PACIFIC CYCLE PRO COMPUTER SW78019-6 Quick Start Manual

19
Please read the entire instruction manual
before using the product and save it for future
reference. We reserve the right for any errors
in text or images and any necessary changes
made to technical data. If you have any questions
regarding technical problems, please contact
our Customer Services.
Product Description
Features
- Clock ( 12/24 Hour)
- Current speed (0~ 150 km/h or 93.2 m/h )
- Average speed (0~ 150 km/h or 93.2 m/h )
- Max. speed (0~ 150 km/h or 93.2 m/h )
- Speed tendency: accelerating or decelerating
- Riding distance / DST ( 0~ 9999.9 km or miles )
- Total riding distance/ ODO (odometer)
- Riding timer/ RTM ( up to 99:59:99 hours)
- Total riding time/ TTM ( up to 9999 hours)
- Approximate calorie burn
- Backlight
Contents
1. Computer
2. Headlebar bracket with cable, sensor
and rubber base.
3. Magnet
4. Battery (2 * Cr2032 , 3V )
5. 4 cable ties
2
1
4
5
4
X
3
Assembly
1.Attach the bracket to the handlebar. Make sure that the
rubber spacer is between the bracket and handlebar and
that the snap buckle is facing the saddle.
2.Run the cable down to
the front fork and secure
it using a cable tie.
3. Attach the sensor to the front
fork and make sure that it is
parallel to the spokes.
Notice: Don't completely tighten
the cable ties straight away.
You might need to adjust the
sensor angle a little after the
magnet has been fitted.
4. Attached the magnet to one of
the spokes.
5. Adjust the magnet and the sensor
so that they face each other, 2~5mm.
6. Twist the computer to right until it
completely into the bracket.
Battery Installation
Insert the battery into the computer and sensor,
making sure that the + is facing upwards.
Computer setup
4
3
2
1
K1
K2
1. Shows Clock, Riding time, Total riding time,
Riding distance,Total riding distance, Calorie
burned, press K1 for data review.
2. Shows current speed.
3. " " appears if speed is above average speed,
" " appears if speed is below average speed.
4. Shows when you start riding, disappears when
you stop riding.
5. Setting: Hold both K1 and K2 buttons for 2~3s,
you can set up time,wheel size, imperial/metric
system, previous total riding distance,riding time.
Press K1 move to next figure, K2 increase the
figures. Please refer to the below chat flows.
Data Clear
Hold K1 and K2 for 3s until the screen display "reset"
Notice: each mode data can only be clear separately.
Speed Clear
Hold K2 for 3s until " MAX, AVG, MPH/KMPH" flash.
Resetting the computer
The computer resets to factory setting if:
-The battery be removed
-Hold both K1 and K2 for 2~3s, resetting.
Power Saving Mode
If the computer is not used or receives
no signals for 5 minutes,it will
automatically enter power saving mode,
the screen will only show current time.
Press any button to
turn the computer back on again.
Sleepping Mode
- If the computer is not used or receives
no signal for 7 days,it will automatically
enter Sleep mode. The screen will only
show " Sleep". Press any button to turn
the computer back on again.
- Hold both K1 and K2 buttons for 6s,
it will enter the sleep mode,Press any
button to turn the computer back on again.
Other Functions:
-3s EL backlight function by pressing K2 button.
Press both K1 and K2 the backlight will keep on.
-The computer low battery warming: When the
Cr2032 coin battery voltage is below 2.5 V the " "
will be displayed. A brand new coin battery should
be replaced.
Wheel size input:
Circumference
Wheel size Wheel size Circumference
of wheel(mm)
diameter diameter if wheel(mm)
20" 1596 ATB 24"*1.75
22" 1759 ATB 26*1.4
24" 1916 ATB 26*1.5
26"(650A) 2073 ATB 26*1.75
26.5"(Tubular) 2117 ATB 26*2(650B)
26.8"(700*25C) 2124 27*1
26.8"(700*28C") 2136 27*1 1/4
27"( 700*32C) 2155
28' (700B") 2237
4
1888
1995
2030
2045
2099
2136
2155