Page 1
Colour Television 28DN2F Service Manual Model C28ER56NF (FRANCE) Service Ref. No. C28ER56NF-01 PRODUCT CODE: 1113 27210 ORIGINAL VERSION: Chassis No. EB4-A Note This TV receiver will not work properly in foreign countries where the television transmission system and power source differ from the design specifications.
SAFETY PRECAUTION 1: An isolation transformer should be connected in the 3: When replacing a chassis in the cabinet, always be power line between the receiver and the AC line when certain that all the protective devices are installed a service is performed on the primary of the converter properly, such as, control knobs, adjustment covers or transformer of the set.
CIRCUIT DESCRIPTION 1. POWER SUPPLY control) The chroma signal is divided into R-Y and B-Y The power supply circuit of the EB4-A chassis is chroma signals, demodulated in IC201, and output from composed of a rectifier smoothing circuit, an oscillation pin30 (R-Y) and pin31 (B-Y).
6. HORIZONTAL OUTPUT Pin25: Black A horizontal oscillation signal is output from pin37 of Pin26: IREF IC201 and switches the drive transistor Q431. This Pin27: Odd/Even output switching signal is current amplified by the drive Pin28: GND transformer T431 and drives the output transistor Q432. Pin29: - When Q432 becomes ON, an amplifying current flows Pin30: V-deflection stop output...
SERVICE CONTROL ADJUSTMENT VIF DET 1/2 AFT ADJ. B1 POWER SUPPLY ADJ. TU-AGC ADJ. MAIN BOARD HIGH VOLTAGE & H-WIDTH ADJ. FOCUS ADJ. V-CENTRE ADJ. V-SIZE ADJ. H-CENTRE ADJ. GREY SCALE ADJ. SIF ADJ.(FM Det-2) SIF BOARD SIF ADJ.(FM Det-1) T3852 T3851 T3853...
Page 7
B1 POWER SUPPLY ADJUSTMENT HIGH VOLTAGE & WIDTH ADJUSTMENT 1. Set VR641 to be mechanically centre before [HIGH VOLTAGE ADJUSTMENT] pressing the mains ON/OFF switch. 1. Tune the receiver to the circular pattern. 2. Tune the receiver to a PAL circular pattern. 2.
CIRCUIT ALIGNMENT 10kΩ 0.002µF 103P 0.01uF 75Ω 1kΩ Jig-A Output probe Input probe VIF alignment (DETECTOR ADJ.1) Adjustment SETTING Waveform Notes How to select SYSTEM L or DC 15.0V IC651-pin1 By using T141, L’. AGC voltage (4.3-4.5V) IC201-pin48 adjust "P" to be Output probe (Side b) IC201-pin45 maximum...
Page 9
SIF alignment (FM Detector-2) SETTING Adjustment DC 12V K38H2-pin3 By using T3852, adjust DC DC5V IC3851-pin21 level to be 1.7V. Output probe IC3851-pin15 Input probe IC3851-pin16 Scope 100mV/div Carrier Frequency 5.5MHz Modulation Frequency 1KHz (Sine wave) System SETTING Adjustment DC 12V K38H2-pin3 By using T3851, adjust DC DC5V...
Page 10
INITIALISATION (Important Notice) When you replace a memory IC (IC802), it is 2. Select the desired service item by using the Function necessary to initialise the IC as following step. button on the remote control handset. 3. Change the data by using the Level + or - button A.
CHASSIS ELECTRICAL PARTS LIST Product safety should be considered when a component replacement is made in any area of a receiver. Components indicated by a ! mark in this parts list and the circuit diagram show components whose value have special significance to product safety.
Page 13
Description Ref. No. Part No. Ref. No. Part No. Description RESISTOR C3851 403 069 9500 CERAMIC 0.01U Z R2601 401 018 2800 CARBON 330 JA 1/4W C3852 403 069 9500 CERAMIC 0.01U Z R2602 401 019 1901 CARBON 3.9K JA 1/4W C3853 403 069 9500...
Page 14
Ref. No. Part No. Description Part No. Description Ref. No. 610 264 1479 C3465 403 018 7403 CERAMIC 220P J C3466 403 069 9500 CERAMIC 0.01U Z ASSY,PWB,AUDIO F3SL 1AA0B10E3250B C3467 403 041 8804 ELECT 10U M C3468 403 069 9500 CERAMIC 0.01U Z TRANSISTOR...
Page 15
Description Ref. No. Part No. Ref. No. Part No. Description R3479 401 038 3603 MT-GLAZE 3.3K JA 1/10W 405 019 1909 TR 2SC536-E-NP R3480 401 038 3603 MT-GLAZE 3.3K JA 1/10W 405 019 2708 TR 2SC536-F-NP R3481 401 038 0701 MT-GLAZE 2.2K JA 1/10W 405 019 3804...
Page 23
Description Ref. No. Part No. Ref. No. Part No. Description -23-...
Page 24
Some voltages may vary with sulla massa del chassis, i valori di voltag- lare importanza per il sicuro funziona- ficato altrimenti. 28DN2F/C28ER56NF cance to product safety. It is particu- Number: signal strength. gio presi usando un segnale di barre col- Il transistore 2SA608(E,F) puo essere mento del TV.