Advertisement
Quick Links
BMW OBDII Key programmer ADVANCED
Now works with K-Line and D-CAN bus
BMW OBD Key programmer ADVANCED is designed to program new original
key or PCF7936 chip.
Key programming takes only 10-15 seconds (for CAS sw. versions before
ISTA-P-41) and only 8-11 minutes for CAS with new firmware (sw. version ISTA-
P-41 and higher).
Newer sw. version CAS (ISTA-P-41 and up) will only take longer time the first
time you program the key. If you ever programmed this car – all next attempts
will be fast within 10 seconds.
Also, the device turns off the factory security alarm (for the time of
programming) and erases the memory of diagnostic faults via OBDII.
The ADVANCED kit also includes the HT Pro device and two HTspy keys for
BMW and MINI Cooper.
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Advanced BMW OBDII
- Page 1 Also, the device turns off the factory security alarm (for the time of programming) and erases the memory of diagnostic faults via OBDII. The ADVANCED kit also includes the HT Pro device and two HTspy keys for BMW and MINI Cooper.
-
Page 2: Supported Models
Supported models (11/2006 — 10/2013) BMW 1' E88 (11/2006 — 10/2013) BMW 1' E82 (02/2004 — 08/2008) BMW 3' E90 (07/2007 — 12/2011) BMW 3' E90 LCI (02/2004 — 08/2008) BMW 3' E91 (07/2007 — 05/2012) BMW 3' E91 LCI (05/2005 —... -
Page 3: Device Description
Device description... - Page 4 The programmer has two diodes D, K, Ready and a sound buzzer. LED features: D LED indicates diagnostic status. K LED shows the status of the data for key generation. Ready LED after establishing communication with the car. Light is D - flashes green always on:...
- Page 5 Alarm disabling If your security alarm is off or you do not have security alarm at all then you do not need to do these operations. You can continue to the key programming procedures. Make sure that the option switch is switched to the "Alarm Off" position. Make sure that the car battery status shows 11 or higher voltage.
-
Page 6: Key Programming
Key programming The car should not be in sleep mode! The car’s START/STOP button light should be on, if not - press START/STOP button or press the central locking button (for the old E60). Make sure that the option switch is switched to the "Key Programming" position. - Page 7 Key programming A) If the D, K and Ready LEDs are light up and you heard rising beep, the green car is ready to start. B) If you hear short multiple beeps, insert the just programmed key into the ignition coil, turn on the ignition/press START/STOP button and wait until programming is done (it can take from 10 to 60 seconds).
-
Page 8: Troubleshooting
• • • • • • • • • • • • • • • • • • Troubleshooting • • • • • • • • • • • • • • • • • • • • • • • • • •... - Page 9 Service Key This key allows you to unlock and lock a car central lock with the remote control but does not allow starting the engine! In case if all the data necessary for key programming was not read, the device can program the key only with the RF function.
- Page 10 HTPro / HTspy key The ADVANCED kit includes HTpro and HTspy keys for BMW and MINI. With these devices, you are able to ensure that all modules in the car are fully functional before programming a new key. This will allow you to avoid the situation...
- Page 11 HTpro / HTspy key To work with HTpro and HTspy Key devices you must use two programs: HTpro and HTag (for Windows computers). Here is the process of programming the HTspy key to check if all the necessary modules in the car are functional. 1.
Need help?
Do you have a question about the BMW OBDII and is the answer not in the manual?
Questions and answers