Summary of Contents for ABRATOOLS FTX-20-TS PRO
- Page 1 NS MANUAL DRILL PREs . s FTX-20-TS PRO * FTX-25-TC PRO , C i/Severo , O choa, 40�42 Po1.Jnd.Fo , nt del Radium 08403 Gr�nolleirs (B3i,eeloH) - Spain. Tel, +34 93 861 60 ?6 * Fax +l4 93 840 43 , Q , 8...
-
Page 3: Safety Rules
I. . SAFETY RULES General Safety Rules: 1. KEEP GUARDS IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS . A ND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 3. - Page 4 Special Safety Rules For Drill Pres.s: _ 1. Caution: Th is drill press is intended for use only with drill bits. The use of other accessories may be hazardous. 2. Correct drilling speeds: Factors which determine the best speed to use in any drill press operation are: ·...
- Page 5 III. PARTS Unpack carton, check your machine to see parts listed below: A. Main Parts: 1 pc. 1. Head assembly - - - - 1 1 pc. 2. Column with flarige 1 set. 3. Arm of table· and bracket 4. Table 1 pc.
- Page 7 4. Install table and clamp with bolt. Fig. 6. Fig. 6 5. Attach the Head Assembly • Carefully p ut the head assembly · o ver column and slide it onto colu mn into position. Align head frame with t able and base. Fix set screws in right side of head to lock head into position then tighten with alien wrench.
- Page 8 V •. ADJUSTMENT 1. Table Ad j ustment A. Height Ad j ust ment To adjust up or down , loosen the clamp bolt then adjust the table to your desired positioi:i b y t• ; rnin g the table bracket h andle. Fi g . 12. B.
- Page 9 3. Speed Adjustment 3-1 1. Open the pulley case and loosen the belt tension tock handle. 2. Choose speed for drilling ci p eration and move belt to correct position for desired speed. 3. Push motor backward until moderate belt tension is acquired.
-
Page 11: Troubleshooting Guide
4. Trouble Shooting Guide REMEDY PROBABLE CAUSE TROUBLE Incorrect belt tension Adjust tension Noisy operation B l Ory spindle Remove spindle/quill assembly- lubricate Loose pulley Tighten pulley Loose bel� Adjust belt tension Bad bearing Rep lace bearing Excess ive A) Loose chuck Tighten by pressing chuck down against table drill wobble... - Page 12 - 11 - • ..- • .. VtU...11.\. VV.l.'4.C ; -4.C,Vi... L VL".-:> 1. Connect to power according to Tocal regulations. 2. A separate electrical circuit should be used for your tools. This circuit should not be less than 1. 5m m wire and should be protected with a max. 10Amp time lag fu: If an extension cord is used, use 3-wire extension cords for 220v 1 ph, 4-wire extension cords for 380v Jph.
- Page 13 LS l Model ··· ·- • •· ·-·--------- ---------- ---------- ---------- 220 V l PHASE . , , , ·, � Power supply 220V 50llz 0.75mm D...rilling l!achine !"Phase Fuse Recom lfax. START m Motor Output Fuse Recom.Max. STOP o 0.-12 kW IO A Cll-6...
- Page 15 FTX-20-TS PRO * FTX-25-TC PRO...
- Page 16 FTX-20-TS PRO * FTX-25-TC PRO...