Table of Contents
Advertisement
Quick Links
User's Manual
For FD430
Digital 2-Phase Stepper Driver
All Rights Reserved, No reproduction
Changzhou Fulling Motor Co, Ltd
[Attention: Please read this manual carefully before using the drive!]
Add：No.69 KunLun Road, New District, Changzhou City, 213032, China
Tel：+86-519-85132957
Fax: +86-519-85132956
Web site：www.fullingmotor.com
Email:info@fullingmotor.com
Advertisement
Table of Contents
Related Manuals for Fulling Motor FD430
Summary of Contents for Fulling Motor FD430
- Page 1 User’s Manual For FD430 Digital 2-Phase Stepper Driver All Rights Reserved, No reproduction Changzhou Fulling Motor Co, Ltd [Attention: Please read this manual carefully before using the drive!] Add：No.69 KunLun Road, New District, Changzhou City, 213032, China Tel：+86-519-85132957 Fax: +86-519-85132956 Web site：www.fullingmotor.com...
-
Page 2: Table Of Contents
User’s Manual for FD430 Digital 2-Phase Stepper Driver User’s Manual for FD430 Digital 2-Phase Stepper Driver Contents Ⅰ.Product introduction ............. 错误!未定义书签。 1. Overview ......................... 3 2. Features ........................3 3. Applictaions ......................3 Ⅱ.Electrical, Meachanical, Environment Specifications ..错误!未定义书签。 1. Electrical Specifications ............错误!未定义书签。... -
Page 3: Overview
Ⅰ. Introduction, Features and Applications Ⅱ.Electrical, Mechanical, Environment Specifications 1. Introduction 1. Electrical Specifications The FD430 is the company’s new digital stepping driver based on the latest 32-bit FD430 Parameters ARM digital processing technology, Drive control algorithm uses advanced variable... -
Page 4: Mechanical Installation Dimensions Diagram
User’s Manual for FD430 Digital 2-Phase Stepper Driver User’s Manual for FD430 Digital 2-Phase Stepper Driver Ⅲ. Pin Assignment and Description Weight Approx. 0.090 Kg Mechanical Dimensions (unit: mm, 1 inch = 25.4 mm) 1. Interface description 1） Control Signal Connector... -
Page 5: Control Signal Interface Circuit
方向信号 Ω DIR- DIR+ 方向信号 Ω DIR- Notice: The FD430 RS232 cable must be a special cable, which is provided according to ENA+ 使能信号 Ω the user’s situation, Please confirm the cable before use to avoid damage. ENA+ ENA- 使能信号... -
Page 6: Control Signal Mode Setting
3200 number of resolution 3600 within the driver. Use PC 6400 This FD430 driver uses an 8-bit DIP switch to set microstep resolution, motor dynamic 12800 ProTuner software or current, standstill half-current, motor parameters and internal adjustment parameters 1000 STU debugger to set the... -
Page 7: Parameter Atuo-Tuning Function
For a given motor, higher driver current will make the motor to output more torque, but used to supply DC power to the FD430 driver. If regulated power supply is indeed used, at the same time causes more copper loss heating in the motor and driver. -
Page 8: 2）Set Value Of Output Curren
A+ and A-. FD430 driver can drive any 2-phase or 4-phase of 4, 6, 8- lead hybrid step motors. The following diagrams illustrate connection to various kinds of motor leads: 3. -
Page 9: Ⅷ.protection Functions
Figure8 Tandem and Parallel connection microstep resolution select the right microstep resolution 3） FD430 driver can only drive 2-phase hybrid step motors, which cannot drive 3-phase is too small setting Motor is not and 5-phase stepping motor. - Page 10 User’s Manual for FD430 Digital 2-Phase Stepper Driver User’s Manual for FD430 Digital 2-Phase Stepper Driver Choose another power supply with lager Current setting is too power or increase the output current of small, losing steps 3）What are the benefits of subdivision driver? drive.
-
Page 11: Product Warranty Terms
Changzhou Fulling Motor Co, Ltd. Warranty its products against defects in materials and workmanship for a period of 12 months from shipment out of factory. During the warranty period, Fulling Motor will either, at its option, repair or replace products which proved to be defective.
Need help?
Do you have a question about the FD430 and is the answer not in the manual?
Questions and answers