PE 1010 MKII User Manual

Belt drive turntable

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Tradition verpflichtet

USER MANUAL

Belt Drive

Turntable

PE 1010 MKII

Table of Contents

Summary of Contents for PE 1010 MKII

Page 1 Tradition verpflichtet USER MANUAL Belt Drive Turntable PE 1010 MKII...
Page 2: Table Of Contents
6. TONE ARM AND PICK-UP CARTRIDGE ........ 9 A.) TRACKING FORCE ............10 B.) ANTI-SKATING ............11 7. OPERATION ..............13 8. TECHNICAL SPECIFICATIONS ..........14 9. SERVICE INFORMATION ........... 16 User manual PE 1010 MKII | © copyright PERPETUUM EBNER 2019...
Page 4: Unpacking
The 3 x 2 silver-colored locking screws must be removed completely before first use (see fig. F 1). For this purpose, please use the enclosed hex key SW3. User manual PE 1010 MKII | © copyright PERPETUUM EBNER 2019...
Page 5: Set-Up And Assembly
F 1 – Undo and remove the locking screws 3. Set-up and assembly Your new Perpetuum Ebner turntable is a sub-chassis turntable and is therefore mostly insensitive to external shocks. F 2 – Assembly of the sub-platter User manual PE 1010 MKII | © copyright PERPETUUM EBNER 2019...
Page 6 (see fig. F 3). F 3 – Assembly of the belt drive on the pulley and the sub-platter Note: If you start the drive of the PE 1010 by turning it on without having placed the platter, it may happen that the drive belt falls off due to the low weight! Next, put the platter on the sub-platter.
Page 7: Connections
(see fig. F 4). F 4 – The connections – power supply, RCA connections and groud connection Ground conn. RCA L + R Power supply User manual PE 1010 MKII | © copyright PERPETUUM EBNER 2019...
Page 8: Drive Settings
This may be necessary after several years because of the decreasing magnetic effect (see fig. F 5 – platter bearing). F 5 – Drive setting – platter bearing Adjusting the sub-chassis drive User manual PE 1010 MKII | © copyright PERPETUUM EBNER 2019...
Page 9: Tone Arm And Pick-Up Cartridge
All settings have already been made at the factory. The weights to balance the tone arm have been removed for transport. Further details can be found in the following chapters. User manual PE 1010 MKII | © copyright PERPETUUM EBNER 2019...
Page 10: A.) Tracking Force
Please be extremely careful in order to not damage the stylus. The recommended tracking force for the supplied device is 18mN (corresponds to a tracking force of 1.8g). User manual PE 1010 MKII | © copyright PERPETUUM EBNER 2019...
Page 11: B.) Anti-Skating
To prevent this, the so- called anti-skating force is applied at the tone arm. At the PE 1010, this was realized by a weight hanging on a thread. The thread of the anti-skating force is guided through an eyelet and hung on a pilot pin on the tone- arm.
Page 13: Operation
We recommend to leave the dust cover open when en- joying music because of so-called microphonic effects, i.e. vibrational stimulation of sound in resonance bodies over the pick-up cartridge. User manual PE 1010 MKII | © copyright PERPETUUM EBNER 2019...
Page 14: Technical Specifications
Moving Magnet (MM) cartridge, ORTOFON 2M • Physical dimensions (width / depth / height): approx. 470 mm x 340 mm x 175 mm (incl. Dust co- ver) • Weight: approx. 12 kg User manual PE 1010 MKII | © copyright PERPETUUM EBNER 2019...
Page 16: Service Information
You will find the addresses on our website: www.perpetuum-ebner.de Subject to technical modifications PERPETUUM EBNER By WE AUDIO SYSTEMS Schrambergerstraße 22 D-78112 St. Georgen im Schwarzwald www.perpetuum-ebner.de User manual PE 1010 MKII | © copyright PERPETUUM EBNER 2019...