface WiFi (2.4GHz / 5G Hz), and support OCPP 1.6J Protocol (Optional) -
Page 16: Nameplate
HP10 Series 1-Phase AC EV Charging Station User Manual 4.4. Nameplate On the wallbox shell, there is a nameplate identifying the model and specification of the charging station, the content is shown as Fig. 4-4. Fig. 4-4 The location and content of the nameplate... -
Page 17: Installation
HP10 Series 1-Phase AC EV Charging Station User Manual 5. INSTALLATION 5.1. Unpacking 5.1.1. Packing list Package Quantity AC EV Charging Station 1 pc Empty socket 1 pc RFID card 2 pcs Wall-mounting accessories (including A+B+C+D as Fig. 5-1 shown) -
Page 18: Prepare
HP10 Series 1-Phase AC EV Charging Station User Manual requirements. ▷ If any damage or missing parts are found, please do not start the machine and contact the supplier as soon as possible. ▷ Please keep the packing box and packing materials 1 month for future handling. - Page 19 HP10 Series 1-Phase AC EV Charging Station User Manual Fig. 5-2 Minimum space requirements for wall mounting It is suggested that the charging station should be installed in a place with good ventilation, no direct sunlight and shelter from wind and rain. In order to ensure good ventilation condition, you should mount the charging station vertically and leave enough space.
-
Page 20: Power Supply System
Cross screwdriver Fastening screw 5.3. Power supply system HP10 series products are suitable for installation in TN power supply system. TN-S power supply system wiring mode Fig. 5-3 HP10 work in TN-S system TN-C power supply system wiring mode Earth rod should be installed as far as possible to ensure that household electrical equipment can be effectively protected zero connection. -
Page 21: Installation Steps
HP10 Series 1-Phase AC EV Charging Station User Manual Fig. 5-4 HP10 work in TN-C system with earth rod In TN-C, for local earth rod where there is no condition to install, a series of circuits are set inside HP10 to protect safety. Even if leakage fault occurs when PEN is disconnected or three-phase voltage is unbalanced, HP10 can quickly interrupt charging and protect the personal safety of users. - Page 22 HP10 Series 1-Phase AC EV Charging Station User Manual Drill 4 holes with diameter of 10mm and depth of at least 50mm on the wall with spacing of 143mm × 152mm, and secure the accessories-D to the wall with expansion screws.
-
Page 23: Empty Socket
5.5. Empty socket HP10 series AC EV charging station config a type 2 charging connector. When the charging station is in standby state, please plug the charging connector in the empty connector socket in order to protect the charging connector. Please use expansion screws to fix this empty socket at a suitable position beside the charging station. -
Page 24: Operation
Human-Machine Interface 6.2.1. Overview As shown in Fig. 6-1, HP10 series product is configured with multiple human-machine interfaces. 4 LED lights: Indicate 4 statuses, include standby, charging, fault, and network Swipe card area: Swipe the RFID card to charging Charging control button: Start or stop charging by press for Button-controlled charging Fig. - Page 25 HP10 Series 1-Phase AC EV Charging Station User Manual combinations of indicators are described as below. Indicator Indicator Icon Connotation Color Status Standby status Green Ground fault status Twinkle connected to an EV Charging status BLN control Fault status Yellow...
-
Page 26: Configure Parameters
HP10 Series 1-Phase AC EV Charging Station User Manual Start charging: plug the charging connector into EV socket, press button to start charging. Stop charging: press button again will end the charging, when EV is in charging. 6.3. -
Page 27: Start Charging
HP10 Series 1-Phase AC EV Charging Station User Manual parameters on this page. Fig. 6-5 Set parameters to config the EV charging station After setting, click the “SAVE” button to save the settings, and click the “RESTART” button to restart charging station for settings take effect. Enter your WiFi name and password in the page. -
Page 28: Normally Stop Charging
HP10 Series 1-Phase AC EV Charging Station User Manual Fig. 6-6 Plug into EV socket For the charging control mode of “Card-controlled” or “APP-controlled”, you can control charging process by swipe RFID card or APP after charging connector plug in. -
Page 29: Abnormally Stop Charging
HP10 Series 1-Phase AC EV Charging Station User Manual charging will stop. When the charging is end, please unplug the charging connector and plug back to the empty socket of charging station. 6.6. Abnormally stop charging Forced fault stop: A fault stop initiated by the onboard charger of vehicle. -
Page 30: Fault Handling And Maintenance
HP10 Series 1-Phase AC EV Charging Station User Manual 7. FAULT HANDLING AND MAINTENANCE 7.1. Fault Handling The charging station is automatically protected in the event of the fault. The fault information and handling methods are as follows. LED indicator... - Page 31 HP10 Series 1-Phase AC EV Charging Station User Manual LED indicator Fault code Handling method information Fault code 16: Power off and restart the device. LED flashes: 1×slow, 6×fast Metering fault Check whether the charging connector and its...
-
Page 32: Maintenance
HP10 Series 1-Phase AC EV Charging Station User Manual 7.2. Maintenance To ensure the long-term stable operation of the equipment, please maintain the equipment regularly (usually every month) according to the operating environment. a) The equipment is maintained by professionals. -
Page 33: Warranty Agreement
HP10 Series 1-Phase AC EV Charging Station User Manual WARRANTY AGREEMENT The scope of warranty refers to the product itself. The warranty period is 12 months. During the warranty period, the company will repair the product free of charge in case of failure or damage (determined by the company's technical personnel) under normal use. - Page 34 HP10 Series 1-Phase AC EV Charging Station User Manual We, declare that the construction of the device described in the following complies with the relevant stated below. Relevant EC directives: Directive 2014/53/EU on radio equipment and telecommunications terminal equipment (RED Directive 2014/53/EU).
-
Page 35: Compliance Statement Of Weee
HP10 Series 1-Phase AC EV Charging Station User Manual COMPLIANCE STATEMENT OF WEEE This product cannot be discarded at will when it is abandoned. It must be collected separately for special treatment. - 33 -...
Need help?
Do you have a question about the HP10 Series and is the answer not in the manual?
Questions and answers