Advertisement
DO NOT get the heater wet or use in areas of high condensation.
8
DO NOT allow the power lead to touch hot surfaces.
8
DO NOT connect the heater to a timer device or other equipment than can automatically switch the heater on or off.
8
If an extension cable is required it must be of the same cross section as the heater cable. It must be as short as possible and fully
9
unwound.
DO NOT connect other appliances to the same mains socket as the heater.
8
DO NOT operate the heater when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT stand on the heater.
8
DO NOT use the heater with wet hands or when there is water on the power cord.
8
Ensure that the heater is correctly turned off when not in use and store in a safe, dry, childproof location.
9
DO NOT use the heater for anything other than its intended purpose. It is designed to provide heat in enclosed areas larger than 4m³,
8
such as workshops and other industrial areas. It is not suitable for drying clothes or laundry.
NOTE: Children of less than 3 years should be kept away unless supervised continuously.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended
normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand
the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user
maintenance.
CAUTION: Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and
vulnerable people are present.
NOTE: This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children
without supervision.
2. INTRODUCTION
Electric fan heater for industrial applications. Features two heat settings and adjustable thermostat control with fan only option. Auto cooling
system to prevent unit from overheating during use. A totally dry heat with no condensation, no gas, no fumes and no smell. Ideal for workshops
and garages. Supply: 415V/3ph - 63A. Supplied with 3-phase chassis mounted 5-pin connector (extension cable required).
3. SPECIFICATION
Model No: .............................................................. EH30001
Power: ............................................................ 15000/30000W
Output ..............................................................102,500Btu/hr
Supply: ............................................................ 415V/3ph-63A
Heated area: ................................................................ 600m
IMPORTANT!
This unit is designed to raise the ambient temperature of an entire room, the temperature of the air coming out of the front of the heater will be
warmer than the general temperature of the room, but there may not be a significant increase owing to the large volume of air passing over the
element. For the same reason, the element is hot during operation, but does not glow. The room temperature depends on room size, insulation
and the ambient temperature, which will increase as the room gets warmer.
fig.1
4. ASSEMBLY
4.1.
ASSEMBLY OF THE LEGS. (Ref. fig.1)
4.1.1.
On either side of the heater body there are two threaded inserts (B) for mounting the 'V' shaped leg frames (A). Note that the axle hole
at the shorter end of the 'V' frames should be orientated towards the back of the heater.
4.1.2.
Take two M8 x 40mm bolts (D) and slide a plain washer (C) onto each one. Insert a bolt through each of the mounting holes on the leg
frame and slide a split washer (E) over each protruding bolt. Align the bolts with the two threaded inserts (B) on the heater body and
screw them down securely.
4.1.3.
Mount the other 'V' frame to the other side of the heater body in the same way.
4.2.
ASSEMBLY OF THE WHEELS. (Ref. fig.2)
4.2.1.
Take the axle rod (F) and insert it through the holes in the 'V' frames so that the threaded rod ends protrude equally either side. Retain
the axle rod in this position by inserting split pins (G) through the holes situated just on the inside of each leg frame.
4.2.2.
Slide a plain washer (H) over each end of the axle rod, followed by a wheel (J) followed by anther plain washer (H).
4.2.3.
Screw a nyloc nut (L) onto each end of the axle by hand until it begins to bite. Hold one nut steady with a 19mm spanner and
progressively tighten each nut until it bottoms out on the thread.
© Jack Sealey Limited
3
fig.2
Original Language Version
fig.3
EH30001 Issue 7 12/10/21
Advertisement
